blob: f0a0c174695ec433a71fed34921d77fb28513375 [file] [log] [blame]
/*
* (C) Copyright 2002-2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2002
* Sysgo Real-Time Solutions, GmbH <www.elinos.com>
* Marius Groeger <mgroeger@sysgo.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* To match the U-Boot user interface on ARM platforms to the U-Boot
* standard (as on PPC platforms), some messages with debug character
* are removed from the default U-Boot build.
*
* Define DEBUG here if you want additional info as shown below
* printed upon startup:
*
* U-Boot code: 00F00000 -> 00F3C774 BSS: -> 00FC3274
* IRQ Stack: 00ebff7c
* FIQ Stack: 00ebef7c
*/
#include <common.h>
#include <command.h>
#include <environment.h>
#include <malloc.h>
#include <stdio_dev.h>
#include <version.h>
#include <net.h>
#include <serial.h>
#include <nand.h>
#include <onenand_uboot.h>
#include <mmc.h>
#include <scsi.h>
#include <libfdt.h>
#include <fdtdec.h>
#include <post.h>
#include <logbuff.h>
#include <asm/sections.h>
#ifdef CONFIG_BITBANGMII
#include <miiphy.h>
#endif
#ifdef CONFIG_FASTBOOT
#include <fastboot.h>
#endif
DECLARE_GLOBAL_DATA_PTR;
ulong monitor_flash_len;
#ifdef CONFIG_HAS_DATAFLASH
extern int AT91F_DataflashInit(void);
extern void dataflash_print_info(void);
#endif
#if defined(CONFIG_HARD_I2C) || \
defined(CONFIG_SYS_I2C)
#include <i2c.h>
#endif
/************************************************************************
* Coloured LED functionality
************************************************************************
* May be supplied by boards if desired
*/
inline void __coloured_LED_init(void) {}
void coloured_LED_init(void)
__attribute__((weak, alias("__coloured_LED_init")));
inline void __red_led_on(void) {}
void red_led_on(void) __attribute__((weak, alias("__red_led_on")));
inline void __red_led_off(void) {}
void red_led_off(void) __attribute__((weak, alias("__red_led_off")));
inline void __green_led_on(void) {}
void green_led_on(void) __attribute__((weak, alias("__green_led_on")));
inline void __green_led_off(void) {}
void green_led_off(void) __attribute__((weak, alias("__green_led_off")));
inline void __yellow_led_on(void) {}
void yellow_led_on(void) __attribute__((weak, alias("__yellow_led_on")));
inline void __yellow_led_off(void) {}
void yellow_led_off(void) __attribute__((weak, alias("__yellow_led_off")));
inline void __blue_led_on(void) {}
void blue_led_on(void) __attribute__((weak, alias("__blue_led_on")));
inline void __blue_led_off(void) {}
void blue_led_off(void) __attribute__((weak, alias("__blue_led_off")));
/*
************************************************************************
* Init Utilities *
************************************************************************
* Some of this code should be moved into the core functions,
* or dropped completely,
* but let's get it working (again) first...
*/
#if defined(CONFIG_ARM_DCC) && !defined(CONFIG_BAUDRATE)
#define CONFIG_BAUDRATE 115200
#endif
static int init_baudrate(void)
{
gd->baudrate = getenv_ulong("baudrate", 10, CONFIG_BAUDRATE);
return 0;
}
static int display_banner(void)
{
printf("\n\n%s\n\n", version_string);
debug("U-Boot code: %08lX -> %08lX BSS: -> %08lX\n",
(ulong)&_start,
(ulong)&__bss_start, (ulong)&__bss_end);
#ifdef CONFIG_MODEM_SUPPORT
debug("Modem Support enabled\n");
#endif
#ifdef CONFIG_USE_IRQ
debug("IRQ Stack: %08lx\n", IRQ_STACK_START);
debug("FIQ Stack: %08lx\n", FIQ_STACK_START);
#endif
return (0);
}
/*
* WARNING: this code looks "cleaner" than the PowerPC version, but
* has the disadvantage that you either get nothing, or everything.
* On PowerPC, you might see "DRAM: " before the system hangs - which
* gives a simple yet clear indication which part of the
* initialization if failing.
*/
static int display_dram_config(void)
{
int i;
#ifdef DEBUG
puts("RAM Configuration:\n");
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
printf("Bank #%d: %08lx ", i, gd->bd->bi_dram[i].start);
print_size(gd->bd->bi_dram[i].size, "\n");
}
#else
ulong size = 0;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
size += gd->bd->bi_dram[i].size;
puts("DRAM: ");
print_size(size, "\n");
#endif
return (0);
}
#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
static int init_func_i2c(void)
{
puts("I2C: ");
#ifdef CONFIG_SYS_I2C
i2c_init_all();
#else
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
#endif
puts("ready\n");
return (0);
}
#endif
#if defined(CONFIG_CMD_PCI) || defined (CONFIG_PCI)
#include <pci.h>
static int arm_pci_init(void)
{
pci_init();
return 0;
}
#endif /* CONFIG_CMD_PCI || CONFIG_PCI */
/*
* Breathe some life into the board...
*
* Initialize a serial port as console, and carry out some hardware
* tests.
*
* The first part of initialization is running from Flash memory;
* its main purpose is to initialize the RAM so that we
* can relocate the monitor code to RAM.
*/
/*
* All attempts to come up with a "common" initialization sequence
* that works for all boards and architectures failed: some of the
* requirements are just _too_ different. To get rid of the resulting
* mess of board dependent #ifdef'ed code we now make the whole
* initialization sequence configurable to the user.
*
* The requirements for any new initalization function is simple: it
* receives a pointer to the "global data" structure as it's only
* argument, and returns an integer return code, where 0 means
* "continue" and != 0 means "fatal error, hang the system".
*/
typedef int (init_fnc_t) (void);
void __dram_init_banksize(void)
{
gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
gd->bd->bi_dram[0].size = gd->ram_size;
}
void dram_init_banksize(void)
__attribute__((weak, alias("__dram_init_banksize")));
int __arch_cpu_init(void)
{
return 0;
}
int arch_cpu_init(void)
__attribute__((weak, alias("__arch_cpu_init")));
int __power_init_board(void)
{
return 0;
}
int power_init_board(void)
__attribute__((weak, alias("__power_init_board")));
/* Record the board_init_f() bootstage (after arch_cpu_init()) */
static int mark_bootstage(void)
{
bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_F, "board_init_f");
return 0;
}
init_fnc_t *init_sequence[] = {
arch_cpu_init, /* basic arch cpu dependent setup */
mark_bootstage,
#ifdef CONFIG_OF_CONTROL
fdtdec_check_fdt,
#endif
#if defined(CONFIG_BOARD_EARLY_INIT_F)
board_early_init_f,
#endif
timer_init, /* initialize timer */
#ifdef CONFIG_BOARD_POSTCLK_INIT
board_postclk_init,
#endif
#ifdef CONFIG_FSL_ESDHC
get_clocks,
#endif
env_init, /* initialize environment */
init_baudrate, /* initialze baudrate settings */
serial_init, /* serial communications setup */
console_init_f, /* stage 1 init of console */
display_banner, /* say that we are here */
print_cpuinfo, /* display cpu info (and speed) */
#if defined(CONFIG_DISPLAY_BOARDINFO)
checkboard, /* display board info */
#endif
#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
init_func_i2c,
#endif
dram_init, /* configure available RAM banks */
NULL,
};
void board_init_f(ulong bootflag)
{
bd_t *bd;
init_fnc_t **init_fnc_ptr;
gd_t *id;
ulong addr, addr_sp;
#ifdef CONFIG_PRAM
ulong reg;
#endif
void *new_fdt = NULL;
size_t fdt_size = 0;
memset((void *)gd, 0, sizeof(gd_t));
gd->mon_len = (ulong)&__bss_end - (ulong)_start;
#ifdef CONFIG_OF_EMBED
/* Get a pointer to the FDT */
gd->fdt_blob = __dtb_dt_begin;
#elif defined CONFIG_OF_SEPARATE
/* FDT is at end of image */
gd->fdt_blob = &_end;
#endif
/* Allow the early environment to override the fdt address */
gd->fdt_blob = (void *)getenv_ulong("fdtcontroladdr", 16,
(uintptr_t)gd->fdt_blob);
for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) {
if ((*init_fnc_ptr)() != 0) {
hang ();
}
}
#ifdef CONFIG_OF_CONTROL
/* For now, put this check after the console is ready */
if (fdtdec_prepare_fdt()) {
panic("** CONFIG_OF_CONTROL defined but no FDT - please see "
"doc/README.fdt-control");
}
#endif
debug("monitor len: %08lX\n", gd->mon_len);
/*
* Ram is setup, size stored in gd !!
*/
debug("ramsize: %08lX\n", gd->ram_size);
#if defined(CONFIG_SYS_MEM_TOP_HIDE)
/*
* Subtract specified amount of memory to hide so that it won't
* get "touched" at all by U-Boot. By fixing up gd->ram_size
* the Linux kernel should now get passed the now "corrected"
* memory size and won't touch it either. This should work
* for arch/ppc and arch/powerpc. Only Linux board ports in
* arch/powerpc with bootwrapper support, that recalculate the
* memory size from the SDRAM controller setup will have to
* get fixed.
*/
gd->ram_size -= CONFIG_SYS_MEM_TOP_HIDE;
#endif
addr = CONFIG_SYS_SDRAM_BASE + get_effective_memsize();
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* reserve kernel log buffer */
addr -= (LOGBUFF_RESERVE);
debug("Reserving %dk for kernel logbuffer at %08lx\n", LOGBUFF_LEN,
addr);
#endif
#endif
#ifdef CONFIG_PRAM
/*
* reserve protected RAM
*/
reg = getenv_ulong("pram", 10, CONFIG_PRAM);
addr -= (reg << 10); /* size is in kB */
debug("Reserving %ldk for protected RAM at %08lx\n", reg, addr);
#endif /* CONFIG_PRAM */
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
/* reserve TLB table */
gd->arch.tlb_size = PGTABLE_SIZE;
addr -= gd->arch.tlb_size;
/* round down to next 64 kB limit */
addr &= ~(0x10000 - 1);
gd->arch.tlb_addr = addr;
debug("TLB table from %08lx to %08lx\n", addr, addr + gd->arch.tlb_size);
#endif
/* round down to next 4 kB limit */
addr &= ~(4096 - 1);
debug("Top of RAM usable for U-Boot at: %08lx\n", addr);
#ifdef CONFIG_LCD
#ifdef CONFIG_FB_ADDR
gd->fb_base = CONFIG_FB_ADDR;
#else
/* reserve memory for LCD display (always full pages) */
addr = lcd_setmem(addr);
gd->fb_base = addr;
#endif /* CONFIG_FB_ADDR */
#endif /* CONFIG_LCD */
/*
* reserve memory for U-Boot code, data & bss
* round down to next 4 kB limit
*/
addr -= gd->mon_len;
addr &= ~(4096 - 1);
debug("Reserving %ldk for U-Boot at: %08lx\n", gd->mon_len >> 10, addr);
#ifndef CONFIG_SPL_BUILD
/*
* reserve memory for malloc() arena
*/
addr_sp = addr - TOTAL_MALLOC_LEN;
debug("Reserving %dk for malloc() at: %08lx\n",
TOTAL_MALLOC_LEN >> 10, addr_sp);
/*
* (permanently) allocate a Board Info struct
* and a permanent copy of the "global" data
*/
addr_sp -= sizeof (bd_t);
bd = (bd_t *) addr_sp;
gd->bd = bd;
debug("Reserving %zu Bytes for Board Info at: %08lx\n",
sizeof (bd_t), addr_sp);
#ifdef CONFIG_MACH_TYPE
gd->bd->bi_arch_number = CONFIG_MACH_TYPE; /* board id for Linux */
#endif
addr_sp -= sizeof (gd_t);
id = (gd_t *) addr_sp;
debug("Reserving %zu Bytes for Global Data at: %08lx\n",
sizeof (gd_t), addr_sp);
#if defined(CONFIG_OF_SEPARATE) && defined(CONFIG_OF_CONTROL)
/*
* If the device tree is sitting immediate above our image then we
* must relocate it. If it is embedded in the data section, then it
* will be relocated with other data.
*/
if (gd->fdt_blob) {
fdt_size = ALIGN(fdt_totalsize(gd->fdt_blob) + 0x1000, 32);
addr_sp -= fdt_size;
new_fdt = (void *)addr_sp;
debug("Reserving %zu Bytes for FDT at: %08lx\n",
fdt_size, addr_sp);
}
#endif
#ifndef CONFIG_ARM64
/* setup stackpointer for exeptions */
gd->irq_sp = addr_sp;
#ifdef CONFIG_USE_IRQ
addr_sp -= (CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ);
debug("Reserving %zu Bytes for IRQ stack at: %08lx\n",
CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ, addr_sp);
#endif
/* leave 3 words for abort-stack */
addr_sp -= 12;
/* 8-byte alignment for ABI compliance */
addr_sp &= ~0x07;
#else /* CONFIG_ARM64 */
/* 16-byte alignment for ABI compliance */
addr_sp &= ~0x0f;
#endif /* CONFIG_ARM64 */
#else
addr_sp += 128; /* leave 32 words for abort-stack */
gd->irq_sp = addr_sp;
#endif
debug("New Stack Pointer is: %08lx\n", addr_sp);
#ifdef CONFIG_POST
post_bootmode_init();
post_run(NULL, POST_ROM | post_bootmode_get(0));
#endif
gd->bd->bi_baudrate = gd->baudrate;
/* Ram ist board specific, so move it to board code ... */
dram_init_banksize();
display_dram_config(); /* and display it */
gd->relocaddr = addr;
gd->start_addr_sp = addr_sp;
gd->reloc_off = addr - (ulong)&_start;
debug("relocation Offset is: %08lx\n", gd->reloc_off);
if (new_fdt) {
memcpy(new_fdt, gd->fdt_blob, fdt_size);
gd->fdt_blob = new_fdt;
}
memcpy(id, (void *)gd, sizeof(gd_t));
}
#if !defined(CONFIG_SYS_NO_FLASH)
static char *failed = "*** failed ***\n";
#endif
/*
* Tell if it's OK to load the environment early in boot.
*
* If CONFIG_OF_CONFIG is defined, we'll check with the FDT to see
* if this is OK (defaulting to saying it's not OK).
*
* NOTE: Loading the environment early can be a bad idea if security is
* important, since no verification is done on the environment.
*
* @return 0 if environment should not be loaded, !=0 if it is ok to load
*/
static int should_load_env(void)
{
#ifdef CONFIG_OF_CONTROL
return fdtdec_get_config_int(gd->fdt_blob, "load-environment", 1);
#elif defined CONFIG_DELAY_ENVIRONMENT
return 0;
#else
return 1;
#endif
}
#if defined(CONFIG_DISPLAY_BOARDINFO_LATE) && defined(CONFIG_OF_CONTROL)
static void display_fdt_model(const void *blob)
{
const char *model;
model = (char *)fdt_getprop(blob, 0, "model", NULL);
printf("Model: %s\n", model ? model : "<unknown>");
}
#endif
/************************************************************************
*
* This is the next part if the initialization sequence: we are now
* running from RAM and have a "normal" C environment, i. e. global
* data can be written, BSS has been cleared, the stack size in not
* that critical any more, etc.
*
************************************************************************
*/
void board_init_r(gd_t *id, ulong dest_addr)
{
ulong malloc_start;
#if !defined(CONFIG_SYS_NO_FLASH)
ulong flash_size;
#endif
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_R, "board_init_r");
monitor_flash_len = (ulong)&__rel_dyn_end - (ulong)_start;
/* Enable caches */
enable_caches();
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects */
/*
* TODO: printing of the clock inforamtion of the board is now
* implemented as part of bdinfo command. Currently only support for
* davinci SOC's is added. Remove this check once all the board
* implement this.
*/
#ifdef CONFIG_CLOCKS
set_cpu_clk_info(); /* Setup clock information */
#endif
serial_initialize();
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is immediately below the monitor copy in DRAM */
malloc_start = dest_addr - TOTAL_MALLOC_LEN;
mem_malloc_init (malloc_start, TOTAL_MALLOC_LEN);
#ifdef CONFIG_ARCH_EARLY_INIT_R
arch_early_init_r();
#endif
power_init_board();
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
flash_size = flash_init();
if (flash_size > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
if (getenv_yesno("flashchecksum") == 1) {
printf(" CRC: %08X", crc32(0,
(const unsigned char *) CONFIG_SYS_FLASH_BASE,
flash_size));
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
#endif
#if defined(CONFIG_CMD_NAND)
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#if defined(CONFIG_CMD_ONENAND)
onenand_init();
#endif
#ifdef CONFIG_GENERIC_MMC
puts("MMC: ");
mmc_initialize(gd->bd);
#endif
#ifdef CONFIG_CMD_SCSI
puts("SCSI: ");
scsi_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
if (should_load_env())
env_relocate();
else
set_default_env(NULL);
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
#endif
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#ifdef CONFIG_DISPLAY_BOARDINFO_LATE
# ifdef CONFIG_OF_CONTROL
/* Put this here so it appears on the LCD, now it is ready */
display_fdt_model(gd->fdt_blob);
# else
checkboard();
# endif
#endif
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
#ifdef CONFIG_BOARD_LATE_INIT
board_late_init();
#endif
#ifdef CONFIG_FASTBOOT
fastboot_setup();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
puts("Net: ");
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram = 0;
uchar memsz[32];
#ifdef CONFIG_PRAM
pram = getenv_ulong("pram", 10, CONFIG_PRAM);
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf((char *)memsz, "%ldk", (gd->ram_size / 1024) - pram);
setenv("mem", (char *)memsz);
}
#endif
#ifdef CONFIG_FASTBOOT
check_fastboot();
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
main_loop();
}
/* NOTREACHED - no way out of command loop except booting */
}