| What: /sys/bus/iio/devices/iio:deviceX | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Hardware chip or device accessed by one communication port. | |
| Corresponds to a grouping of sensor channels. X is the IIO | |
| index of the device. | |
| What: /sys/bus/iio/devices/triggerX | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| An event driven driver of data capture to an in kernel buffer. | |
| May be provided by a device driver that also has an IIO device | |
| based on hardware generated events (e.g. data ready) or | |
| provided by a separate driver for other hardware (e.g. | |
| periodic timer, GPIO or high resolution timer). | |
| Contains trigger type specific elements. These do not | |
| generalize well and hence are not documented in this file. | |
| X is the IIO index of the trigger. | |
| What: /sys/bus/iio/devices/iio:deviceX/buffer | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Directory of attributes relating to the buffer for the device. | |
| What: /sys/bus/iio/devices/iio:deviceX/name | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Description of the physical chip / device for device X. | |
| Typically a part number. | |
| What: /sys/bus/iio/devices/iio:deviceX/sampling_frequency | |
| What: /sys/bus/iio/devices/iio:deviceX/buffer/sampling_frequency | |
| What: /sys/bus/iio/devices/triggerX/sampling_frequency | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Some devices have internal clocks. This parameter sets the | |
| resulting sampling frequency. In many devices this | |
| parameter has an effect on input filters etc. rather than | |
| simply controlling when the input is sampled. As this | |
| effects data ready triggers, hardware buffers and the sysfs | |
| direct access interfaces, it may be found in any of the | |
| relevant directories. If it effects all of the above | |
| then it is to be found in the base device directory. | |
| What: /sys/bus/iio/devices/iio:deviceX/sampling_frequency_available | |
| What: /sys/.../iio:deviceX/buffer/sampling_frequency_available | |
| What: /sys/bus/iio/devices/triggerX/sampling_frequency_available | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| When the internal sampling clock can only take a small | |
| discrete set of values, this file lists those available. | |
| What: /sys/bus/iio/devices/iio:deviceX/oversampling_ratio | |
| KernelVersion: 2.6.38 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Hardware dependent ADC oversampling. Controls the sampling ratio | |
| of the digital filter if available. | |
| What: /sys/bus/iio/devices/iio:deviceX/oversampling_ratio_available | |
| KernelVersion: 2.6.38 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Hardware dependent values supported by the oversampling filter. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_raw | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Raw (unscaled no bias removal etc.) voltage measurement from | |
| channel Y. In special cases where the channel does not | |
| correspond to externally available input one of the named | |
| versions may be used. The number must always be specified and | |
| unique to allow association with event codes. Units after | |
| application of scale and offset are microvolts. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_voltageY-voltageZ_raw | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Raw (unscaled) differential voltage measurement equivalent to | |
| channel Y - channel Z where these channel numbers apply to the | |
| physically equivalent inputs when non differential readings are | |
| separately available. In differential only parts, then all that | |
| is required is a consistent labeling. Units after application | |
| of scale and offset are microvolts. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_capacitanceY_raw | |
| KernelVersion: 3.2 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Raw capacitance measurement from channel Y. Units after | |
| application of scale and offset are nanofarads. | |
| What: /sys/.../iio:deviceX/in_capacitanceY-in_capacitanceZ_raw | |
| KernelVersion: 3.2 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Raw differential capacitance measurement equivalent to | |
| channel Y - channel Z where these channel numbers apply to the | |
| physically equivalent inputs when non differential readings are | |
| separately available. In differential only parts, then all that | |
| is required is a consistent labeling. Units after application | |
| of scale and offset are nanofarads. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_temp_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_tempX_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_temp_x_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_temp_y_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_temp_z_raw | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Raw (unscaled no bias removal etc.) temperature measurement. | |
| If an axis is specified it generally means that the temperature | |
| sensor is associated with one part of a compound device (e.g. | |
| a gyroscope axis). Units after application of scale and offset | |
| are milli degrees Celsius. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_tempX_input | |
| KernelVersion: 2.6.38 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Scaled temperature measurement in milli degrees Celsius. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_raw | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Acceleration in direction x, y or z (may be arbitrarily assigned | |
| but should match other such assignments on device). | |
| Has all of the equivalent parameters as per voltageY. Units | |
| after application of scale and offset are m/s^2. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_x_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_y_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_z_raw | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Angular velocity about axis x, y or z (may be arbitrarily | |
| assigned). Has all the equivalent parameters as per voltageY. | |
| Units after application of scale and offset are radians per | |
| second. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_incli_x_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_incli_y_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_incli_z_raw | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Inclination raw reading about axis x, y or z (may be | |
| arbitrarily assigned). Data converted by application of offset | |
| and scale to degrees. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_magn_z_raw | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Magnetic field along axis x, y or z (may be arbitrarily | |
| assigned). Data converted by application of offset | |
| then scale to Gauss. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_peak_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_peak_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_peak_raw | |
| KernelVersion: 2.6.36 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Highest value since some reset condition. These | |
| attributes allow access to this and are otherwise | |
| the direct equivalent of the <type>Y[_name]_raw attributes. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_xyz_squared_peak_raw | |
| KernelVersion: 2.6.36 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| A computed peak value based on the sum squared magnitude of | |
| the underlying value in the specified directions. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/in_pressure_raw | |
| KernelVersion: 3.8 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Raw pressure measurement from channel Y. Units after | |
| application of scale and offset are kilopascal. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_offset | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_offset | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_offset | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_offset | |
| What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_offset | |
| What: /sys/bus/iio/devices/iio:deviceX/in_voltage_offset | |
| What: /sys/bus/iio/devices/iio:deviceX/in_tempY_offset | |
| What: /sys/bus/iio/devices/iio:deviceX/in_temp_offset | |
| What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_offset | |
| What: /sys/bus/iio/devices/iio:deviceX/in_pressure_offset | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| If known for a device, offset to be added to <type>[Y]_raw prior | |
| to scaling by <type>[Y]_scale in order to obtain value in the | |
| <type> units as specified in <type>[Y]_raw documentation. | |
| Not present if the offset is always 0 or unknown. If Y or | |
| axis <x|y|z> is not present, then the offset applies to all | |
| in channels of <type>. | |
| May be writable if a variable offset can be applied on the | |
| device. Note that this is different to calibbias which | |
| is for devices (or drivers) that apply offsets to compensate | |
| for variation between different instances of the part, typically | |
| adjusted by using some hardware supported calibration procedure. | |
| Calibbias is applied internally, offset is applied in userspace | |
| to the _raw output. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_voltage_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_peak_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_magn_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_magn_z_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_scale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_pressure_scale | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| If known for a device, scale to be applied to <type>Y[_name]_raw | |
| post addition of <type>[Y][_name]_offset in order to obtain the | |
| measured value in <type> units as specified in | |
| <type>[Y][_name]_raw documentation. If shared across all in | |
| channels then Y and <x|y|z> are not present and the value is | |
| called <type>[Y][_name]_scale. The peak modifier means this | |
| value is applied to <type>Y[_name]_peak_raw values. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_calibbias | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_calibbias | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_calibbias | |
| What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_x_calibbias | |
| What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_y_calibbias | |
| What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_z_calibbias | |
| What: /sys/bus/iio/devices/iio:deviceX/in_illuminance0_calibbias | |
| What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibbias | |
| What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibbias | |
| What: /sys/bus/iio/devices/iio:deviceX/in_pressure_calibbias | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Hardware applied calibration offset (assumed to fix production | |
| inaccuracies). | |
| What /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibscale | |
| What /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_calibscale | |
| What /sys/bus/iio/devices/iio:deviceX/in_voltage_calibscale | |
| What /sys/bus/iio/devices/iio:deviceX/in_accel_x_calibscale | |
| What /sys/bus/iio/devices/iio:deviceX/in_accel_y_calibscale | |
| What /sys/bus/iio/devices/iio:deviceX/in_accel_z_calibscale | |
| What /sys/bus/iio/devices/iio:deviceX/in_anglvel_x_calibscale | |
| What /sys/bus/iio/devices/iio:deviceX/in_anglvel_y_calibscale | |
| What /sys/bus/iio/devices/iio:deviceX/in_anglvel_z_calibscale | |
| what /sys/bus/iio/devices/iio:deviceX/in_illuminance0_calibscale | |
| what /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibscale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibscale | |
| What: /sys/bus/iio/devices/iio:deviceX/in_pressure_calibscale | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Hardware applied calibration scale factor (assumed to fix | |
| production inaccuracies). If shared across all channels, | |
| <type>_calibscale is used. | |
| What: /sys/bus/iio/devices/iio:deviceX/in_accel_scale_available | |
| What: /sys/.../iio:deviceX/in_voltageX_scale_available | |
| What: /sys/.../iio:deviceX/in_voltage-voltage_scale_available | |
| What: /sys/.../iio:deviceX/out_voltageX_scale_available | |
| What: /sys/.../iio:deviceX/out_altvoltageX_scale_available | |
| What: /sys/.../iio:deviceX/in_capacitance_scale_available | |
| What: /sys/.../iio:deviceX/in_pressure_scale_available | |
| What: /sys/.../iio:deviceX/in_pressureY_scale_available | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| If a discrete set of scale values is available, they | |
| are listed in this attribute. | |
| What /sys/bus/iio/devices/iio:deviceX/out_voltageY_hardwaregain | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Hardware applied gain factor. If shared across all channels, | |
| <type>_hardwaregain is used. | |
| What: /sys/.../in_accel_filter_low_pass_3db_frequency | |
| What: /sys/.../in_magn_filter_low_pass_3db_frequency | |
| What: /sys/.../in_anglvel_filter_low_pass_3db_frequency | |
| KernelVersion: 3.2 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| If a known or controllable low pass filter is applied | |
| to the underlying data channel, then this parameter | |
| gives the 3dB frequency of the filter in Hz. | |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_raw | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Raw (unscaled, no bias etc.) output voltage for | |
| channel Y. The number must always be specified and | |
| unique if the output corresponds to a single channel. | |
| While DAC like devices typically use out_voltage, | |
| a continuous frequency generating device, such as | |
| a DDS or PLL should use out_altvoltage. | |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY&Z_raw | |
| What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY&Z_raw | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Raw (unscaled, no bias etc.) output voltage for an aggregate of | |
| channel Y, channel Z, etc. This interface is available in cases | |
| where a single output sets the value for multiple channels | |
| simultaneously. | |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_powerdown_mode | |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltage_powerdown_mode | |
| What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_powerdown_mode | |
| What: /sys/bus/iio/devices/iio:deviceX/out_altvoltage_powerdown_mode | |
| KernelVersion: 2.6.38 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Specifies the output powerdown mode. | |
| DAC output stage is disconnected from the amplifier and | |
| 1kohm_to_gnd: connected to ground via an 1kOhm resistor, | |
| 6kohm_to_gnd: connected to ground via a 6kOhm resistor, | |
| 20kohm_to_gnd: connected to ground via a 20kOhm resistor, | |
| 100kohm_to_gnd: connected to ground via an 100kOhm resistor, | |
| three_state: left floating. | |
| For a list of available output power down options read | |
| outX_powerdown_mode_available. If Y is not present the | |
| mode is shared across all outputs. | |
| What: /sys/.../iio:deviceX/out_votlageY_powerdown_mode_available | |
| What: /sys/.../iio:deviceX/out_voltage_powerdown_mode_available | |
| What: /sys/.../iio:deviceX/out_altvotlageY_powerdown_mode_available | |
| What: /sys/.../iio:deviceX/out_altvoltage_powerdown_mode_available | |
| KernelVersion: 2.6.38 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Lists all available output power down modes. | |
| If Y is not present the mode is shared across all outputs. | |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_powerdown | |
| What: /sys/bus/iio/devices/iio:deviceX/out_voltage_powerdown | |
| What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_powerdown | |
| What: /sys/bus/iio/devices/iio:deviceX/out_altvoltage_powerdown | |
| KernelVersion: 2.6.38 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Writing 1 causes output Y to enter the power down mode specified | |
| by the corresponding outY_powerdown_mode. DAC output stage is | |
| disconnected from the amplifier. Clearing returns to normal | |
| operation. Y may be suppressed if all outputs are controlled | |
| together. | |
| What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_frequency | |
| KernelVersion: 3.4.0 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Output frequency for channel Y in Hz. The number must always be | |
| specified and unique if the output corresponds to a single | |
| channel. | |
| What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_phase | |
| KernelVersion: 3.4.0 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Phase in radians of one frequency/clock output Y | |
| (out_altvoltageY) relative to another frequency/clock output | |
| (out_altvoltageZ) of the device X. The number must always be | |
| specified and unique if the output corresponds to a single | |
| channel. | |
| What: /sys/bus/iio/devices/iio:deviceX/events | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Configuration of which hardware generated events are passed up | |
| to user-space. | |
| What: /sys/.../iio:deviceX/events/in_accel_x_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_accel_x_thresh_falling_en | |
| What: /sys/.../iio:deviceX/events/in_accel_y_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_accel_y_thresh_falling_en | |
| What: /sys/.../iio:deviceX/events/in_accel_z_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_accel_z_thresh_falling_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_x_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_x_thresh_falling_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_y_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_y_thresh_falling_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_z_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_z_thresh_falling_en | |
| What: /sys/.../iio:deviceX/events/in_magn_x_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_magn_x_thresh_falling_en | |
| What: /sys/.../iio:deviceX/events/in_magn_y_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_magn_y_thresh_falling_en | |
| What: /sys/.../iio:deviceX/events/in_magn_z_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_magn_z_thresh_falling_en | |
| What: /sys/.../iio:deviceX/events/in_voltageY_supply_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_voltageY_supply_thresh_falling_en | |
| What: /sys/.../iio:deviceX/events/in_voltageY_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_voltageY_thresh_falling_en | |
| What: /sys/.../iio:deviceX/events/in_tempY_thresh_rising_en | |
| What: /sys/.../iio:deviceX/events/in_tempY_thresh_falling_en | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Event generated when channel passes a threshold in the specified | |
| (_rising|_falling) direction. If the direction is not specified, | |
| then either the device will report an event which ever direction | |
| a single threshold value is passed in (e.g. | |
| <type>[Y][_name]_<raw|input>_thresh_value) or | |
| <type>[Y][_name]_<raw|input>_thresh_rising_value and | |
| <type>[Y][_name]_<raw|input>_thresh_falling_value may take | |
| different values, but the device can only enable both thresholds | |
| or neither. | |
| Note the driver will assume the last p events requested are | |
| to be enabled where p is how many it supports (which may vary | |
| depending on the exact set requested. So if you want to be | |
| sure you have set what you think you have, check the contents of | |
| these attributes after everything is configured. Drivers may | |
| have to buffer any parameters so that they are consistent when | |
| a given event type is enabled at a future point (and not those for | |
| whatever event was previously enabled). | |
| What: /sys/.../iio:deviceX/events/in_accel_x_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_accel_x_roc_falling_en | |
| What: /sys/.../iio:deviceX/events/in_accel_y_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_accel_y_roc_falling_en | |
| What: /sys/.../iio:deviceX/events/in_accel_z_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_accel_z_roc_falling_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_x_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_x_roc_falling_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_y_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_y_roc_falling_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_z_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_anglvel_z_roc_falling_en | |
| What: /sys/.../iio:deviceX/events/in_magn_x_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_magn_x_roc_falling_en | |
| What: /sys/.../iio:deviceX/events/in_magn_y_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_magn_y_roc_falling_en | |
| What: /sys/.../iio:deviceX/events/in_magn_z_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_magn_z_roc_falling_en | |
| What: /sys/.../iio:deviceX/events/in_voltageY_supply_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_voltageY_supply_roc_falling_en | |
| What: /sys/.../iio:deviceX/events/in_voltageY_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_voltageY_roc_falling_en | |
| What: /sys/.../iio:deviceX/events/in_tempY_roc_rising_en | |
| What: /sys/.../iio:deviceX/events/in_tempY_roc_falling_en | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Event generated when channel passes a threshold on the rate of | |
| change (1st differential) in the specified (_rising|_falling) | |
| direction. If the direction is not specified, then either the | |
| device will report an event which ever direction a single | |
| threshold value is passed in (e.g. | |
| <type>[Y][_name]_<raw|input>_roc_value) or | |
| <type>[Y][_name]_<raw|input>_roc_rising_value and | |
| <type>[Y][_name]_<raw|input>_roc_falling_value may take | |
| different values, but the device can only enable both rate of | |
| change thresholds or neither. | |
| Note the driver will assume the last p events requested are | |
| to be enabled where p is however many it supports (which may | |
| vary depending on the exact set requested. So if you want to be | |
| sure you have set what you think you have, check the contents of | |
| these attributes after everything is configured. Drivers may | |
| have to buffer any parameters so that they are consistent when | |
| a given event type is enabled a future point (and not those for | |
| whatever event was previously enabled). | |
| What: /sys/.../events/in_accel_x_raw_thresh_rising_value | |
| What: /sys/.../events/in_accel_x_raw_thresh_falling_value | |
| What: /sys/.../events/in_accel_y_raw_thresh_rising_value | |
| What: /sys/.../events/in_accel_y_raw_thresh_falling_value | |
| What: /sys/.../events/in_accel_z_raw_thresh_rising_value | |
| What: /sys/.../events/in_accel_z_raw_thresh_falling_value | |
| What: /sys/.../events/in_anglvel_x_raw_thresh_rising_value | |
| What: /sys/.../events/in_anglvel_x_raw_thresh_falling_value | |
| What: /sys/.../events/in_anglvel_y_raw_thresh_rising_value | |
| What: /sys/.../events/in_anglvel_y_raw_thresh_falling_value | |
| What: /sys/.../events/in_anglvel_z_raw_thresh_rising_value | |
| What: /sys/.../events/in_anglvel_z_raw_thresh_falling_value | |
| What: /sys/.../events/in_magn_x_raw_thresh_rising_value | |
| What: /sys/.../events/in_magn_x_raw_thresh_falling_value | |
| What: /sys/.../events/in_magn_y_raw_thresh_rising_value | |
| What: /sys/.../events/in_magn_y_raw_thresh_falling_value | |
| What: /sys/.../events/in_magn_z_raw_thresh_rising_value | |
| What: /sys/.../events/in_magn_z_raw_thresh_falling_value | |
| What: /sys/.../events/in_voltageY_supply_raw_thresh_rising_value | |
| What: /sys/.../events/in_voltageY_supply_raw_thresh_falling_value | |
| What: /sys/.../events/in_voltageY_raw_thresh_rising_value | |
| What: /sys/.../events/in_voltageY_raw_thresh_falling_value | |
| What: /sys/.../events/in_tempY_raw_thresh_rising_value | |
| What: /sys/.../events/in_tempY_raw_thresh_falling_value | |
| What: /sys/.../events/in_illuminance0_thresh_falling_value | |
| what: /sys/.../events/in_illuminance0_thresh_rising_value | |
| what: /sys/.../events/in_proximity0_thresh_falling_value | |
| what: /sys/.../events/in_proximity0_thresh_rising_value | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Specifies the value of threshold that the device is comparing | |
| against for the events enabled by | |
| <type>Y[_name]_thresh[_rising|falling]_en. | |
| If separate attributes exist for the two directions, but | |
| direction is not specified for this attribute, then a single | |
| threshold value applies to both directions. | |
| The raw or input element of the name indicates whether the | |
| value is in raw device units or in processed units (as _raw | |
| and _input do on sysfs direct channel read attributes). | |
| What: /sys/.../events/in_accel_x_raw_roc_rising_value | |
| What: /sys/.../events/in_accel_x_raw_roc_falling_value | |
| What: /sys/.../events/in_accel_y_raw_roc_rising_value | |
| What: /sys/.../events/in_accel_y_raw_roc_falling_value | |
| What: /sys/.../events/in_accel_z_raw_roc_rising_value | |
| What: /sys/.../events/in_accel_z_raw_roc_falling_value | |
| What: /sys/.../events/in_anglvel_x_raw_roc_rising_value | |
| What: /sys/.../events/in_anglvel_x_raw_roc_falling_value | |
| What: /sys/.../events/in_anglvel_y_raw_roc_rising_value | |
| What: /sys/.../events/in_anglvel_y_raw_roc_falling_value | |
| What: /sys/.../events/in_anglvel_z_raw_roc_rising_value | |
| What: /sys/.../events/in_anglvel_z_raw_roc_falling_value | |
| What: /sys/.../events/in_magn_x_raw_roc_rising_value | |
| What: /sys/.../events/in_magn_x_raw_roc_falling_value | |
| What: /sys/.../events/in_magn_y_raw_roc_rising_value | |
| What: /sys/.../events/in_magn_y_raw_roc_falling_value | |
| What: /sys/.../events/in_magn_z_raw_roc_rising_value | |
| What: /sys/.../events/in_magn_z_raw_roc_falling_value | |
| What: /sys/.../events/in_voltageY_supply_raw_roc_rising_value | |
| What: /sys/.../events/in_voltageY_supply_raw_roc_falling_value | |
| What: /sys/.../events/in_voltageY_raw_roc_rising_value | |
| What: /sys/.../events/in_voltageY_raw_roc_falling_value | |
| What: /sys/.../events/in_tempY_raw_roc_rising_value | |
| What: /sys/.../events/in_tempY_raw_roc_falling_value | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Specifies the value of rate of change threshold that the | |
| device is comparing against for the events enabled by | |
| <type>[Y][_name]_roc[_rising|falling]_en. | |
| If separate attributes exist for the two directions, | |
| but direction is not specified for this attribute, | |
| then a single threshold value applies to both directions. | |
| The raw or input element of the name indicates whether the | |
| value is in raw device units or in processed units (as _raw | |
| and _input do on sysfs direct channel read attributes). | |
| What: /sys/.../events/in_accel_x_thresh_rising_period | |
| What: /sys/.../events/in_accel_x_thresh_falling_period | |
| hat: /sys/.../events/in_accel_x_roc_rising_period | |
| What: /sys/.../events/in_accel_x_roc_falling_period | |
| What: /sys/.../events/in_accel_y_thresh_rising_period | |
| What: /sys/.../events/in_accel_y_thresh_falling_period | |
| What: /sys/.../events/in_accel_y_roc_rising_period | |
| What: /sys/.../events/in_accel_y_roc_falling_period | |
| What: /sys/.../events/in_accel_z_thresh_rising_period | |
| What: /sys/.../events/in_accel_z_thresh_falling_period | |
| What: /sys/.../events/in_accel_z_roc_rising_period | |
| What: /sys/.../events/in_accel_z_roc_falling_period | |
| What: /sys/.../events/in_anglvel_x_thresh_rising_period | |
| What: /sys/.../events/in_anglvel_x_thresh_falling_period | |
| What: /sys/.../events/in_anglvel_x_roc_rising_period | |
| What: /sys/.../events/in_anglvel_x_roc_falling_period | |
| What: /sys/.../events/in_anglvel_y_thresh_rising_period | |
| What: /sys/.../events/in_anglvel_y_thresh_falling_period | |
| What: /sys/.../events/in_anglvel_y_roc_rising_period | |
| What: /sys/.../events/in_anglvel_y_roc_falling_period | |
| What: /sys/.../events/in_anglvel_z_thresh_rising_period | |
| What: /sys/.../events/in_anglvel_z_thresh_falling_period | |
| What: /sys/.../events/in_anglvel_z_roc_rising_period | |
| What: /sys/.../events/in_anglvel_z_roc_falling_period | |
| What: /sys/.../events/in_magn_x_thresh_rising_period | |
| What: /sys/.../events/in_magn_x_thresh_falling_period | |
| What: /sys/.../events/in_magn_x_roc_rising_period | |
| What: /sys/.../events/in_magn_x_roc_falling_period | |
| What: /sys/.../events/in_magn_y_thresh_rising_period | |
| What: /sys/.../events/in_magn_y_thresh_falling_period | |
| What: /sys/.../events/in_magn_y_roc_rising_period | |
| What: /sys/.../events/in_magn_y_roc_falling_period | |
| What: /sys/.../events/in_magn_z_thresh_rising_period | |
| What: /sys/.../events/in_magn_z_thresh_falling_period | |
| What: /sys/.../events/in_magn_z_roc_rising_period | |
| What: /sys/.../events/in_magn_z_roc_falling_period | |
| What: /sys/.../events/in_voltageY_supply_thresh_rising_period | |
| What: /sys/.../events/in_voltageY_supply_thresh_falling_period | |
| What: /sys/.../events/in_voltageY_supply_roc_rising_period | |
| What: /sys/.../events/in_voltageY_supply_roc_falling_period | |
| What: /sys/.../events/in_voltageY_thresh_rising_period | |
| What: /sys/.../events/in_voltageY_thresh_falling_period | |
| What: /sys/.../events/in_voltageY_roc_rising_period | |
| What: /sys/.../events/in_voltageY_roc_falling_period | |
| What: /sys/.../events/in_tempY_thresh_rising_period | |
| What: /sys/.../events/in_tempY_thresh_falling_period | |
| What: /sys/.../events/in_tempY_roc_rising_period | |
| What: /sys/.../events/in_tempY_roc_falling_period | |
| What: /sys/.../events/in_accel_x&y&z_mag_falling_period | |
| What: /sys/.../events/in_intensity0_thresh_period | |
| What: /sys/.../events/in_proximity0_thresh_period | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Period of time (in seconds) for which the condition must be | |
| met before an event is generated. If direction is not | |
| specified then this period applies to both directions. | |
| What: /sys/.../iio:deviceX/events/in_accel_mag_en | |
| What: /sys/.../iio:deviceX/events/in_accel_mag_rising_en | |
| What: /sys/.../iio:deviceX/events/in_accel_mag_falling_en | |
| What: /sys/.../iio:deviceX/events/in_accel_x_mag_en | |
| What: /sys/.../iio:deviceX/events/in_accel_x_mag_rising_en | |
| What: /sys/.../iio:deviceX/events/in_accel_x_mag_falling_en | |
| What: /sys/.../iio:deviceX/events/in_accel_y_mag_en | |
| What: /sys/.../iio:deviceX/events/in_accel_y_mag_rising_en | |
| What: /sys/.../iio:deviceX/events/in_accel_y_mag_falling_en | |
| What: /sys/.../iio:deviceX/events/in_accel_z_mag_en | |
| What: /sys/.../iio:deviceX/events/in_accel_z_mag_rising_en | |
| What: /sys/.../iio:deviceX/events/in_accel_z_mag_falling_en | |
| What: /sys/.../iio:deviceX/events/in_accel_x&y&z_mag_rising_en | |
| What: /sys/.../iio:deviceX/events/in_accel_x&y&z_mag_falling_en | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Similar to in_accel_x_thresh[_rising|_falling]_en, but here the | |
| magnitude of the channel is compared to the threshold, not its | |
| signed value. | |
| What: /sys/.../events/in_accel_raw_mag_value | |
| What: /sys/.../events/in_accel_x_raw_mag_rising_value | |
| What: /sys/.../events/in_accel_y_raw_mag_rising_value | |
| What: /sys/.../events/in_accel_z_raw_mag_rising_value | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| The value to which the magnitude of the channel is compared. If | |
| number or direction is not specified, applies to all channels of | |
| this type. | |
| What: /sys/bus/iio/devices/iio:deviceX/trigger/current_trigger | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| The name of the trigger source being used, as per string given | |
| in /sys/class/iio/triggerY/name. | |
| What: /sys/bus/iio/devices/iio:deviceX/buffer/length | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Number of scans contained by the buffer. | |
| What: /sys/bus/iio/devices/iio:deviceX/buffer/bytes_per_datum | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Bytes per scan. Due to alignment fun, the scan may be larger | |
| than implied directly by the scan_element parameters. | |
| What: /sys/bus/iio/devices/iio:deviceX/buffer/enable | |
| KernelVersion: 2.6.35 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Actually start the buffer capture up. Will start trigger | |
| if first device and appropriate. | |
| What: /sys/bus/iio/devices/iio:deviceX/buffer/scan_elements | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Directory containing interfaces for elements that will be | |
| captured for a single triggered sample set in the buffer. | |
| What: /sys/.../buffer/scan_elements/in_accel_x_en | |
| What: /sys/.../buffer/scan_elements/in_accel_y_en | |
| What: /sys/.../buffer/scan_elements/in_accel_z_en | |
| What: /sys/.../buffer/scan_elements/in_anglvel_x_en | |
| What: /sys/.../buffer/scan_elements/in_anglvel_y_en | |
| What: /sys/.../buffer/scan_elements/in_anglvel_z_en | |
| What: /sys/.../buffer/scan_elements/in_magn_x_en | |
| What: /sys/.../buffer/scan_elements/in_magn_y_en | |
| What: /sys/.../buffer/scan_elements/in_magn_z_en | |
| What: /sys/.../buffer/scan_elements/in_timestamp_en | |
| What: /sys/.../buffer/scan_elements/in_voltageY_supply_en | |
| What: /sys/.../buffer/scan_elements/in_voltageY_en | |
| What: /sys/.../buffer/scan_elements/in_voltageY-voltageZ_en | |
| What: /sys/.../buffer/scan_elements/in_incli_x_en | |
| What: /sys/.../buffer/scan_elements/in_incli_y_en | |
| What: /sys/.../buffer/scan_elements/in_pressureY_en | |
| What: /sys/.../buffer/scan_elements/in_pressure_en | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Scan element control for triggered data capture. | |
| What: /sys/.../buffer/scan_elements/in_accel_type | |
| What: /sys/.../buffer/scan_elements/in_anglvel_type | |
| What: /sys/.../buffer/scan_elements/in_magn_type | |
| What: /sys/.../buffer/scan_elements/in_incli_type | |
| What: /sys/.../buffer/scan_elements/in_voltageY_type | |
| What: /sys/.../buffer/scan_elements/in_voltage_type | |
| What: /sys/.../buffer/scan_elements/in_voltageY_supply_type | |
| What: /sys/.../buffer/scan_elements/in_timestamp_type | |
| What: /sys/.../buffer/scan_elements/in_pressureY_type | |
| What: /sys/.../buffer/scan_elements/in_pressure_type | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| Description of the scan element data storage within the buffer | |
| and hence the form in which it is read from user-space. | |
| Form is [be|le]:[s|u]bits/storagebits[>>shift]. | |
| be or le specifies big or little endian. s or u specifies if | |
| signed (2's complement) or unsigned. bits is the number of bits | |
| of data and storagebits is the space (after padding) that it | |
| occupies in the buffer. shift if specified, is the shift that | |
| needs to be applied prior to masking out unused bits. Some | |
| devices put their data in the middle of the transferred elements | |
| with additional information on both sides. Note that some | |
| devices will have additional information in the unused bits | |
| so to get a clean value, the bits value must be used to mask | |
| the buffer output value appropriately. The storagebits value | |
| also specifies the data alignment. So s48/64>>2 will be a | |
| signed 48 bit integer stored in a 64 bit location aligned to | |
| a 64 bit boundary. To obtain the clean value, shift right 2 | |
| and apply a mask to zero the top 16 bits of the result. | |
| For other storage combinations this attribute will be extended | |
| appropriately. | |
| What: /sys/.../buffer/scan_elements/in_accel_type_available | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| If the type parameter can take one of a small set of values, | |
| this attribute lists them. | |
| What: /sys/.../buffer/scan_elements/in_voltageY_index | |
| What: /sys/.../buffer/scan_elements/in_voltageY_supply_index | |
| What: /sys/.../buffer/scan_elements/in_accel_x_index | |
| What: /sys/.../buffer/scan_elements/in_accel_y_index | |
| What: /sys/.../buffer/scan_elements/in_accel_z_index | |
| What: /sys/.../buffer/scan_elements/in_anglvel_x_index | |
| What: /sys/.../buffer/scan_elements/in_anglvel_y_index | |
| What: /sys/.../buffer/scan_elements/in_anglvel_z_index | |
| What: /sys/.../buffer/scan_elements/in_magn_x_index | |
| What: /sys/.../buffer/scan_elements/in_magn_y_index | |
| What: /sys/.../buffer/scan_elements/in_magn_z_index | |
| What: /sys/.../buffer/scan_elements/in_incli_x_index | |
| What: /sys/.../buffer/scan_elements/in_incli_y_index | |
| What: /sys/.../buffer/scan_elements/in_timestamp_index | |
| What: /sys/.../buffer/scan_elements/in_pressureY_index | |
| What: /sys/.../buffer/scan_elements/in_pressure_index | |
| KernelVersion: 2.6.37 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| A single positive integer specifying the position of this | |
| scan element in the buffer. Note these are not dependent on | |
| what is enabled and may not be contiguous. Thus for user-space | |
| to establish the full layout these must be used in conjunction | |
| with all _en attributes to establish which channels are present, | |
| and the relevant _type attributes to establish the data storage | |
| format. | |
| What: /sys/.../iio:deviceX/in_anglvel_z_quadrature_correction_raw | |
| KernelVersion: 2.6.38 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| This attribute is used to read the amount of quadrature error | |
| present in the device at a given time. | |
| What: /sys/.../iio:deviceX/in_intensity_red_integration_time | |
| What: /sys/.../iio:deviceX/in_intensity_green_integration_time | |
| What: /sys/.../iio:deviceX/in_intensity_blue_integration_time | |
| What: /sys/.../iio:deviceX/in_intensity_clear_integration_time | |
| What: /sys/.../iio:deviceX/in_illuminance_integration_time | |
| KernelVersion: 3.12 | |
| Contact: linux-iio@vger.kernel.org | |
| Description: | |
| This attribute is used to get/set the integration time in | |
| seconds. |