blob: ffd66478b194180e10db2649b96dee8280f77751 [file] [log] [blame] [edit]
/*
* Common SPI Interface: Controller-specific definitions
*
* (C) Copyright 2001
* Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _SPI_H_
#define _SPI_H_
/* SPI mode flags */
#define SPI_CPHA 0x01 /* clock phase */
#define SPI_CPOL 0x02 /* clock polarity */
#define SPI_MODE_0 (0|0) /* (original MicroWire) */
#define SPI_MODE_1 (0|SPI_CPHA)
#define SPI_MODE_2 (SPI_CPOL|0)
#define SPI_MODE_3 (SPI_CPOL|SPI_CPHA)
#define SPI_CS_HIGH 0x04 /* CS active high */
#define SPI_LSB_FIRST 0x08 /* per-word bits-on-wire */
#define SPI_3WIRE 0x10 /* SI/SO signals shared */
#define SPI_LOOP 0x20 /* loopback mode */
#define SPI_SLAVE 0x40 /* slave mode */
#define SPI_PREAMBLE 0x80 /* Skip preamble bytes */
/* SPI transfer flags */
#define SPI_XFER_BEGIN 0x01 /* Assert CS before transfer */
#define SPI_XFER_END 0x02 /* Deassert CS after transfer */
#define SPI_XFER_MMAP 0x08 /* Memory Mapped start */
#define SPI_XFER_MMAP_END 0x10 /* Memory Mapped End */
#define SPI_XFER_ONCE (SPI_XFER_BEGIN | SPI_XFER_END)
#define SPI_XFER_U_PAGE (1 << 5)
/* SPI TX operation modes */
#define SPI_OPM_TX_QPP 1 << 0
/* SPI RX operation modes */
#define SPI_OPM_RX_AS 1 << 0
#define SPI_OPM_RX_DOUT 1 << 1
#define SPI_OPM_RX_DIO 1 << 2
#define SPI_OPM_RX_QOF 1 << 3
#define SPI_OPM_RX_QIOF 1 << 4
#define SPI_OPM_RX_EXTN SPI_OPM_RX_AS | SPI_OPM_RX_DOUT | \
SPI_OPM_RX_DIO | SPI_OPM_RX_QOF | \
SPI_OPM_RX_QIOF
/* SPI bus connection options */
#define SPI_CONN_DUAL_SHARED 1 << 0
#define SPI_CONN_DUAL_SEPARATED 1 << 1
/* Header byte that marks the start of the message */
#define SPI_PREAMBLE_END_BYTE 0xec
#define SPI_DEFAULT_WORDLEN 8
/**
* struct spi_slave - Representation of a SPI slave
*
* Drivers are expected to extend this with controller-specific data.
*
* @bus: ID of the bus that the slave is attached to.
* @cs: ID of the chip select connected to the slave.
* @op_mode_rx: SPI RX operation mode.
* @op_mode_tx: SPI TX operation mode.
* @wordlen: Size of SPI word in number of bits
* @max_write_size: If non-zero, the maximum number of bytes which can
* be written at once, excluding command bytes.
* @memory_map: Address of read-only SPI flash access.
* @option: Varies SPI bus options - separate, shared bus.
* @flags: Indication of SPI flags.
*/
struct spi_slave {
unsigned int bus;
unsigned int cs;
u8 op_mode_rx;
u8 op_mode_tx;
unsigned int wordlen;
unsigned int max_write_size;
void *memory_map;
u8 option;
u8 flags;
};
/**
* Initialization, must be called once on start up.
*
* TODO: I don't think we really need this.
*/
void spi_init(void);
/**
* spi_do_alloc_slave - Allocate a new SPI slave (internal)
*
* Allocate and zero all fields in the spi slave, and set the bus/chip
* select. Use the helper macro spi_alloc_slave() to call this.
*
* @offset: Offset of struct spi_slave within slave structure.
* @size: Size of slave structure.
* @bus: Bus ID of the slave chip.
* @cs: Chip select ID of the slave chip on the specified bus.
*/
void *spi_do_alloc_slave(int offset, int size, unsigned int bus,
unsigned int cs);
/**
* spi_alloc_slave - Allocate a new SPI slave
*
* Allocate and zero all fields in the spi slave, and set the bus/chip
* select.
*
* @_struct: Name of structure to allocate (e.g. struct tegra_spi).
* This structure must contain a member 'struct spi_slave *slave'.
* @bus: Bus ID of the slave chip.
* @cs: Chip select ID of the slave chip on the specified bus.
*/
#define spi_alloc_slave(_struct, bus, cs) \
spi_do_alloc_slave(offsetof(_struct, slave), \
sizeof(_struct), bus, cs)
/**
* spi_alloc_slave_base - Allocate a new SPI slave with no private data
*
* Allocate and zero all fields in the spi slave, and set the bus/chip
* select.
*
* @bus: Bus ID of the slave chip.
* @cs: Chip select ID of the slave chip on the specified bus.
*/
#define spi_alloc_slave_base(bus, cs) \
spi_do_alloc_slave(0, sizeof(struct spi_slave), bus, cs)
/**
* Set up communications parameters for a SPI slave.
*
* This must be called once for each slave. Note that this function
* usually doesn't touch any actual hardware, it only initializes the
* contents of spi_slave so that the hardware can be easily
* initialized later.
*
* @bus: Bus ID of the slave chip.
* @cs: Chip select ID of the slave chip on the specified bus.
* @max_hz: Maximum SCK rate in Hz.
* @mode: Clock polarity, clock phase and other parameters.
*
* Returns: A spi_slave reference that can be used in subsequent SPI
* calls, or NULL if one or more of the parameters are not supported.
*/
struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
unsigned int max_hz, unsigned int mode);
/**
* Free any memory associated with a SPI slave.
*
* @slave: The SPI slave
*/
void spi_free_slave(struct spi_slave *slave);
/**
* Claim the bus and prepare it for communication with a given slave.
*
* This must be called before doing any transfers with a SPI slave. It
* will enable and initialize any SPI hardware as necessary, and make
* sure that the SCK line is in the correct idle state. It is not
* allowed to claim the same bus for several slaves without releasing
* the bus in between.
*
* @slave: The SPI slave
*
* Returns: 0 if the bus was claimed successfully, or a negative value
* if it wasn't.
*/
int spi_claim_bus(struct spi_slave *slave);
/**
* Release the SPI bus
*
* This must be called once for every call to spi_claim_bus() after
* all transfers have finished. It may disable any SPI hardware as
* appropriate.
*
* @slave: The SPI slave
*/
void spi_release_bus(struct spi_slave *slave);
/**
* Set the word length for SPI transactions
*
* Set the word length (number of bits per word) for SPI transactions.
*
* @slave: The SPI slave
* @wordlen: The number of bits in a word
*
* Returns: 0 on success, -1 on failure.
*/
int spi_set_wordlen(struct spi_slave *slave, unsigned int wordlen);
/**
* SPI transfer
*
* This writes "bitlen" bits out the SPI MOSI port and simultaneously clocks
* "bitlen" bits in the SPI MISO port. That's just the way SPI works.
*
* The source of the outgoing bits is the "dout" parameter and the
* destination of the input bits is the "din" parameter. Note that "dout"
* and "din" can point to the same memory location, in which case the
* input data overwrites the output data (since both are buffered by
* temporary variables, this is OK).
*
* spi_xfer() interface:
* @slave: The SPI slave which will be sending/receiving the data.
* @bitlen: How many bits to write and read.
* @dout: Pointer to a string of bits to send out. The bits are
* held in a byte array and are sent MSB first.
* @din: Pointer to a string of bits that will be filled in.
* @flags: A bitwise combination of SPI_XFER_* flags.
*
* Returns: 0 on success, not 0 on failure
*/
int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
void *din, unsigned long flags);
/**
* Determine if a SPI chipselect is valid.
* This function is provided by the board if the low-level SPI driver
* needs it to determine if a given chipselect is actually valid.
*
* Returns: 1 if bus:cs identifies a valid chip on this board, 0
* otherwise.
*/
int spi_cs_is_valid(unsigned int bus, unsigned int cs);
/**
* Activate a SPI chipselect.
* This function is provided by the board code when using a driver
* that can't control its chipselects automatically (e.g.
* common/soft_spi.c). When called, it should activate the chip select
* to the device identified by "slave".
*/
void spi_cs_activate(struct spi_slave *slave);
/**
* Deactivate a SPI chipselect.
* This function is provided by the board code when using a driver
* that can't control its chipselects automatically (e.g.
* common/soft_spi.c). When called, it should deactivate the chip
* select to the device identified by "slave".
*/
void spi_cs_deactivate(struct spi_slave *slave);
/**
* Set transfer speed.
* This sets a new speed to be applied for next spi_xfer().
* @slave: The SPI slave
* @hz: The transfer speed
*/
void spi_set_speed(struct spi_slave *slave, uint hz);
/**
* Write 8 bits, then read 8 bits.
* @slave: The SPI slave we're communicating with
* @byte: Byte to be written
*
* Returns: The value that was read, or a negative value on error.
*
* TODO: This function probably shouldn't be inlined.
*/
static inline int spi_w8r8(struct spi_slave *slave, unsigned char byte)
{
unsigned char dout[2];
unsigned char din[2];
int ret;
dout[0] = byte;
dout[1] = 0;
ret = spi_xfer(slave, 16, dout, din, SPI_XFER_BEGIN | SPI_XFER_END);
return ret < 0 ? ret : din[1];
}
/**
* Set up a SPI slave for a particular device tree node
*
* This calls spi_setup_slave() with the correct bus number. Call
* spi_free_slave() to free it later.
*
* @param blob: Device tree blob
* @param slave_node: Slave node to use
* @param spi_node: SPI peripheral node to use
* @return pointer to new spi_slave structure
*/
struct spi_slave *spi_setup_slave_fdt(const void *blob, int slave_node,
int spi_node);
/**
* spi_base_setup_slave_fdt() - helper function to set up a SPI slace
*
* This decodes SPI properties from the slave node to determine the
* chip select and SPI parameters.
*
* @blob: Device tree blob
* @busnum: Bus number to use
* @node: Device tree node for the SPI bus
*/
struct spi_slave *spi_base_setup_slave_fdt(const void *blob, int busnum,
int node);
#endif /* _SPI_H_ */