blob: 2409c300ed1441e6660fbd8475ae3e5ee01023f4 [file] [log] [blame]
/*
* U-boot - cpu.c CPU specific functions
*
* Copyright (c) 2005-2008 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* Licensed under the GPL-2 or later.
*/
#include <common.h>
#include <command.h>
#include <asm/blackfin.h>
#include <asm/cplb.h>
#include <asm/mach-common/bits/core.h>
#include <asm/mach-common/bits/ebiu.h>
#include <asm/mach-common/bits/trace.h>
#include <asm/serial.h>
#include "cpu.h"
#include "initcode.h"
ulong bfin_poweron_retx;
#if defined(CONFIG_CORE1_RUN) && defined(COREB_L1_CODE_START)
void bfin_core1_start(void)
{
#ifdef BF561_FAMILY
/* Enable core 1 */
bfin_write_SYSCR(bfin_read_SYSCR() & ~0x0020);
#else
/* Enable core 1 */
bfin_write32(RCU0_SVECT1, COREB_L1_CODE_START);
bfin_write32(RCU0_CRCTL, 0);
bfin_write32(RCU0_CRCTL, 0x2);
/* Check if core 1 starts */
while (!(bfin_read32(RCU0_CRSTAT) & 0x2))
continue;
bfin_write32(RCU0_CRCTL, 0);
/* flag to notify cces core 1 application */
bfin_write32(SDU0_MSG_SET, (1 << 19));
#endif
}
#endif
__attribute__ ((__noreturn__))
void cpu_init_f(ulong bootflag, ulong loaded_from_ldr)
{
#ifndef CONFIG_BFIN_BOOTROM_USES_EVT1
/* Build a NOP slide over the LDR jump block. Whee! */
char nops[0xC];
serial_early_puts("NOP Slide\n");
memset(nops, 0x00, sizeof(nops));
memcpy((void *)L1_INST_SRAM, nops, sizeof(nops));
#endif
if (!loaded_from_ldr) {
/* Relocate sections into L1 if the LDR didn't do it -- don't
* check length because the linker script does the size
* checking at build time.
*/
serial_early_puts("L1 Relocate\n");
extern char _stext_l1[], _text_l1_lma[], _text_l1_len[];
memcpy(&_stext_l1, &_text_l1_lma, (unsigned long)_text_l1_len);
extern char _sdata_l1[], _data_l1_lma[], _data_l1_len[];
memcpy(&_sdata_l1, &_data_l1_lma, (unsigned long)_data_l1_len);
}
/*
* Make sure our async settings are committed. Some bootroms
* (like the BF537) will reset some registers on us after it
* has finished loading the LDR. Or if we're booting over
* JTAG, the initcode never got a chance to run. Or if we
* aren't booting from parallel flash, the initcode skipped
* this step completely.
*/
program_async_controller(NULL);
/* Save RETX so we can pass it while booting Linux */
bfin_poweron_retx = bootflag;
#ifdef CONFIG_DEBUG_DUMP
/* Turn on hardware trace buffer */
bfin_write_TBUFCTL(TBUFPWR | TBUFEN);
#endif
#ifndef CONFIG_PANIC_HANG
/* Reset upon a double exception rather than just hanging.
* Do not do bfin_read on SWRST as that will reset status bits.
*/
# ifdef SWRST
bfin_write_SWRST(DOUBLE_FAULT);
# endif
#endif
#if defined(CONFIG_CORE1_RUN) && defined(COREB_L1_CODE_START)
bfin_core1_start();
#endif
serial_early_puts("Board init flash\n");
board_init_f(bootflag);
/* should not be reached */
while (1);
}
int exception_init(void)
{
bfin_write_EVT3(trap);
return 0;
}
int irq_init(void)
{
#ifdef SIC_IMASK0
bfin_write_SIC_IMASK0(0);
bfin_write_SIC_IMASK1(0);
# ifdef SIC_IMASK2
bfin_write_SIC_IMASK2(0);
# endif
#elif defined(SICA_IMASK0)
bfin_write_SICA_IMASK0(0);
bfin_write_SICA_IMASK1(0);
#elif defined(SIC_IMASK)
bfin_write_SIC_IMASK(0);
#endif
/* Set up a dummy NMI handler if needed. */
if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS || ANOMALY_05000219)
bfin_write_EVT2(evt_nmi); /* NMI */
bfin_write_EVT5(evt_default); /* hardware error */
bfin_write_EVT6(evt_default); /* core timer */
bfin_write_EVT7(evt_default);
bfin_write_EVT8(evt_default);
bfin_write_EVT9(evt_default);
bfin_write_EVT10(evt_default);
bfin_write_EVT11(evt_default);
bfin_write_EVT12(evt_default);
bfin_write_EVT13(evt_default);
bfin_write_EVT14(evt_default);
bfin_write_EVT15(evt_default);
bfin_write_ILAT(0);
CSYNC();
/* enable hardware error irq */
irq_flags = 0x3f;
local_irq_enable();
return 0;
}