| config SIBYTE_SB1250 | |
| bool | |
| select CEVT_SB1250 | |
| select CSRC_SB1250 | |
| select HW_HAS_PCI | |
| select IRQ_CPU | |
| select SIBYTE_ENABLE_LDT_IF_PCI | |
| select SIBYTE_HAS_ZBUS_PROFILING | |
| select SIBYTE_SB1xxx_SOC | |
| select SYS_SUPPORTS_SMP | |
| config SIBYTE_BCM1120 | |
| bool | |
| select CEVT_SB1250 | |
| select CSRC_SB1250 | |
| select IRQ_CPU | |
| select SIBYTE_BCM112X | |
| select SIBYTE_HAS_ZBUS_PROFILING | |
| select SIBYTE_SB1xxx_SOC | |
| config SIBYTE_BCM1125 | |
| bool | |
| select CEVT_SB1250 | |
| select CSRC_SB1250 | |
| select HW_HAS_PCI | |
| select IRQ_CPU | |
| select SIBYTE_BCM112X | |
| select SIBYTE_HAS_ZBUS_PROFILING | |
| select SIBYTE_SB1xxx_SOC | |
| config SIBYTE_BCM1125H | |
| bool | |
| select CEVT_SB1250 | |
| select CSRC_SB1250 | |
| select HW_HAS_PCI | |
| select IRQ_CPU | |
| select SIBYTE_BCM112X | |
| select SIBYTE_ENABLE_LDT_IF_PCI | |
| select SIBYTE_HAS_ZBUS_PROFILING | |
| select SIBYTE_SB1xxx_SOC | |
| config SIBYTE_BCM112X | |
| bool | |
| select CEVT_SB1250 | |
| select CSRC_SB1250 | |
| select IRQ_CPU | |
| select SIBYTE_SB1xxx_SOC | |
| select SIBYTE_HAS_ZBUS_PROFILING | |
| config SIBYTE_BCM1x80 | |
| bool | |
| select CEVT_BCM1480 | |
| select CSRC_BCM1480 | |
| select HW_HAS_PCI | |
| select IRQ_CPU | |
| select SIBYTE_HAS_ZBUS_PROFILING | |
| select SIBYTE_SB1xxx_SOC | |
| select SYS_SUPPORTS_SMP | |
| config SIBYTE_BCM1x55 | |
| bool | |
| select CEVT_BCM1480 | |
| select CSRC_BCM1480 | |
| select HW_HAS_PCI | |
| select IRQ_CPU | |
| select SIBYTE_SB1xxx_SOC | |
| select SIBYTE_HAS_ZBUS_PROFILING | |
| select SYS_SUPPORTS_SMP | |
| config SIBYTE_SB1xxx_SOC | |
| bool | |
| select DMA_COHERENT | |
| select IRQ_CPU | |
| select SWAP_IO_SPACE | |
| select SYS_SUPPORTS_32BIT_KERNEL | |
| select SYS_SUPPORTS_64BIT_KERNEL | |
| select FW_CFE | |
| select SYS_HAS_EARLY_PRINTK | |
| choice | |
| prompt "SiByte SOC Stepping" | |
| depends on SIBYTE_SB1xxx_SOC | |
| config CPU_SB1_PASS_1 | |
| bool "1250 Pass1" | |
| depends on SIBYTE_SB1250 | |
| select CPU_HAS_PREFETCH | |
| config CPU_SB1_PASS_2_1250 | |
| bool "1250 An" | |
| depends on SIBYTE_SB1250 | |
| select CPU_SB1_PASS_2 | |
| help | |
| Also called BCM1250 Pass 2 | |
| config CPU_SB1_PASS_2_2 | |
| bool "1250 Bn" | |
| depends on SIBYTE_SB1250 | |
| select CPU_HAS_PREFETCH | |
| help | |
| Also called BCM1250 Pass 2.2 | |
| config CPU_SB1_PASS_4 | |
| bool "1250 Cn" | |
| depends on SIBYTE_SB1250 | |
| select CPU_HAS_PREFETCH | |
| help | |
| Also called BCM1250 Pass 3 | |
| config CPU_SB1_PASS_2_112x | |
| bool "112x Hybrid" | |
| depends on SIBYTE_BCM112X | |
| select CPU_SB1_PASS_2 | |
| config CPU_SB1_PASS_3 | |
| bool "112x An" | |
| depends on SIBYTE_BCM112X | |
| select CPU_HAS_PREFETCH | |
| endchoice | |
| config CPU_SB1_PASS_2 | |
| bool | |
| config SIBYTE_HAS_LDT | |
| bool | |
| config SIBYTE_ENABLE_LDT_IF_PCI | |
| bool | |
| select SIBYTE_HAS_LDT if PCI | |
| config SB1_CEX_ALWAYS_FATAL | |
| bool "All cache exceptions considered fatal (no recovery attempted)" | |
| depends on SIBYTE_SB1xxx_SOC | |
| config SB1_CERR_STALL | |
| bool "Stall (rather than panic) on fatal cache error" | |
| depends on SIBYTE_SB1xxx_SOC | |
| config SIBYTE_CFE_CONSOLE | |
| bool "Use firmware console" | |
| depends on SIBYTE_SB1xxx_SOC | |
| help | |
| Use the CFE API's console write routines during boot. Other console | |
| options (VT console, sb1250 duart console, etc.) should not be | |
| configured. | |
| config SIBYTE_BUS_WATCHER | |
| bool "Support for Bus Watcher statistics" | |
| depends on SIBYTE_SB1xxx_SOC | |
| help | |
| Handle and keep statistics on the bus error interrupts (COR_ECC, | |
| BAD_ECC, IO_BUS). | |
| config SIBYTE_BW_TRACE | |
| bool "Capture bus trace before bus error" | |
| depends on SIBYTE_BUS_WATCHER | |
| help | |
| Run a continuous bus trace, dumping the raw data as soon as | |
| a ZBbus error is detected. Cannot work if ZBbus profiling | |
| is turned on, and also will interfere with JTAG-based trace | |
| buffer activity. Raw buffer data is dumped to console, and | |
| must be processed off-line. | |
| config SIBYTE_TBPROF | |
| tristate "Support for ZBbus profiling" | |
| depends on SIBYTE_HAS_ZBUS_PROFILING | |
| config SIBYTE_HAS_ZBUS_PROFILING | |
| bool |