blob: f77e3d0ab5c4dfd43ab73034c2878af9fd95ffd9 [file] [log] [blame] [edit]
/*
* (C) Copyright 2011
* Marvell Semiconductor <www.marvell.com>
* Written-by: Lei Wen <leiwen@marvell.com>,
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/pantheon.h>
DECLARE_GLOBAL_DATA_PTR;
/*
* Pantheon DRAM controller supports upto 8 banks
* for chip select 0 and 1
*/
/*
* DDR Memory Control Registers
* Refer Datasheet 4.4
*/
struct panthddr_map_registers {
u32 cs; /* Memory Address Map Register -CS */
u32 pad[3];
};
struct panthddr_registers {
u8 pad[0x100 - 0x000];
struct panthddr_map_registers mmap[2];
};
/*
* panth_sdram_base - reads SDRAM Base Address Register
*/
u32 panth_sdram_base(int chip_sel)
{
struct panthddr_registers *ddr_regs =
(struct panthddr_registers *)PANTHEON_DRAM_BASE;
u32 result = 0;
u32 CS_valid = 0x01 & readl(&ddr_regs->mmap[chip_sel].cs);
if (!CS_valid)
return 0;
result = readl(&ddr_regs->mmap[chip_sel].cs) & 0xFF800000;
return result;
}
/*
* panth_sdram_size - reads SDRAM size
*/
u32 panth_sdram_size(int chip_sel)
{
struct panthddr_registers *ddr_regs =
(struct panthddr_registers *)PANTHEON_DRAM_BASE;
u32 result = 0;
u32 CS_valid = 0x01 & readl(&ddr_regs->mmap[chip_sel].cs);
if (!CS_valid)
return 0;
result = readl(&ddr_regs->mmap[chip_sel].cs);
result = (result >> 16) & 0xF;
if (result < 0x7) {
printf("Unknown DRAM Size\n");
return -1;
} else {
return ((0x8 << (result - 0x7)) * 1024 * 1024);
}
}
#ifndef CONFIG_SYS_BOARD_DRAM_INIT
int dram_init(void)
{
int i;
gd->ram_size = 0;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
gd->bd->bi_dram[i].start = panth_sdram_base(i);
gd->bd->bi_dram[i].size = panth_sdram_size(i);
/*
* It is assumed that all memory banks are consecutive
* and without gaps.
* If the gap is found, ram_size will be reported for
* consecutive memory only
*/
if (gd->bd->bi_dram[i].start != gd->ram_size)
break;
gd->ram_size += gd->bd->bi_dram[i].size;
}
for (; i < CONFIG_NR_DRAM_BANKS; i++) {
/*
* If above loop terminated prematurely, we need to set
* remaining banks' start address & size as 0. Otherwise other
* u-boot functions and Linux kernel gets wrong values which
* could result in crash
*/
gd->bd->bi_dram[i].start = 0;
gd->bd->bi_dram[i].size = 0;
}
return 0;
}
/*
* If this function is not defined here,
* board.c alters dram bank zero configuration defined above.
*/
void dram_init_banksize(void)
{
dram_init();
}
#endif /* CONFIG_SYS_BOARD_DRAM_INIT */