| #!/usr/bin/perl | |
| # | |
| # Copyright 1998, 1999 Philip Edelbrock <phil@netroedge.com> | |
| # and Mark Studebaker <mdsxyz123@yahoo.com> | |
| # | |
| # Version 0.1 | |
| # | |
| # | |
| # ID ROM data decoding for Xeon processors. | |
| # Each Xeon processor contains two memories: | |
| # - A scratch EEPROM at an even location 0x50, 52, 54, or 56; | |
| # - An ID ROM at an odd location 0x51, 53, 55, or 57. | |
| # This program decodes the ID ROM's only. | |
| # The scratch EEPROMs have no prescribed format. | |
| # If the output of this program makes no sense for a particular device, | |
| # it is probably decoding a DIMM Serial Presence Detect (SPD) EEPROM. | |
| # See decode-dimms to decode those devices. | |
| # | |
| # | |
| # The eeprom driver must be loaded. For kernels older than 2.6.0, the | |
| # eeprom driver can be found in the lm-sensors package. | |
| # | |
| # To do: | |
| # Calculate and check checksums for each section | |
| # Decode flags in byte 0x7B (cartridge feature flags) | |
| # | |
| # References: | |
| # "Pentium II Xeon Processor at 400 and 450 MHz" Data Sheet | |
| # Intel | |
| # | |
| # | |
| # | |
| print "Xeon Processor Information ROM Decoder\n"; | |
| print "Written by Philip Edelbrock and Mark Studebaker. Copyright 1998, 1999.\n"; | |
| print "Version 2.6.3\n\n"; | |
| $dimm_count=0; | |
| $_=`ls /proc/sys/dev/sensors/`; | |
| @dimm_list=split(); | |
| for $i ( 0 .. $#dimm_list ) { | |
| $_=$dimm_list[$i]; | |
| if ((/^eeprom-/) && (/-51$/ || /-53$/ || /-55$/ || /-57$/)) { | |
| $dimm_count=$dimm_count + 1; | |
| print "\nDecoding Xeon ROM: /proc/sys/dev/sensors/$dimm_list[$i]\n"; | |
| if (/^[^-]+-[^-]+-[^-]+-([^-]+)$/) { | |
| $dimm_num=($1 - 49) / 2; | |
| print "Guessing Xeon is number $dimm_num\n"; | |
| } | |
| # Decode first 16 bytes | |
| print "\t\t----=== Xeon ROM Header Data ===----\n"; | |
| $_=`cat /proc/sys/dev/sensors/$dimm_list[$i]/00`; | |
| @bytes=split(" "); | |
| printf("\tData Format Revision: \t\t\t\t0x%.4X\n", $bytes[0]); | |
| print "\tTotal number of bytes in EEPROM:\t\t"; | |
| print ($bytes[1] << 4) + $bytes[2]; | |
| print "\n"; | |
| printf("\tProcessor Data Address:\t\t\t\t0x%.2X\n", $bytes[3]); | |
| printf("\tProcessor Core Data Address:\t\t\t0x%.2X\n", $bytes[4]); | |
| printf("\tL2 Cache Data Address:\t\t\t\t0x%.2X\n", $bytes[5]); | |
| printf("\tSEC Cartridge Data Address:\t\t\t0x%.2X\n", $bytes[6]); | |
| printf("\tPart Number Data Address:\t\t\t0x%.2X\n", $bytes[7]); | |
| printf("\tThermal Reference Data Address:\t\t\t0x%.2X\n", $bytes[8]); | |
| printf("\tFeature Data Address:\t\t\t\t0x%.2X\n", $bytes[9]); | |
| printf("\tOther Data Address:\t\t\t\t0x%.2X\n", $bytes[10]); | |
| print "\t\t----=== Xeon ROM Processor Data ===----\n"; | |
| # Decode next 16 bytes | |
| $_=`cat /proc/sys/dev/sensors/$dimm_list[$i]/10`; | |
| @bbytes=split(" "); | |
| print "\tS-spec/QDF Number:\t\t\t\t\""; | |
| print pack("cccccc",$bytes[14],$bytes[15],$bbytes[0], | |
| $bbytes[1],$bbytes[2],$bbytes[3]); | |
| print "\"\n"; | |
| $tmp = $bbytes[4] & 0xC0 >> 6; | |
| printf("\tSample / Production:\t\t\t\t0x%.2X", $tmp); | |
| if($tmp) { | |
| print " (Production)\n"; | |
| } else { | |
| print " (Sample)\n"; | |
| } | |
| print "\t\t----=== Xeon ROM Core Data ===----\n"; | |
| printf("\tProcessor Core Type:\t\t\t\t0x%.2X\n", | |
| ($bbytes[6] & 0xC0) >> 6); | |
| printf("\tProcessor Core Family:\t\t\t\t0x%.2X\n", | |
| ($bbytes[6] & 0x3C) >> 2); | |
| printf("\tProcessor Core Model:\t\t\t\t0x%.2X\n", | |
| (($bbytes[6] & 0x03) << 2) + (($bbytes[7] & 0xC0) >> 6)); | |
| printf("\tProcessor Core Stepping:\t\t\t0x%.2X\n", | |
| ($bbytes[7] & 0x30) >> 4); | |
| print "\tMaximum Core Frequency (Mhz):\t\t\t"; | |
| print ($bbytes[13] << 4) + $bbytes[14]; | |
| print "\n"; | |
| # Decode next 16 bytes (32-47) | |
| $_=`cat /proc/sys/dev/sensors/$dimm_list[$i]/20`; | |
| @bytes=split(" "); | |
| print "\tCore Voltage ID (mV):\t\t\t\t"; | |
| print ($bbytes[15] << 4) + $bytes[0]; | |
| print "\n"; | |
| print "\tCore Voltage Tolerance, High (mV):\t\t"; | |
| print $bytes[1]; | |
| print "\n"; | |
| print "\tCore Voltage Tolerance, Low (mV):\t\t"; | |
| print $bytes[2]; | |
| print "\n"; | |
| print "\t\t----=== Xeon ROM L2 Cache Data ===----\n"; | |
| print "\tL2 Cache Size (KB):\t\t\t\t"; | |
| print ($bytes[9] << 4) + $bytes[10]; | |
| print "\n"; | |
| printf("\tNumber of SRAM Components:\t\t\t%d\n", | |
| ($bytes[11] & 0xF0) >> 4); | |
| print "\tL2 Cache Voltage ID (mV):\t\t\t"; | |
| print ($bytes[12] << 4) + $bytes[13]; | |
| print "\n"; | |
| print "\tL2 Cache Voltage Tolerance, High (mV):\t\t"; | |
| print $bytes[14]; | |
| print "\n"; | |
| print "\tL2 Cache Voltage Tolerance, Low (mV):\t\t"; | |
| print $bytes[15]; | |
| print "\n"; | |
| # Decode next 16 bytes (48-63) | |
| $_=`cat /proc/sys/dev/sensors/$dimm_list[$i]/30`; | |
| @bytes=split(" "); | |
| printf("\tCache/Tag Stepping ID:\t\t\t\t0x%.2X\n", | |
| ($bytes[0] & 0xF0) >> 4); | |
| print "\t\t----=== Xeon ROM Cartridge Data ===----\n"; | |
| print "\tCartridge Revision:\t\t\t\t\""; | |
| print pack("cccc",$bytes[2],$bytes[3],$bytes[4],$bytes[5]); | |
| print "\"\n"; | |
| printf("\tSubstrate Rev. Software ID:\t\t\t0x%.2X\n", | |
| ($bbytes[6] & 0xC0) >> 6); | |
| print "\t\t----=== Xeon ROM Part Number Data ===----\n"; | |
| print "\tProcessor Part Number:\t\t\t\t\""; | |
| print pack("ccccccc",$bytes[8],$bytes[9],$bytes[10], | |
| $bytes[11],$bytes[12],$bytes[13],$bytes[14]); | |
| print "\"\n"; | |
| $byte15=$byte[15]; | |
| # Decode next 16 bytes (64-79) | |
| $_=`cat /proc/sys/dev/sensors/$dimm_list[$i]/40`; | |
| @bytes=split(" "); | |
| print "\tProcessor BOM ID:\t\t\t\t\""; | |
| print pack("cccccccccccccc",$byte15,$bytes[0],$bytes[1], | |
| $bytes[2],$bytes[3],$bytes[4],$bytes[5],$bytes[6], | |
| $bytes[7],$bytes[8],$bytes[9],$bytes[10],$bytes[11], | |
| $bytes[12]); | |
| print "\"\n"; | |
| # Decode next 16 bytes (80-95) | |
| $_=`cat /proc/sys/dev/sensors/$dimm_list[$i]/50`; | |
| @bbytes=split(" "); | |
| printf("\tProcessor Electronic Signature: \t\t0x%.2X%.2X%.2X%.2X%.2X%.2X%.2X%.2X\n", | |
| $bytes[13],$bytes[14],$bytes[15],$bbytes[0], | |
| $bbytes[1],$bbytes[2],$bbytes[3],$bbytes[4]); | |
| # Decode next 16 bytes (96-111) | |
| # Not used... | |
| # Decode next 16 bytes (112-127) | |
| $_=`cat /proc/sys/dev/sensors/$dimm_list[$i]/70`; | |
| @bytes=split(" "); | |
| print "\t\t----=== Xeon Thermal Reference Data ===----\n"; | |
| printf("\tThermal Reference Byte: \t\t\t0x%.2X\n", $bytes[0]); | |
| print "\t\t----=== Xeon ROM Feature Data ===----\n"; | |
| printf("\tProcessor Core Feature Flags: \t\t\t0x%.2X%.2X%.2X%.2X\n", | |
| $bytes[4],$bytes[5],$bytes[6],$bytes[7]); | |
| printf("\tCartridge Feature Flags: \t\t\t0x%.2X%.2X%.2X%.2X\n", | |
| $bytes[8],$bytes[9],$bytes[10],$bytes[11]); | |
| printf("\tNumber of Devices in TAP Chain:\t\t\t%d\n", | |
| ($bytes[12] & 0xF0) >> 4); | |
| } | |
| } | |
| print "\n\nNumber of Xeon ROMs detected and decoded: $dimm_count\n"; |