| Overview |
| -------- |
| - BSC9131 is integrated device that targets Femto base station market. |
| It combines Power Architecture e500v2 and DSP StarCore SC3850 core |
| technologies with MAPLE-B2F baseband acceleration processing elements. |
| - It's MAPLE disabled personality is called 9231. |
| |
| The BSC9131 SoC includes the following function and features: |
| . Power Architecture subsystem including a e500 processor with 256-Kbyte shared |
| L2 cache |
| . StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache |
| . The Multi Accelerator Platform Engine for Femto BaseStation Baseband |
| Processing (MAPLE-B2F) |
| . A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding, |
| Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing, |
| and CRC algorithms |
| . Consists of accelerators for Convolution, Filtering, Turbo Encoding, |
| Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion |
| operations |
| . DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with |
| ECC, up to 400-MHz clock/800 MHz data rate |
| . Dedicated security engine featuring trusted boot |
| . DMA controller |
| . OCNDMA with four bidirectional channels |
| . Interfaces |
| . Two triple-speed Gigabit Ethernet controllers featuring network acceleration |
| including IEEE 1588. v2 hardware support and virtualization (eTSEC) |
| . eTSEC 1 supports RGMII/RMII |
| . eTSEC 2 supports RGMII |
| . High-speed USB 2.0 host and device controller with ULPI interface |
| . Enhanced secure digital (SD/MMC) host controller (eSDHC) |
| . Antenna interface controller (AIC), supporting three industry standard |
| JESD207/three custom ADI RF interfaces (two dual port and one single port) |
| and three MAXIM's MaxPHY serial interfaces |
| . ADI lanes support both full duplex FDD support and half duplex TDD support |
| . Universal Subscriber Identity Module (USIM) interface that facilitates |
| communication to SIM cards or Eurochip pre-paid phone cards |
| . TDM with one TDM port |
| . Two DUART, four eSPI, and two I2C controllers |
| . Integrated Flash memory controller (IFC) |
| . TDM with 256 channels |
| . GPIO |
| . Sixteen 32-bit timers |
| |
| The e500 core subsystem within the Power Architecture consists of the following: |
| . 32-Kbyte L1 instruction cache |
| . 32-Kbyte L1 data cache |
| . 256-Kbyte L2 cache/L2 memory/L2 stash |
| . programmable interrupt controller (PIC) |
| . Debug support |
| . Timers |
| |
| The SC3850 core subsystem consists of the following: |
| . 32 Kbyte 8-way level 1 instruction cache (L1 ICache) |
| . 32 Kbyte 8-way level 1 data cache (L1 DCache) |
| . 512 Kbyte 8-way level 2 unified instruction/data cache (M2 memory) |
| . Memory management unit (MMU) |
| . Enhanced programmable interrupt controller (EPIC) |
| . Debug and profiling unit (DPU) |
| . Two 32-bit timers |
| |
| BSC9131RDB board Overview |
| ------------------------- |
| 1Gbyte DDR3 (on board DDR) |
| 128Mbyte 2K page size NAND Flash |
| 256 Kbit M24256 I2C EEPROM |
| 128 Mbit SPI Flash memory |
| USB-ULPI |
| eTSEC1: Connected to RGMII PHY |
| eTSEC2: Connected to RGMII PHY |
| DUART interface: supports one UARTs up to 115200 bps for console display |
| USIM connector |
| |
| Frequency Combinations Supported |
| -------------------------------- |
| Core MHz/CCB MHz/DDR(MT/s) |
| 1. 1000/500/800 |
| 2. 800/400/667 |
| |
| Boot Methods Supported |
| ----------------------- |
| 1. NAND Flash |
| 2. SPI Flash |
| |
| Default Boot Method |
| -------------------- |
| NAND boot |
| |
| Building U-boot |
| -------------- |
| To build the u-boot for BSC9131RDB: |
| 1. NAND Flash |
| make BSC9131RDB_NAND |
| 2. SPI Flash |
| make BSC9131RDB_SPIFLASH |
| |
| Memory map |
| ----------- |
| 0x0000_0000 0x7FFF_FFFF DDR 1G cacheable |
| 0xA0000000 0xBFFFFFFF Shared DSP core L2/M2 space 512M |
| 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M |
| 0xC1F0_0000 0xC1F3_FFFF PA SRAM Region 0 256K |
| 0xC1F8_0000 0xC1F9_FFFF PA SRAM Region 1 128K |
| 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K |
| 0xFEE0_0000 0xFEE0_0FFF DSP Boot ROM 4K |
| 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M |
| 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M |
| 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M |
| |
| Flashing Images |
| --------------- |
| To place a new u-boot image in the NAND flash and then boot |
| with that new image temporarily, use this: |
| tftp 1000000 u-boot-nand.bin |
| nand erase 0 100000 |
| nand write 1000000 0 100000 |
| reset |
| |
| Using the Device Tree Source File |
| --------------------------------- |
| To create the DTB (Device Tree Binary) image file, |
| use a command similar to this: |
| |
| dtc -b 0 -f -I dts -O dtb bsc9131rdb.dts > bsc9131rdb.dtb |
| |
| Likely, that .dts file will come from here; |
| |
| linux-2.6/arch/powerpc/boot/dts/bsc9131rdb.dts |
| |
| Booting Linux |
| ------------- |
| Place a linux uImage in the TFTP disk area. |
| |
| tftp 1000000 uImage |
| tftp 2000000 rootfs.ext2.gz.uboot |
| tftp c00000 bsc9131rdb.dtb |
| bootm 1000000 2000000 c00000 |
