blob: 566c42b6beccc5a620162f9d5c4a80fe96ff4f33 [file] [log] [blame]
/*
* (C) Copyright 2001-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC855 1 /* This is a MPC855 CPU */
#define CONFIG_C2MON 1 /* ...on a C2MON module */
#define CONFIG_SYS_TEXT_BASE 0x40000000
#define CONFIG_80MHz 1 /* Running at 5 * 16 = 80 MHz */
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
#if 0
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
#else
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
"bootp; " \
"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
"bootm"
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
#undef CONFIG_STATUS_LED /* Status LED disabled */
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_FEC_ENET 1 /* Use Fast Ethernet Controller */
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_IDE
#define CONFIG_CMD_NFS
#define CONFIG_CMD_SNTP
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CONFIG_SYS_IMMR 0xFFF00000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_FLASH_BASE 0x40000000
#if defined(DEBUG)
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#else
#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#endif
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
#ifndef CONFIG_CAN_DRIVER
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
#else /* we must activate GPL5 in the SIUMCR for CAN */
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
#endif /* CONFIG_CAN_DRIVER */
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* RTCSC - Real-Time Clock Status and Control Register 11-27
*-----------------------------------------------------------------------
*/
#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*-----------------------------------------------------------------------
* Reset PLL lock status sticky bit, timer expired status bit and timer
* interrupt status bit
*
* If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
*/
#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
#define CONFIG_SYS_PLPRCR \
( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
#else /* up to 50 MHz we use a 1:1 clock */
#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
#endif /* CONFIG_80MHz */
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ \
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
#else /* up to 50 MHz we use a 1:1 clock */
#define CONFIG_SYS_SCCR (SCCR_TBS | \
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
#endif /* CONFIG_80MHz */
/*-----------------------------------------------------------------------
* PCMCIA stuff
*-----------------------------------------------------------------------
*
*/
#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
/*-----------------------------------------------------------------------
* PCMCIA Power Switch
*
* The C2MON uses a TPS2211A PC-Card Power-Interface Switch to
* control the voltages on the PCMCIA slot which is connected
* to Port C (all outputs) and Port B (Over-Current Input)
*-----------------------------------------------------------------------
*/
/* Output pins */
#define TPS2211_VCCD0 0x0002 /* PC.14 */
#define TPS2211_VCCD1 0x0004 /* PC.13 */
#define TPS2211_VPPD0 0x0008 /* PC.12 */
#define TPS2211_VPPD1 0x0010 /* PC.11 */
#define TPS2211_OUTPUTS ( TPS2211_VCCD0 | TPS2211_VCCD1 | \
TPS2211_VPPD0 | TPS2211_VPPD1 )
/* Input pins */
#define TPS2211_OC 0x00000200 /* PB.22: Over-Current */
#define TPS2211_INPUTS ( TPS2211_OC )
/*-----------------------------------------------------------------------
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
*-----------------------------------------------------------------------
*/
#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
/* Offset for data I/O */
#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for normal register accesses */
#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for alternate registers */
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
#define CONFIG_SYS_DER 0
/*
* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
/* used to re-map FLASH both when starting from SRAM or FLASH:
* restrict access enough to keep SRAM working (if any)
* but not too much to meddle with FLASH accesses
*/
#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \
OR_SCY_5_CLK | OR_EHTR)
#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
/*
* BR2/3 and OR2/3 (SDRAM)
*
*/
#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
#ifndef CONFIG_CAN_DRIVER
#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
BR_PS_8 | BR_MS_UPMB | BR_V )
#endif /* CONFIG_CAN_DRIVER */
/*
* Memory Periodic Timer Prescaler
*/
/* periodic timer for refresh */
#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */
/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
/*
* MAMR settings for SDRAM
*/
/* 8 column SDRAM */
#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/* 9 column SDRAM */
#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
#endif /* __CONFIG_H */