u-boot-imx/board/csb472/csb472.c

/*
 * (C) Copyright 2004
 * Tolunay Orkun, Nextio Inc., torkun@nextio.com
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <asm/processor.h>
#include <i2c.h>
#include <miiphy.h>
#include <asm/ppc4xx-emac.h>

void sdram_init(void);

/*
 * board_early_init_f: do early board initialization
 *
 */
int board_early_init_f(void)
{
   /*-------------------------------------------------------------------------+
   | Interrupt controller setup for the Walnut board.
   | Note: IRQ 0-15  405GP internally generated; active high; level sensitive
   |       IRQ 16    405GP internally generated; active low; level sensitive
   |       IRQ 17-24 RESERVED
   |       IRQ 25 (EXT IRQ 0) FPGA; active high; level sensitive
   |       IRQ 26 (EXT IRQ 1) SMI; active high; level sensitive
   |       IRQ 27 (EXT IRQ 2) Not Used
   |       IRQ 28 (EXT IRQ 3) PCI SLOT 3; active low; level sensitive
   |       IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive
   |       IRQ 30 (EXT IRQ 5) PCI SLOT 1; active low; level sensitive
   |       IRQ 31 (EXT IRQ 6) PCI SLOT 0; active low; level sensitive
   | Note for Walnut board:
   |       An interrupt taken for the FPGA (IRQ 25) indicates that either
   |       the Mouse, Keyboard, IRDA, or External Expansion caused the
   |       interrupt. The FPGA must be read to determine which device
   |       caused the interrupt. The default setting of the FPGA clears
   |
   +-------------------------------------------------------------------------*/

	mtdcr (UIC0SR, 0xFFFFFFFF);   /* clear all ints */
	mtdcr (UIC0ER, 0x00000000);   /* disable all ints */
	mtdcr (UIC0CR, 0x00000000);   /* set all to be non-critical */
	mtdcr (UIC0PR, 0xFFFFFF83);   /* set int polarities */
	mtdcr (UIC0TR, 0x10000000);   /* set int trigger levels */
	mtdcr (UIC0VCR, 0x00000001);  /* set vect base=0,INT0 highest priority */
	mtdcr (UIC0SR, 0xFFFFFFFF);   /* clear all ints */

	mtebc (EBC0_CFG, 0xa8400000);   /* EBC always driven */

	return 0; /* success */
}

/*
 * checkboard: identify/verify the board we are running
 *
 * Remark: we just assume it is correct board here!
 *
 */
int checkboard(void)
{
	printf("BOARD: Cogent CSB472\n");

	return 0; /* success */
}

/*
 * initram: Determine the size of mounted DRAM
 *
 * Size is determined by reading SDRAM configuration registers as
 * configured by initialization code
 *
 */
phys_size_t initdram (int board_type)
{
	ulong tot_size;
	ulong bank_size;
	ulong tmp;

	/*
	 * ToDo: Move the asm init routine sdram_init() to this C file,
	 * or even better use some common ppc4xx code available
	 * in arch/powerpc/cpu/ppc4xx
	 */
	sdram_init();

	tot_size = 0;

	mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
	tmp = mfdcr (SDRAM0_CFGDATA);
	if (tmp & 0x00000001) {
		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
		tot_size += bank_size;
	}

	mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
	tmp = mfdcr (SDRAM0_CFGDATA);
	if (tmp & 0x00000001) {
		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
		tot_size += bank_size;
	}

	mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
	tmp = mfdcr (SDRAM0_CFGDATA);
	if (tmp & 0x00000001) {
		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
		tot_size += bank_size;
	}

	mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
	tmp = mfdcr (SDRAM0_CFGDATA);
	if (tmp & 0x00000001) {
		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
		tot_size += bank_size;
	}

	return tot_size;
}

/*
 * last_stage_init: final configurations (such as PHY etc)
 *
 */
int last_stage_init(void)
{
	/* initialize the PHY */
	miiphy_reset("ppc_4xx_eth0", CONFIG_PHY_ADDR);

	/* AUTO neg */
	miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_BMCR,
			BMCR_ANENABLE | BMCR_ANRESTART);

	/* LEDs     */
	miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_NWAYTEST, 0x0d08);

	return 0; /* success */
}