blob: 61e778ea5f5d4379fb5b84b2de444f8243145725 [file] [log] [blame]
#
# GDB Init script for the Coldfire 5272 processor.
#
# The main purpose of this script is to configure the
# DRAM controller so code can be loaded.
#
# This file was changed to suite the senTec COBRA5272 board.
#
define addresses
set $mbar = 0x10000001
set $scr = $mbar - 1 + 0x004
set $spr = $mbar - 1 + 0x006
set $pmr = $mbar - 1 + 0x008
set $apmr = $mbar - 1 + 0x00e
set $dir = $mbar - 1 + 0x010
set $icr1 = $mbar - 1 + 0x020
set $icr2 = $mbar - 1 + 0x024
set $icr3 = $mbar - 1 + 0x028
set $icr4 = $mbar - 1 + 0x02c
set $isr = $mbar - 1 + 0x030
set $pitr = $mbar - 1 + 0x034
set $piwr = $mbar - 1 + 0x038
set $pivr = $mbar - 1 + 0x03f
set $csbr0 = $mbar - 1 + 0x040
set $csor0 = $mbar - 1 + 0x044
set $csbr1 = $mbar - 1 + 0x048
set $csor1 = $mbar - 1 + 0x04c
set $csbr2 = $mbar - 1 + 0x050
set $csor2 = $mbar - 1 + 0x054
set $csbr3 = $mbar - 1 + 0x058
set $csor3 = $mbar - 1 + 0x05c
set $csbr4 = $mbar - 1 + 0x060
set $csor4 = $mbar - 1 + 0x064
set $csbr5 = $mbar - 1 + 0x068
set $csor5 = $mbar - 1 + 0x06c
set $csbr6 = $mbar - 1 + 0x070
set $csor6 = $mbar - 1 + 0x074
set $csbr7 = $mbar - 1 + 0x078
set $csor7 = $mbar - 1 + 0x07c
set $pacnt = $mbar - 1 + 0x080
set $paddr = $mbar - 1 + 0x084
set $padat = $mbar - 1 + 0x086
set $pbcnt = $mbar - 1 + 0x088
set $pbddr = $mbar - 1 + 0x08c
set $pbdat = $mbar - 1 + 0x08e
set $pcddr = $mbar - 1 + 0x094
set $pcdat = $mbar - 1 + 0x096
set $pdcnt = $mbar - 1 + 0x098
set $sdcr = $mbar - 1 + 0x180
set $sdtr = $mbar - 1 + 0x184
set $wrrr = $mbar - 1 + 0x280
set $wirr = $mbar - 1 + 0x283
set $wcr = $mbar - 1 + 0x288
set $wer = $mbar - 1 + 0x28c
end
#
# Setup system configuration
#
define setup-sys
set *((unsigned short *) $scr) = 0x0003
set *((unsigned short *) $spr) = 0xffff
set *((unsigned char *) $pivr) = 0x4f
end
#
# Setup Chip Selects (as per Motorola M5272C3 board)
#
define setup-cs
# CS0 -- FLASH
set *((unsigned long *) $csbr0) = 0xffe00201
set *((unsigned long *) $csor0) = 0xffe00014
# CS1 -- external bus test
set *((unsigned long *) $csbr1) = 0x0
set *((unsigned long *) $csor1) = 0x0
# CS2 -- Optional FSRAM
set *((unsigned long *) $csbr2) = 0x30000001
set *((unsigned long *) $csor2) = 0xfff80000
# CS3 -- not used
set *((unsigned long *) $csbr3) = 0x0
set *((unsigned long *) $csor3) = 0x0
# CS4 -- not used
set *((unsigned long *) $csbr4) = 0x0
set *((unsigned long *) $csor4) = 0x0
# CS5 -- PLI socket0
set *((unsigned long *) $csbr5) = 0x0
set *((unsigned long *) $csor5) = 0x0
# CS6 -- PLI socket1
set *((unsigned long *) $csbr6) = 0x0
set *((unsigned long *) $csor6) = 0x0
# CS7 -- SDRAM
set *((unsigned long *) $csbr7) = 0x00000701
set *((unsigned long *) $csor7) = 0xff00007c
end
#
# Setup the DRAM controller.
#
define setup-dram
set *((unsigned long *) $sdtr) = 0x0000f539
set *((unsigned long *) $sdcr) = 0x00004211
# Dummy write to start SDRAM
set *((unsigned long *) 0) = 0
end
#
# Setup for GPIO pins
#
define setup-ppio
# PORT A -- the LED's
set *((unsigned long *) $pacnt) = 0x00000000
# lower 8 bits for output:
set *((unsigned short *) $paddr) = 0xff
# LED's off:
set *((unsigned short *) $padat) = 0xff
# PORT B
set *((unsigned long *) $pbcnt) = 0x55554155
set *((unsigned short *) $pbddr) = 0x0000
set *((unsigned short *) $pbdat) = 0x17ea
# PORT C
#set *((unsigned short *) $pcddr) = 0x0000
#set *((unsigned short *) $pcdat) = 0x1898
# PORT D
set *((unsigned long *) $pdcnt) = 0x00000000
end
#
# Added for uClinux-coldfire target...
#
target bdm /dev/bdm
addresses
setup-sys
setup-cs
setup-dram
setup-ppio
set print pretty
set print asm-demangle
display/i $pc
#
load u-boot
set $pc=0x20000
c