| # | |
| # FDDI network device configuration | |
| # | |
| config FDDI | |
| tristate "FDDI driver support" | |
| depends on PCI || EISA || TC | |
| ---help--- | |
| Fiber Distributed Data Interface is a high speed local area network | |
| design; essentially a replacement for high speed Ethernet. FDDI can | |
| run over copper or fiber. If you are connected to such a network and | |
| want a driver for the FDDI card in your computer, say Y here (and | |
| then also Y to the driver for your FDDI card, below). Most people | |
| will say N. | |
| if FDDI | |
| config DEFXX | |
| tristate "Digital DEFTA/DEFEA/DEFPA adapter support" | |
| depends on FDDI && (PCI || EISA || TC) | |
| ---help--- | |
| This is support for the DIGITAL series of TURBOchannel (DEFTA), | |
| EISA (DEFEA) and PCI (DEFPA) controllers which can connect you | |
| to a local FDDI network. | |
| To compile this driver as a module, choose M here: the module | |
| will be called defxx. If unsure, say N. | |
| config DEFXX_MMIO | |
| bool | |
| prompt "Use MMIO instead of PIO" if PCI || EISA | |
| depends on DEFXX | |
| default n if PCI || EISA | |
| default y | |
| ---help--- | |
| This instructs the driver to use EISA or PCI memory-mapped I/O | |
| (MMIO) as appropriate instead of programmed I/O ports (PIO). | |
| Enabling this gives an improvement in processing time in parts | |
| of the driver, but it may cause problems with EISA (DEFEA) | |
| adapters. TURBOchannel does not have the concept of I/O ports, | |
| so MMIO is always used for these (DEFTA) adapters. | |
| If unsure, say N. | |
| config SKFP | |
| tristate "SysKonnect FDDI PCI support" | |
| depends on FDDI && PCI | |
| select BITREVERSE | |
| ---help--- | |
| Say Y here if you have a SysKonnect FDDI PCI adapter. | |
| The following adapters are supported by this driver: | |
| - SK-5521 (SK-NET FDDI-UP) | |
| - SK-5522 (SK-NET FDDI-UP DAS) | |
| - SK-5541 (SK-NET FDDI-FP) | |
| - SK-5543 (SK-NET FDDI-LP) | |
| - SK-5544 (SK-NET FDDI-LP DAS) | |
| - SK-5821 (SK-NET FDDI-UP64) | |
| - SK-5822 (SK-NET FDDI-UP64 DAS) | |
| - SK-5841 (SK-NET FDDI-FP64) | |
| - SK-5843 (SK-NET FDDI-LP64) | |
| - SK-5844 (SK-NET FDDI-LP64 DAS) | |
| - Netelligent 100 FDDI DAS Fibre SC | |
| - Netelligent 100 FDDI SAS Fibre SC | |
| - Netelligent 100 FDDI DAS UTP | |
| - Netelligent 100 FDDI SAS UTP | |
| - Netelligent 100 FDDI SAS Fibre MIC | |
| Read <file:Documentation/networking/skfp.txt> for information about | |
| the driver. | |
| Questions concerning this driver can be addressed to: | |
| <linux@syskonnect.de> | |
| To compile this driver as a module, choose M here: the module | |
| will be called skfp. This is recommended. | |
| endif # FDDI |