| /* Copyright (c) 2007 Intel Corporation */ |
| #include <stdio.h> |
| #include "ethtool-util.h" |
| |
| /* Register Bit Masks */ |
| /* Device Control */ |
| #define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */ |
| #define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */ |
| #define E1000_CTRL_GIOMASTERD 0x00000008 /* GIO Master Disable*/ |
| #define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */ |
| #define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */ |
| #define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */ |
| #define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */ |
| #define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */ |
| #define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */ |
| #define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */ |
| #define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */ |
| #define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */ |
| #define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */ |
| #define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */ |
| #define E1000_CTRL_SDP0_GPIEN 0x00010000 /* General Purpose Interrupt Detection Enable for SDP0 */ |
| #define E1000_CTRL_SDP1_GPIEN 0x00020000 /* General Purpose Interrupt Detection Enable for SDP1 */ |
| #define E1000_CTRL_SDP0_DATA 0x00040000 /* SDP0 Data */ |
| #define E1000_CTRL_SDP1_DATA 0x00080000 /* SDP1 Data */ |
| #define E1000_CTRL_ADVD3WUC 0x00100000 /* D3Cold WakeUp Capability Advertisement Enable */ |
| #define E1000_CTRL_SDP0_WDE 0x00200000 /* Watchdog Indication for SDP0 */ |
| #define E1000_CTRL_SDP1_IODIR 0x00400000 /* SDP1 Directionality */ |
| #define E1000_CTRL_RST 0x04000000 /* Global reset */ |
| #define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */ |
| #define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */ |
| #define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */ |
| #define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */ |
| |
| /* Device Status */ |
| #define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */ |
| #define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */ |
| #define E1000_STATUS_LANID 0x00000008 /* LAN ID */ |
| #define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */ |
| #define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */ |
| #define E1000_STATUS_SPEED_MASK 0x000000C0 /* Speed Mask */ |
| #define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */ |
| #define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */ |
| #define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */ |
| #define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */ |
| #define E1000_STATUS_PHYRA 0x00000400 /* PHY Reset Asserted */ |
| #define E1000_STATUS_GIOMASTEREN 0x00080000 /* GIO Master Enable Status */ |
| #define E1000_STATUS_DMA_CGEN 0x80000000 /* DMA clock gating Enable */ |
| |
| /* Receive Control */ |
| #define E1000_RCTL_EN 0x00000002 /* enable */ |
| #define E1000_RCTL_SBP 0x00000004 /* store bad packet */ |
| #define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */ |
| #define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */ |
| #define E1000_RCTL_LPE 0x00000020 /* long packet enable */ |
| #define E1000_RCTL_LBM_MASK 0x000000C0 /* Loopback mode mask */ |
| #define E1000_RCTL_LBM_NORM 0x00000000 /* normal loopback mode */ |
| #define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */ |
| #define E1000_RCTL_LBM_SERDES 0x000000C0 /* SERDES loopback mode */ |
| #define E1000_RCTL_RDMTS 0x00000300 /* rx desc min threshold size */ |
| #define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */ |
| #define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */ |
| #define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */ |
| #define E1000_RCTL_MO 0x00003000 /* multicast offset shift */ |
| #define E1000_RCTL_MO_0 0x00000000 /* multicast offset 47:36 */ |
| #define E1000_RCTL_MO_1 0x00001000 /* multicast offset 46:35 */ |
| #define E1000_RCTL_MO_2 0x00002000 /* multicast offset 45:34 */ |
| #define E1000_RCTL_MO_3 0x00003000 /* multicast offset 43:32 */ |
| #define E1000_RCTL_BAM 0x00008000 /* broadcast enable */ |
| #define E1000_RCTL_BSIZE 0x00030000 /* rx buffer size */ |
| #define E1000_RCTL_BSIZE_2048 0x00000000 /* rx buffer size 2048 */ |
| #define E1000_RCTL_BSIZE_1024 0x00010000 /* rx buffer size 1024 */ |
| #define E1000_RCTL_BSIZE_512 0x00020000 /* rx buffer size 512 */ |
| #define E1000_RCTL_BSIZE_256 0x00030000 /* rx buffer size 256 */ |
| #define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */ |
| #define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */ |
| #define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */ |
| #define E1000_RCTL_DPF 0x00400000 /* discard pause frames */ |
| #define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */ |
| #define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC from packet.0=No strip;1=strip */ |
| |
| /* Transmit Control */ |
| #define E1000_TCTL_EN 0x00000002 /* enable tx */ |
| #define E1000_TCTL_PSP 0x00000008 /* pad short packets */ |
| #define E1000_TCTL_CT 0x00000ff0 /* collision threshold */ |
| #define E1000_TCTL_BST 0x003ff000 /* Backoff Slot time */ |
| #define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */ |
| #define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */ |
| #define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */ |
| #define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */ |
| |
| int |
| igb_dump_regs(struct ethtool_drvinfo *info, struct ethtool_regs *regs) |
| { |
| u32 *regs_buff = (u32 *)regs->data; |
| u32 reg; |
| u8 i; |
| u8 version = (u8)(regs->version >> 24); |
| |
| if (version != 1) |
| return -1; |
| |
| /* Device control register */ |
| reg = regs_buff[0]; |
| fprintf(stdout, |
| "0x00000: CTRL (Device control register) 0x%08X\n" |
| " Invert Loss-Of-Signal: %s\n" |
| " Receive flow control: %s\n" |
| " Transmit flow control: %s\n" |
| " VLAN mode: %s\n" |
| " Set link up: %s\n" |
| " D3COLD WakeUp capability advertisement: %s\n", |
| reg, |
| reg & E1000_CTRL_ILOS ? "yes" : "no", |
| reg & E1000_CTRL_RFCE ? "enabled" : "disabled", |
| reg & E1000_CTRL_TFCE ? "enabled" : "disabled", |
| reg & E1000_CTRL_VME ? "enabled" : "disabled", |
| reg & E1000_CTRL_SLU ? "1" : "0", |
| reg & E1000_CTRL_ADVD3WUC ? "enabled" : "disabled"); |
| fprintf(stdout, |
| " Auto speed detect: %s\n" |
| " Speed select: %s\n" |
| " Force speed: %s\n" |
| " Force duplex: %s\n", |
| reg & E1000_CTRL_ASDE ? "enabled" : "disabled", |
| (reg & E1000_CTRL_SPD_SEL) == E1000_CTRL_SPD_10 ? "10Mb/s" : |
| (reg & E1000_CTRL_SPD_SEL) == E1000_CTRL_SPD_100 ? "100Mb/s" : |
| (reg & E1000_CTRL_SPD_SEL) == E1000_CTRL_SPD_1000 ? "1000Mb/s" : |
| "not used", |
| reg & E1000_CTRL_FRCSPD ? "yes" : "no", |
| reg & E1000_CTRL_FRCDPX ? "yes" : "no"); |
| |
| /* Device status register */ |
| reg = regs_buff[1]; |
| fprintf(stdout, |
| "0x00008: STATUS (Device status register) 0x%08X\n" |
| " Duplex: %s\n" |
| " Link up: %s\n" |
| " Transmission: %s\n" |
| " DMA clock gating: %s\n", |
| reg, |
| reg & E1000_STATUS_FD ? "full" : "half", |
| reg & E1000_STATUS_LU ? "link config" : "no link config", |
| reg & E1000_STATUS_TXOFF ? "paused" : "on", |
| reg & E1000_STATUS_DMA_CGEN ? "enabled" : "disabled"); |
| fprintf(stdout, |
| " TBI mode: %s\n" |
| " Link speed: %s\n" |
| " Bus type: %s\n", |
| reg & E1000_STATUS_TBIMODE ? "enabled" : "disabled", |
| (reg & E1000_STATUS_SPEED_MASK) == E1000_STATUS_SPEED_10 ? |
| "10Mb/s" : |
| (reg & E1000_STATUS_SPEED_MASK) == E1000_STATUS_SPEED_100 ? |
| "100Mb/s" : |
| (reg & E1000_STATUS_SPEED_MASK) == E1000_STATUS_SPEED_1000 ? |
| "1000Mb/s" : "not used", |
| "PCI Express"); |
| |
| /* Receive control register */ |
| reg = regs_buff[32]; |
| fprintf(stdout, |
| "0x00100: RCTL (Receive control register) 0x%08X\n" |
| " Receiver: %s\n" |
| " Store bad packets: %s\n" |
| " Unicast promiscuous: %s\n" |
| " Multicast promiscuous: %s\n" |
| " Long packet: %s\n" |
| " Descriptor minimum threshold size: %s\n" |
| " Broadcast accept mode: %s\n" |
| " VLAN filter: %s\n" |
| " Cononical form indicator: %s\n" |
| " Discard pause frames: %s\n" |
| " Pass MAC control frames: %s\n" |
| " Loopback mode: %s\n", |
| reg, |
| reg & E1000_RCTL_EN ? "enabled" : "disabled", |
| reg & E1000_RCTL_SBP ? "enabled" : "disabled", |
| reg & E1000_RCTL_UPE ? "enabled" : "disabled", |
| reg & E1000_RCTL_MPE ? "enabled" : "disabled", |
| reg & E1000_RCTL_LPE ? "enabled" : "disabled", |
| (reg & E1000_RCTL_RDMTS) == E1000_RCTL_RDMTS_HALF ? "1/2" : |
| (reg & E1000_RCTL_RDMTS) == E1000_RCTL_RDMTS_QUAT ? "1/4" : |
| (reg & E1000_RCTL_RDMTS) == E1000_RCTL_RDMTS_EIGTH ? "1/8" : |
| "reserved", |
| reg & E1000_RCTL_BAM ? "accept" : "ignore", |
| reg & E1000_RCTL_VFE ? "enabled" : "disabled", |
| reg & E1000_RCTL_CFIEN ? "enabled" : "disabled", |
| reg & E1000_RCTL_DPF ? "ignored" : "filtered", |
| reg & E1000_RCTL_PMCF ? "pass" : "don't pass", |
| (reg & E1000_RCTL_LBM_MASK) == E1000_RCTL_LBM_NORM ? "normal" : |
| (reg & E1000_RCTL_LBM_MASK) == E1000_RCTL_LBM_MAC ? "MAC": |
| (reg & E1000_RCTL_LBM_MASK) == E1000_RCTL_LBM_SERDES ? "SERDES": |
| "undefined"); |
| fprintf(stdout, |
| " Receive buffer size: %s\n", |
| (reg & E1000_RCTL_BSIZE)==E1000_RCTL_BSIZE_2048 ? "2048" : |
| (reg & E1000_RCTL_BSIZE)==E1000_RCTL_BSIZE_1024 ? "1024" : |
| (reg & E1000_RCTL_BSIZE)==E1000_RCTL_BSIZE_512 ? "512" : |
| "256"); |
| |
| /* Receive descriptor registers */ |
| fprintf(stdout, |
| "0x02808: RDLEN (Receive desc length) 0x%08X\n", |
| regs_buff[142]); |
| fprintf(stdout, |
| "0x02810: RDH (Receive desc head) 0x%08X\n", |
| regs_buff[146]); |
| fprintf(stdout, |
| "0x02818: RDT (Receive desc tail) 0x%08X\n", |
| regs_buff[150]); |
| |
| /* Transmit control register */ |
| reg = regs_buff[38]; |
| fprintf(stdout, |
| "0x00400: TCTL (Transmit ctrl register) 0x%08X\n" |
| " Transmitter: %s\n" |
| " Pad short packets: %s\n" |
| " Software XOFF Transmission: %s\n", |
| reg, |
| reg & E1000_TCTL_EN ? "enabled" : "disabled", |
| reg & E1000_TCTL_PSP ? "enabled" : "disabled", |
| reg & E1000_TCTL_SWXOFF ? "enabled" : "disabled"); |
| fprintf(stdout, |
| " Re-transmit on late collision: %s\n", |
| reg & E1000_TCTL_RTLC ? "enabled" : "disabled"); |
| |
| /* Transmit descriptor registers */ |
| fprintf(stdout, |
| "0x03808: TDLEN (Transmit desc length) 0x%08X\n", |
| regs_buff[214]); |
| fprintf(stdout, |
| "0x03810: TDH (Transmit desc head) 0x%08X\n", |
| regs_buff[218]); |
| fprintf(stdout, |
| "0x03818: TDT (Transmit desc tail) 0x%08X\n", |
| regs_buff[222]); |
| |
| |
| fprintf(stdout, |
| "0x00018: CTRL_EXT (Extended device control) 0x%08X\n", |
| regs_buff[2]); |
| |
| fprintf(stdout, |
| "0x00018: MDIC (MDI control) 0x%08X\n", |
| regs_buff[3]); |
| |
| fprintf(stdout, |
| "0x00024: SCTL (SERDES ANA) 0x%08X\n", |
| regs_buff[4]); |
| |
| fprintf(stdout, |
| "0x00034: CONNSW (Copper/Fiber switch control) 0x%08X\n", |
| regs_buff[5]); |
| |
| fprintf(stdout, |
| "0x00038: VET (VLAN Ether type) 0x%08X\n", |
| regs_buff[6]); |
| |
| fprintf(stdout, |
| "0x00E00: LEDCTL (LED control) 0x%08X\n", |
| regs_buff[7]); |
| |
| fprintf(stdout, |
| "0x01000: PBA (Packet buffer allocation) 0x%08X\n", |
| regs_buff[8]); |
| |
| fprintf(stdout, |
| "0x01008: PBS (Packet buffer size) 0x%08X\n", |
| regs_buff[9]); |
| |
| fprintf(stdout, |
| "0x01048: FRTIMER (Free running timer) 0x%08X\n", |
| regs_buff[10]); |
| |
| fprintf(stdout, |
| "0x0104C: TCPTIMER (TCP timer) 0x%08X\n", |
| regs_buff[11]); |
| |
| fprintf(stdout, |
| "0x00010: EEC (EEPROM/FLASH control) 0x%08X\n", |
| regs_buff[12]); |
| |
| fprintf(stdout, |
| "0x01580: EICR (Extended interrupt cause) 0x%08X\n", |
| regs_buff[13]); |
| |
| fprintf(stdout, |
| "0x01520: EICS (Extended interrupt cause set) 0x%08X\n", |
| regs_buff[14]); |
| |
| fprintf(stdout, |
| "0x01524: EIMS (Extended interrup set/read) 0x%08X\n", |
| regs_buff[15]); |
| |
| fprintf(stdout, |
| "0x01528: EIMC (Extended interrupt mask clear) 0x%08X\n", |
| regs_buff[16]); |
| |
| fprintf(stdout, |
| "0x0152C: EIAC (Extended interrupt auto clear) 0x%08X\n", |
| regs_buff[17]); |
| |
| fprintf(stdout, |
| "0x01530: EIAM (Extended interrupt auto mask) 0x%08X\n", |
| regs_buff[18]); |
| |
| fprintf(stdout, |
| "0x01500: ICR (Interrupt cause read) 0x%08X\n", |
| regs_buff[19]); |
| |
| fprintf(stdout, |
| "0x01504: ICS (Interrupt cause set) 0x%08X\n", |
| regs_buff[20]); |
| |
| fprintf(stdout, |
| "0x01508: IMS (Interrupt mask set/read) 0x%08X\n", |
| regs_buff[21]); |
| |
| fprintf(stdout, |
| "0x0150C: IMC (Interrupt mask clear) 0x%08X\n", |
| regs_buff[22]); |
| |
| fprintf(stdout, |
| "0x04100: IAC (Interrupt assertion count) 0x%08X\n", |
| regs_buff[23]); |
| |
| fprintf(stdout, |
| "0x01510: IAM (Interr acknowledge auto-mask) 0x%08X\n", |
| regs_buff[24]); |
| |
| fprintf(stdout, |
| "0x05AC0: IMIRVP (Immed interr rx VLAN priority) 0x%08X\n", |
| regs_buff[25]); |
| |
| fprintf(stdout, |
| "0x00028: FCAL (Flow control address low) 0x%08X\n", |
| regs_buff[26]); |
| |
| fprintf(stdout, |
| "0x0002C: FCAH (Flow control address high) 0x%08X\n", |
| regs_buff[27]); |
| |
| fprintf(stdout, |
| "0x00170: FCTTV (Flow control tx timer value) 0x%08X\n", |
| regs_buff[28]); |
| |
| fprintf(stdout, |
| "0x02160: FCRTL (Flow control rx threshold low) 0x%08X\n", |
| regs_buff[29]); |
| |
| fprintf(stdout, |
| "0x02168: FCRTH (Flow control rx threshold high) 0x%08X\n", |
| regs_buff[30]); |
| |
| fprintf(stdout, |
| "0x02460: FCRTV (Flow control refresh threshold) 0x%08X\n", |
| regs_buff[31]); |
| |
| fprintf(stdout, |
| "0x05000: RXCSUM (Receive checksum control) 0x%08X\n", |
| regs_buff[33]); |
| |
| fprintf(stdout, |
| "0x05004: RLPML (Receive long packet max length) 0x%08X\n", |
| regs_buff[34]); |
| |
| fprintf(stdout, |
| "0x05008: RFCTL (Receive filter control) 0x%08X\n", |
| regs_buff[35]); |
| |
| fprintf(stdout, |
| "0x05818: MRQC (Multiple rx queues command) 0x%08X\n", |
| regs_buff[36]); |
| |
| fprintf(stdout, |
| "0x0581C: VMD_CTL (VMDq control) 0x%08X\n", |
| regs_buff[37]); |
| |
| fprintf(stdout, |
| "0x00404: TCTL_EXT (Transmit control extended) 0x%08X\n", |
| regs_buff[39]); |
| |
| fprintf(stdout, |
| "0x00410: TIPG (Transmit IPG) 0x%08X\n", |
| regs_buff[40]); |
| |
| fprintf(stdout, |
| "0x03590: DTXCTL (DMA tx control) 0x%08X\n", |
| regs_buff[41]); |
| |
| fprintf(stdout, |
| "0x05800: WUC (Wake up control) 0x%08X\n", |
| regs_buff[42]); |
| |
| fprintf(stdout, |
| "0x05808: WUFC (Wake up filter control) 0x%08X\n", |
| regs_buff[43]); |
| |
| fprintf(stdout, |
| "0x05810: WUS (Wake up status) 0x%08X\n", |
| regs_buff[44]); |
| |
| fprintf(stdout, |
| "0x05838: IPAV (IP address valid) 0x%08X\n", |
| regs_buff[45]); |
| |
| fprintf(stdout, |
| "0x05900: WUPL (Wake up packet length) 0x%08X\n", |
| regs_buff[46]); |
| |
| fprintf(stdout, |
| "0x04200: PCS_CFG (PCS configuration 0) 0x%08X\n", |
| regs_buff[47]); |
| |
| fprintf(stdout, |
| "0x04208: PCS_LCTL (PCS link control) 0x%08X\n", |
| regs_buff[48]); |
| |
| fprintf(stdout, |
| "0x0420C: PCS_LSTS (PCS link status) 0x%08X\n", |
| regs_buff[49]); |
| |
| fprintf(stdout, |
| "0x04218: PCS_ANADV (AN advertisement) 0x%08X\n", |
| regs_buff[50]); |
| |
| fprintf(stdout, |
| "0x0421C: PCS_LPAB (Link partner ability) 0x%08X\n", |
| regs_buff[51]); |
| |
| fprintf(stdout, |
| "0x04220: PCS_NPTX (Next Page transmit) 0x%08X\n", |
| regs_buff[52]); |
| |
| fprintf(stdout, |
| "0x04224: PCS_LPABNP (Link partner ability Next Page) 0x%08X\n", |
| regs_buff[53]); |
| |
| fprintf(stdout, |
| "0x04000: CRCERRS (CRC error count) 0x%08X\n", |
| regs_buff[54]); |
| |
| fprintf(stdout, |
| "0x04004: ALGNERRC (Alignment error count) 0x%08X\n", |
| regs_buff[55]); |
| |
| fprintf(stdout, |
| "0x04008: SYMERRS (Symbol error count) 0x%08X\n", |
| regs_buff[56]); |
| |
| fprintf(stdout, |
| "0x0400C: RXERRC (RX error count) 0x%08X\n", |
| regs_buff[57]); |
| |
| fprintf(stdout, |
| "0x04010: MPC (Missed packets count) 0x%08X\n", |
| regs_buff[58]); |
| |
| fprintf(stdout, |
| "0x04014: SCC (Single collision count) 0x%08X\n", |
| regs_buff[59]); |
| |
| fprintf(stdout, |
| "0x04018: ECOL (Excessive collisions count) 0x%08X\n", |
| regs_buff[60]); |
| |
| fprintf(stdout, |
| "0x0401C: MCC (Multiple collision count) 0x%08X\n", |
| regs_buff[61]); |
| |
| fprintf(stdout, |
| "0x04020: LATECOL (Late collisions count) 0x%08X\n", |
| regs_buff[62]); |
| |
| fprintf(stdout, |
| "0x04028: COLC (Collision count) 0x%08X\n", |
| regs_buff[63]); |
| |
| fprintf(stdout, |
| "0x04030: DC (Defer count) 0x%08X\n", |
| regs_buff[64]); |
| |
| fprintf(stdout, |
| "0x04034: TNCRS (Transmit with no CRS) 0x%08X\n", |
| regs_buff[65]); |
| |
| fprintf(stdout, |
| "0x04038: SEC (Sequence error count) 0x%08X\n", |
| regs_buff[66]); |
| |
| fprintf(stdout, |
| "0x0403C: HTDPMC (Host tx discrd pkts MAC count) 0x%08X\n", |
| regs_buff[67]); |
| |
| fprintf(stdout, |
| "0x04040: RLEC (Receive length error count) 0x%08X\n", |
| regs_buff[68]); |
| |
| fprintf(stdout, |
| "0x04048: XONRXC (XON received count) 0x%08X\n", |
| regs_buff[69]); |
| |
| fprintf(stdout, |
| "0x0404C: XONTXC (XON transmitted count) 0x%08X\n", |
| regs_buff[70]); |
| |
| fprintf(stdout, |
| "0x04050: XOFFRXC (XOFF received count) 0x%08X\n", |
| regs_buff[71]); |
| |
| fprintf(stdout, |
| "0x04054: XOFFTXC (XOFF transmitted count) 0x%08X\n", |
| regs_buff[72]); |
| |
| fprintf(stdout, |
| "0x04058: FCRUC (FC received unsupported count) 0x%08X\n", |
| regs_buff[73]); |
| |
| fprintf(stdout, |
| "0x0405C: PRC64 (Packets rx (64 B) count) 0x%08X\n", |
| regs_buff[74]); |
| |
| fprintf(stdout, |
| "0x04060: PRC127 (Packets rx (65-127 B) count) 0x%08X\n", |
| regs_buff[75]); |
| |
| fprintf(stdout, |
| "0x04064: PRC255 (Packets rx (128-255 B) count) 0x%08X\n", |
| regs_buff[76]); |
| |
| fprintf(stdout, |
| "0x04068: PRC511 (Packets rx (256-511 B) count) 0x%08X\n", |
| regs_buff[77]); |
| |
| fprintf(stdout, |
| "0x0406C: PRC1023 (Packets rx (512-1023 B) count) 0x%08X\n", |
| regs_buff[78]); |
| |
| fprintf(stdout, |
| "0x04070: PRC1522 (Packets rx (1024-max B) count) 0x%08X\n", |
| regs_buff[79]); |
| |
| fprintf(stdout, |
| "0x04074: GPRC (Good packets received count) 0x%08X\n", |
| regs_buff[80]); |
| |
| fprintf(stdout, |
| "0x04078: BPRC (Broadcast packets rx count) 0x%08X\n", |
| regs_buff[81]); |
| |
| fprintf(stdout, |
| "0x0407C: MPRC (Multicast packets rx count) 0x%08X\n", |
| regs_buff[82]); |
| |
| fprintf(stdout, |
| "0x04080: GPTC (Good packets tx count) 0x%08X\n", |
| regs_buff[83]); |
| |
| fprintf(stdout, |
| "0x04088: GORCL (Good octets rx count lower) 0x%08X\n", |
| regs_buff[84]); |
| |
| fprintf(stdout, |
| "0x0408C: GORCH (Good octets rx count upper) 0x%08X\n", |
| regs_buff[85]); |
| |
| fprintf(stdout, |
| "0x04090: GOTCL (Good octets tx count lower) 0x%08X\n", |
| regs_buff[86]); |
| |
| fprintf(stdout, |
| "0x04094: GOTCH (Good octets tx count upper) 0x%08X\n", |
| regs_buff[87]); |
| |
| fprintf(stdout, |
| "0x040A0: RNBC (Receive no buffers count) 0x%08X\n", |
| regs_buff[88]); |
| |
| fprintf(stdout, |
| "0x040A4: RUC (Receive undersize count) 0x%08X\n", |
| regs_buff[89]); |
| |
| fprintf(stdout, |
| "0x040A8: RFC (Receive fragment count) 0x%08X\n", |
| regs_buff[90]); |
| |
| fprintf(stdout, |
| "0x040AC: ROC (Receive oversize count) 0x%08X\n", |
| regs_buff[91]); |
| |
| fprintf(stdout, |
| "0x040B0: RJC (Receive jabber count) 0x%08X\n", |
| regs_buff[92]); |
| |
| fprintf(stdout, |
| "0x040B4: MGPRC (Management packets rx count) 0x%08X\n", |
| regs_buff[93]); |
| |
| fprintf(stdout, |
| "0x040B8: MGPDC (Management pkts dropped count) 0x%08X\n", |
| regs_buff[94]); |
| |
| fprintf(stdout, |
| "0x040BC: MGPTC (Management packets tx count) 0x%08X\n", |
| regs_buff[95]); |
| |
| fprintf(stdout, |
| "0x040C0: TORL (Total octets received lower) 0x%08X\n", |
| regs_buff[96]); |
| |
| fprintf(stdout, |
| "0x040C4: TORH (Total octets received upper) 0x%08X\n", |
| regs_buff[97]); |
| |
| fprintf(stdout, |
| "0x040C8: TOTL (Total octets transmitted lower) 0x%08X\n", |
| regs_buff[98]); |
| |
| fprintf(stdout, |
| "0x040CC: TOTH (Total octets transmitted upper) 0x%08X\n", |
| regs_buff[99]); |
| |
| fprintf(stdout, |
| "0x040D0: TPR (Total packets received) 0x%08X\n", |
| regs_buff[100]); |
| |
| fprintf(stdout, |
| "0x040D4: TPT (Total packets transmitted) 0x%08X\n", |
| regs_buff[101]); |
| |
| fprintf(stdout, |
| "0x040D8: PTC64 (Packets tx (64 B) count) 0x%08X\n", |
| regs_buff[102]); |
| |
| fprintf(stdout, |
| "0x040DC: PTC127 (Packets tx (65-127 B) count) 0x%08X\n", |
| regs_buff[103]); |
| |
| fprintf(stdout, |
| "0x040E0: PTC255 (Packets tx (128-255 B) count) 0x%08X\n", |
| regs_buff[104]); |
| |
| fprintf(stdout, |
| "0x040E4: PTC511 (Packets tx (256-511 B) count) 0x%08X\n", |
| regs_buff[105]); |
| |
| fprintf(stdout, |
| "0x040E8: PTC1023 (Packets tx (512-1023 B) count) 0x%08X\n", |
| regs_buff[106]); |
| |
| fprintf(stdout, |
| "0x040EC: PTC1522 (Packets tx (> 1024 B) count) 0x%08X\n", |
| regs_buff[107]); |
| |
| fprintf(stdout, |
| "0x040F0: MPTC (Multicast packets tx count) 0x%08X\n", |
| regs_buff[108]); |
| |
| fprintf(stdout, |
| "0x040F4: BPTC (Broadcast packets tx count) 0x%08X\n", |
| regs_buff[109]); |
| |
| fprintf(stdout, |
| "0x040F8: TSCTC (TCP segment context tx count) 0x%08X\n", |
| regs_buff[110]); |
| |
| fprintf(stdout, |
| "0x04100: IAC (Interrupt assertion count) 0x%08X\n", |
| regs_buff[111]); |
| |
| fprintf(stdout, |
| "0x04104: RPTHC (Rx packets to host count) 0x%08X\n", |
| regs_buff[112]); |
| |
| fprintf(stdout, |
| "0x04118: HGPTC (Host good packets tx count) 0x%08X\n", |
| regs_buff[113]); |
| |
| fprintf(stdout, |
| "0x04128: HGORCL (Host good octets rx cnt lower) 0x%08X\n", |
| regs_buff[114]); |
| |
| fprintf(stdout, |
| "0x0412C: HGORCH (Host good octets rx cnt upper) 0x%08X\n", |
| regs_buff[115]); |
| |
| fprintf(stdout, |
| "0x04130: HGOTCL (Host good octets tx cnt lower) 0x%08X\n", |
| regs_buff[116]); |
| |
| fprintf(stdout, |
| "0x04134: HGOTCH (Host good octets tx cnt upper) 0x%08X\n", |
| regs_buff[117]); |
| |
| fprintf(stdout, |
| "0x04138: LENNERS (Length error count) 0x%08X\n", |
| regs_buff[118]); |
| |
| fprintf(stdout, |
| "0x04228: SCVPC (SerDes/SGMII code viol pkt cnt) 0x%08X\n", |
| regs_buff[119]); |
| |
| fprintf(stdout, |
| "0x0A018: HRMPC (Header redir missed pkt count) 0x%08X\n", |
| regs_buff[120]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: SRRCTL%d (Split and replic rx ctl%d) 0x%08X\n", |
| 0x0280C + (0x100 * i), i, i, regs_buff[121 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: PSRTYPE%d (Packet split receive type%d) 0x%08X\n", |
| 0x05480 + (0x4 * i), i, i, regs_buff[125 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: RDBAL%d (Rx desc base addr low%d) 0x%08X\n", |
| 0x02800 + (0x100 * i), i, i, regs_buff[129 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: RDBAH%d (Rx desc base addr high%d) 0x%08X\n", |
| 0x02804 + (0x100 * i), i, i, regs_buff[133 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: RDLEN%d (Rx descriptor length%d) 0x%08X\n", |
| 0x02808 + (0x100 * i), i, i, regs_buff[137 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: RDH%d (Rx descriptor head%d) 0x%08X\n", |
| 0x02810 + (0x100 * i), i, i, regs_buff[141 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: RDT%d (Rx descriptor tail%d) 0x%08X\n", |
| 0x02818 + (0x100 * i), i, i, regs_buff[145 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: RXDCTL%d (Rx descriptor control%d) 0x%08X\n", |
| 0x02828 + (0x100 * i), i, i, regs_buff[149 + i]); |
| |
| for (i = 0; i < 10; i++) |
| fprintf(stdout, |
| "0x0%02X: EITR%d (Interrupt throttle%d) 0x%08X\n", |
| 0x01680 + (0x4 * i), i, i, regs_buff[153 + i]); |
| |
| for (i = 0; i < 8; i++) |
| fprintf(stdout, |
| "0x0%02X: IMIR%d (Immediate interrupt Rx%d) 0x%08X\n", |
| 0x05A80 + (0x4 * i), i, i, regs_buff[163 + i]); |
| |
| for (i = 0; i < 8; i++) |
| fprintf(stdout, |
| "0x0%02X: IMIREXT%d (Immediate interr Rx extended%d) 0x%08X\n", |
| 0x05AA0 + (0x4 * i), i, i, regs_buff[171 + i]); |
| |
| for (i = 0; i < 16; i++) |
| fprintf(stdout, |
| "0x0%02X: RAL%02d (Receive address low%02d) 0x%08X\n", |
| 0x05400 + (0x8 * i), i,i, regs_buff[179 + i]); |
| |
| for (i = 0; i < 16; i++) |
| fprintf(stdout, |
| "0x0%02X: RAH%02d (Receive address high%02d) 0x%08X\n", |
| 0x05404 + (0x8 * i), i, i, regs_buff[195 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: TDBAL%d (Tx desc base address low%d) 0x%08X\n", |
| 0x03800 + (0x100 * i), i, i, regs_buff[211 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: TDBAH%d (Tx desc base address high%d) 0x%08X\n", |
| 0x03804 + (0x100 * i), i, i, regs_buff[215 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: TDLEN%d (Tx descriptor length%d) 0x%08X\n", |
| 0x03808 + (0x100 * i), i, i, regs_buff[219 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: TDH%d (Transmit descriptor head%d) 0x%08X\n", |
| 0x03810 + (0x100 * i), i, i, regs_buff[223 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: TDT%d (Transmit descriptor tail%d) 0x%08X\n", |
| 0x03818 + (0x100 * i), i, i, regs_buff[227 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: TXDCTL%d (Transmit descriptor control%d) 0x%08X\n", |
| 0x03828 + (0x100 * i), i, i, regs_buff[231 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: TDWBAL%d (Tx desc complete wb addr low%d) 0x%08X\n", |
| 0x03838 + (0x100 * i), i, i, regs_buff[235 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: TDWBAH%d (Tx desc complete wb addr hi%d) 0x%08X\n", |
| 0x0383C + (0x100 * i), i, i, regs_buff[239 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: DCA_TXCTRL%d (Tx DCA control%d) 0x%08X\n", |
| 0x03814 + (0x100 * i), i, i, regs_buff[243 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: IP4AT%d (IPv4 address table%d) 0x%08X\n", |
| 0x05840 + (0x8 * i), i, i, regs_buff[247 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: IP6AT%d (IPv6 address table%d) 0x%08X\n", |
| 0x05880 + (0x4 * i), i, i, regs_buff[251 + i]); |
| |
| for (i = 0; i < 32; i++) |
| fprintf(stdout, |
| "0x0%02X: WUPM%02d (Wake up packet memory%02d) 0x%08X\n", |
| 0x05A00 + (0x4 * i), i, i, regs_buff[255 + i]); |
| |
| for (i = 0; i < 128; i++) |
| fprintf(stdout, |
| "0x0%02X: FFMT%03d (Flexible filter mask table%03d) 0x%08X\n", |
| 0x09000 + (0x8 * i), i, i, regs_buff[287 + i]); |
| |
| for (i = 0; i < 128; i++) |
| fprintf(stdout, |
| "0x0%02X: FFVT%03d (Flexible filter value table%03d) 0x%08X\n", |
| 0x09800 + (0x8 * i), i, i, regs_buff[415 + i]); |
| |
| for (i = 0; i < 4; i++) |
| fprintf(stdout, |
| "0x0%02X: FFLT%d (Flexible filter length table%d) 0x%08X\n", |
| 0x05F00 + (0x8 * i), i, i, regs_buff[543 + i]); |
| |
| fprintf(stdout, |
| "0x03410: TDFH (Tx data FIFO head) 0x%08X\n", |
| regs_buff[547]); |
| |
| fprintf(stdout, |
| "0x03418: TDFT (Tx data FIFO tail) 0x%08X\n", |
| regs_buff[548]); |
| |
| fprintf(stdout, |
| "0x03420: TDFHS (Tx data FIFO head saved) 0x%08X\n", |
| regs_buff[549]); |
| |
| fprintf(stdout, |
| "0x03430: TDFPC (Tx data FIFO packet count) 0x%08X\n", |
| regs_buff[550]); |
| |
| return 0; |
| } |
| |