| # | |
| # Physical Layer USB driver configuration | |
| # | |
| menu "USB Physical Layer drivers" | |
| config USB_PHY | |
| def_bool n | |
| # | |
| # USB Transceiver Drivers | |
| # | |
| config AB8500_USB | |
| tristate "AB8500 USB Transceiver Driver" | |
| depends on AB8500_CORE | |
| select USB_PHY | |
| help | |
| Enable this to support the USB OTG transceiver in AB8500 chip. | |
| This transceiver supports high and full speed devices plus, | |
| in host mode, low speed. | |
| config FSL_USB2_OTG | |
| bool "Freescale USB OTG Transceiver Driver" | |
| depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM_RUNTIME | |
| select USB_OTG | |
| select USB_PHY | |
| help | |
| Enable this to support Freescale USB OTG transceiver. | |
| config ISP1301_OMAP | |
| tristate "Philips ISP1301 with OMAP OTG" | |
| depends on I2C && ARCH_OMAP_OTG | |
| select USB_PHY | |
| help | |
| If you say yes here you get support for the Philips ISP1301 | |
| USB-On-The-Go transceiver working with the OMAP OTG controller. | |
| The ISP1301 is a full speed USB transceiver which is used in | |
| products including H2, H3, and H4 development boards for Texas | |
| Instruments OMAP processors. | |
| This driver can also be built as a module. If so, the module | |
| will be called isp1301_omap. | |
| config MV_U3D_PHY | |
| bool "Marvell USB 3.0 PHY controller Driver" | |
| depends on CPU_MMP3 | |
| select USB_PHY | |
| help | |
| Enable this to support Marvell USB 3.0 phy controller for Marvell | |
| SoC. | |
| config NOP_USB_XCEIV | |
| tristate "NOP USB Transceiver Driver" | |
| select USB_PHY | |
| help | |
| This driver is to be used by all the usb transceiver which are either | |
| built-in with usb ip or which are autonomous and doesn't require any | |
| phy programming such as ISP1x04 etc. | |
| config OMAP_CONTROL_USB | |
| tristate "OMAP CONTROL USB Driver" | |
| help | |
| Enable this to add support for the USB part present in the control | |
| module. This driver has API to power on the USB2 PHY and to write to | |
| the mailbox. The mailbox is present only in omap4 and the register to | |
| power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an | |
| additional register to power on USB3 PHY. | |
| config OMAP_USB2 | |
| tristate "OMAP USB2 PHY Driver" | |
| depends on ARCH_OMAP2PLUS | |
| select OMAP_CONTROL_USB | |
| select USB_PHY | |
| help | |
| Enable this to support the transceiver that is part of SOC. This | |
| driver takes care of all the PHY functionality apart from comparator. | |
| The USB OTG controller communicates with the comparator using this | |
| driver. | |
| config OMAP_USB3 | |
| tristate "OMAP USB3 PHY Driver" | |
| select OMAP_CONTROL_USB | |
| select USB_PHY | |
| help | |
| Enable this to support the USB3 PHY that is part of SOC. This | |
| driver takes care of all the PHY functionality apart from comparator. | |
| This driver interacts with the "OMAP Control USB Driver" to power | |
| on/off the PHY. | |
| config SAMSUNG_USBPHY | |
| tristate "Samsung USB PHY Driver" | |
| help | |
| Enable this to support Samsung USB phy helper driver for Samsung SoCs. | |
| This driver provides common interface to interact, for Samsung USB 2.0 PHY | |
| driver and later for Samsung USB 3.0 PHY driver. | |
| config SAMSUNG_USB2PHY | |
| tristate "Samsung USB 2.0 PHY controller Driver" | |
| select SAMSUNG_USBPHY | |
| select USB_PHY | |
| help | |
| Enable this to support Samsung USB 2.0 (High Speed) PHY controller | |
| driver for Samsung SoCs. | |
| config SAMSUNG_USB3PHY | |
| tristate "Samsung USB 3.0 PHY controller Driver" | |
| select SAMSUNG_USBPHY | |
| select USB_PHY | |
| help | |
| Enable this to support Samsung USB 3.0 (Super Speed) phy controller | |
| for samsung SoCs. | |
| config TWL4030_USB | |
| tristate "TWL4030 USB Transceiver Driver" | |
| depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS | |
| select USB_PHY | |
| help | |
| Enable this to support the USB OTG transceiver on TWL4030 | |
| family chips (including the TWL5030 and TPS659x0 devices). | |
| This transceiver supports high and full speed devices plus, | |
| in host mode, low speed. | |
| config TWL6030_USB | |
| tristate "TWL6030 USB Transceiver Driver" | |
| depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS | |
| help | |
| Enable this to support the USB OTG transceiver on TWL6030 | |
| family chips. This TWL6030 transceiver has the VBUS and ID GND | |
| and OTG SRP events capabilities. For all other transceiver functionality | |
| UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs | |
| are hooked to this driver through platform_data structure. | |
| The definition of internal PHY APIs are in the mach-omap2 layer. | |
| config USB_GPIO_VBUS | |
| tristate "GPIO based peripheral-only VBUS sensing 'transceiver'" | |
| depends on GPIOLIB | |
| select USB_PHY | |
| help | |
| Provides simple GPIO VBUS sensing for controllers with an | |
| internal transceiver via the usb_phy interface, and | |
| optionally control of a D+ pullup GPIO as well as a VBUS | |
| current limit regulator. | |
| config USB_ISP1301 | |
| tristate "NXP ISP1301 USB transceiver support" | |
| depends on USB || USB_GADGET | |
| depends on I2C | |
| select USB_PHY | |
| help | |
| Say Y here to add support for the NXP ISP1301 USB transceiver driver. | |
| This chip is typically used as USB transceiver for USB host, gadget | |
| and OTG drivers (to be selected separately). | |
| To compile this driver as a module, choose M here: the | |
| module will be called isp1301. | |
| config USB_MSM_OTG | |
| tristate "OTG support for Qualcomm on-chip USB controller" | |
| depends on (USB || USB_GADGET) && ARCH_MSM | |
| select USB_PHY | |
| help | |
| Enable this to support the USB OTG transceiver on MSM chips. It | |
| handles PHY initialization, clock management, and workarounds | |
| required after resetting the hardware and power management. | |
| This driver is required even for peripheral only or host only | |
| mode configurations. | |
| This driver is not supported on boards like trout which | |
| has an external PHY. | |
| config USB_MV_OTG | |
| tristate "Marvell USB OTG support" | |
| depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME | |
| select USB_OTG | |
| select USB_PHY | |
| help | |
| Say Y here if you want to build Marvell USB OTG transciever | |
| driver in kernel (including PXA and MMP series). This driver | |
| implements role switch between EHCI host driver and gadget driver. | |
| To compile this driver as a module, choose M here. | |
| config USB_MXS_PHY | |
| tristate "Freescale MXS USB PHY support" | |
| depends on ARCH_MXC || ARCH_MXS | |
| select STMP_DEVICE | |
| select USB_PHY | |
| help | |
| Enable this to support the Freescale MXS USB PHY. | |
| MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x. | |
| config USB_RCAR_PHY | |
| tristate "Renesas R-Car USB phy support" | |
| depends on USB || USB_GADGET | |
| select USB_PHY | |
| help | |
| Say Y here to add support for the Renesas R-Car USB phy driver. | |
| This chip is typically used as USB phy for USB host, gadget. | |
| This driver supports: R8A7779 | |
| To compile this driver as a module, choose M here: the | |
| module will be called rcar-phy. | |
| config USB_ULPI | |
| bool "Generic ULPI Transceiver Driver" | |
| depends on ARM | |
| help | |
| Enable this to support ULPI connected USB OTG transceivers which | |
| are likely found on embedded boards. | |
| config USB_ULPI_VIEWPORT | |
| bool | |
| depends on USB_ULPI | |
| help | |
| Provides read/write operations to the ULPI phy register set for | |
| controllers with a viewport register (e.g. Chipidea/ARC controllers). | |
| endmenu |