| ##### Example wpa_supplicant configuration file ############################### |
| # |
| # This file describes configuration file format and lists all available option. |
| # Please also take a look at simpler configuration examples in 'examples' |
| # subdirectory. |
| # |
| # Empty lines and lines starting with # are ignored |
| |
| # NOTE! This file may contain password information and should probably be made |
| # readable only by root user on multiuser systems. |
| |
| # Note: All file paths in this configuration file should use full (absolute, |
| # not relative to working directory) path in order to allow working directory |
| # to be changed. This can happen if wpa_supplicant is run in the background. |
| |
| # Whether to allow wpa_supplicant to update (overwrite) configuration |
| # |
| # This option can be used to allow wpa_supplicant to overwrite configuration |
| # file whenever configuration is changed (e.g., new network block is added with |
| # wpa_cli or wpa_gui, or a password is changed). This is required for |
| # wpa_cli/wpa_gui to be able to store the configuration changes permanently. |
| # Please note that overwriting configuration file will remove the comments from |
| # it. |
| #update_config=1 |
| |
| # global configuration (shared by all network blocks) |
| # |
| # Parameters for the control interface. If this is specified, wpa_supplicant |
| # will open a control interface that is available for external programs to |
| # manage wpa_supplicant. The meaning of this string depends on which control |
| # interface mechanism is used. For all cases, the existence of this parameter |
| # in configuration is used to determine whether the control interface is |
| # enabled. |
| # |
| # For UNIX domain sockets (default on Linux and BSD): This is a directory that |
| # will be created for UNIX domain sockets for listening to requests from |
| # external programs (CLI/GUI, etc.) for status information and configuration. |
| # The socket file will be named based on the interface name, so multiple |
| # wpa_supplicant processes can be run at the same time if more than one |
| # interface is used. |
| # /var/run/wpa_supplicant is the recommended directory for sockets and by |
| # default, wpa_cli will use it when trying to connect with wpa_supplicant. |
| # |
| # Access control for the control interface can be configured by setting the |
| # directory to allow only members of a group to use sockets. This way, it is |
| # possible to run wpa_supplicant as root (since it needs to change network |
| # configuration and open raw sockets) and still allow GUI/CLI components to be |
| # run as non-root users. However, since the control interface can be used to |
| # change the network configuration, this access needs to be protected in many |
| # cases. By default, wpa_supplicant is configured to use gid 0 (root). If you |
| # want to allow non-root users to use the control interface, add a new group |
| # and change this value to match with that group. Add users that should have |
| # control interface access to this group. If this variable is commented out or |
| # not included in the configuration file, group will not be changed from the |
| # value it got by default when the directory or socket was created. |
| # |
| # When configuring both the directory and group, use following format: |
| # DIR=/var/run/wpa_supplicant GROUP=wheel |
| # DIR=/var/run/wpa_supplicant GROUP=0 |
| # (group can be either group name or gid) |
| # |
| # For UDP connections (default on Windows): The value will be ignored. This |
| # variable is just used to select that the control interface is to be created. |
| # The value can be set to, e.g., udp (ctrl_interface=udp) |
| # |
| # For Windows Named Pipe: This value can be used to set the security descriptor |
| # for controlling access to the control interface. Security descriptor can be |
| # set using Security Descriptor String Format (see http://msdn.microsoft.com/ |
| # library/default.asp?url=/library/en-us/secauthz/security/ |
| # security_descriptor_string_format.asp). The descriptor string needs to be |
| # prefixed with SDDL=. For example, ctrl_interface=SDDL=D: would set an empty |
| # DACL (which will reject all connections). See README-Windows.txt for more |
| # information about SDDL string format. |
| # |
| ctrl_interface=/var/run/wpa_supplicant |
| |
| # IEEE 802.1X/EAPOL version |
| # wpa_supplicant is implemented based on IEEE Std 802.1X-2004 which defines |
| # EAPOL version 2. However, there are many APs that do not handle the new |
| # version number correctly (they seem to drop the frames completely). In order |
| # to make wpa_supplicant interoperate with these APs, the version number is set |
| # to 1 by default. This configuration value can be used to set it to the new |
| # version (2). |
| eapol_version=1 |
| |
| # AP scanning/selection |
| # By default, wpa_supplicant requests driver to perform AP scanning and then |
| # uses the scan results to select a suitable AP. Another alternative is to |
| # allow the driver to take care of AP scanning and selection and use |
| # wpa_supplicant just to process EAPOL frames based on IEEE 802.11 association |
| # information from the driver. |
| # 1: wpa_supplicant initiates scanning and AP selection; if no APs matching to |
| # the currently enabled networks are found, a new network (IBSS or AP mode |
| # operation) may be initialized (if configured) (default) |
| # 0: driver takes care of scanning, AP selection, and IEEE 802.11 association |
| # parameters (e.g., WPA IE generation); this mode can also be used with |
| # non-WPA drivers when using IEEE 802.1X mode; do not try to associate with |
| # APs (i.e., external program needs to control association). This mode must |
| # also be used when using wired Ethernet drivers. |
| # 2: like 0, but associate with APs using security policy and SSID (but not |
| # BSSID); this can be used, e.g., with ndiswrapper and NDIS drivers to |
| # enable operation with hidden SSIDs and optimized roaming; in this mode, |
| # the network blocks in the configuration file are tried one by one until |
| # the driver reports successful association; each network block should have |
| # explicit security policy (i.e., only one option in the lists) for |
| # key_mgmt, pairwise, group, proto variables |
| # When using IBSS or AP mode, ap_scan=2 mode can force the new network to be |
| # created immediately regardless of scan results. ap_scan=1 mode will first try |
| # to scan for existing networks and only if no matches with the enabled |
| # networks are found, a new IBSS or AP mode network is created. |
| ap_scan=1 |
| |
| # EAP fast re-authentication |
| # By default, fast re-authentication is enabled for all EAP methods that |
| # support it. This variable can be used to disable fast re-authentication. |
| # Normally, there is no need to disable this. |
| fast_reauth=1 |
| |
| # OpenSSL Engine support |
| # These options can be used to load OpenSSL engines. |
| # The two engines that are supported currently are shown below: |
| # They are both from the opensc project (http://www.opensc.org/) |
| # By default no engines are loaded. |
| # make the opensc engine available |
| #opensc_engine_path=/usr/lib/opensc/engine_opensc.so |
| # make the pkcs11 engine available |
| #pkcs11_engine_path=/usr/lib/opensc/engine_pkcs11.so |
| # configure the path to the pkcs11 module required by the pkcs11 engine |
| #pkcs11_module_path=/usr/lib/pkcs11/opensc-pkcs11.so |
| |
| # Dynamic EAP methods |
| # If EAP methods were built dynamically as shared object files, they need to be |
| # loaded here before being used in the network blocks. By default, EAP methods |
| # are included statically in the build, so these lines are not needed |
| #load_dynamic_eap=/usr/lib/wpa_supplicant/eap_tls.so |
| #load_dynamic_eap=/usr/lib/wpa_supplicant/eap_md5.so |
| |
| # Driver interface parameters |
| # This field can be used to configure arbitrary driver interace parameters. The |
| # format is specific to the selected driver interface. This field is not used |
| # in most cases. |
| #driver_param="field=value" |
| |
| # Country code |
| # The ISO/IEC alpha2 country code for the country in which this device is |
| # currently operating. |
| #country=US |
| |
| # Maximum lifetime for PMKSA in seconds; default 43200 |
| #dot11RSNAConfigPMKLifetime=43200 |
| # Threshold for reauthentication (percentage of PMK lifetime); default 70 |
| #dot11RSNAConfigPMKReauthThreshold=70 |
| # Timeout for security association negotiation in seconds; default 60 |
| #dot11RSNAConfigSATimeout=60 |
| |
| # Wi-Fi Protected Setup (WPS) parameters |
| |
| # Universally Unique IDentifier (UUID; see RFC 4122) of the device |
| # If not configured, UUID will be generated based on the local MAC address. |
| #uuid=12345678-9abc-def0-1234-56789abcdef0 |
| |
| # Device Name |
| # User-friendly description of device; up to 32 octets encoded in UTF-8 |
| #device_name=Wireless Client |
| |
| # Manufacturer |
| # The manufacturer of the device (up to 64 ASCII characters) |
| #manufacturer=Company |
| |
| # Model Name |
| # Model of the device (up to 32 ASCII characters) |
| #model_name=cmodel |
| |
| # Model Number |
| # Additional device description (up to 32 ASCII characters) |
| #model_number=123 |
| |
| # Serial Number |
| # Serial number of the device (up to 32 characters) |
| #serial_number=12345 |
| |
| # Primary Device Type |
| # Used format: <categ>-<OUI>-<subcateg> |
| # categ = Category as an integer value |
| # OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for |
| # default WPS OUI |
| # subcateg = OUI-specific Sub Category as an integer value |
| # Examples: |
| # 1-0050F204-1 (Computer / PC) |
| # 1-0050F204-2 (Computer / Server) |
| # 5-0050F204-1 (Storage / NAS) |
| # 6-0050F204-1 (Network Infrastructure / AP) |
| #device_type=1-0050F204-1 |
| |
| # OS Version |
| # 4-octet operating system version number (hex string) |
| #os_version=01020300 |
| |
| # Config Methods |
| # List of the supported configuration methods |
| # Available methods: usba ethernet label display ext_nfc_token int_nfc_token |
| # nfc_interface push_button keypad virtual_display physical_display |
| # virtual_push_button physical_push_button |
| # For WSC 1.0: |
| #config_methods=label display push_button keypad |
| # For WSC 2.0: |
| #config_methods=label virtual_display virtual_push_button keypad |
| |
| # Credential processing |
| # 0 = process received credentials internally (default) |
| # 1 = do not process received credentials; just pass them over ctrl_iface to |
| # external program(s) |
| # 2 = process received credentials internally and pass them over ctrl_iface |
| # to external program(s) |
| #wps_cred_processing=0 |
| |
| # Vendor attribute in WPS M1, e.g., Windows 7 Vertical Pairing |
| # The vendor attribute contents to be added in M1 (hex string) |
| #wps_vendor_ext_m1=000137100100020001 |
| |
| # NFC password token for WPS |
| # These parameters can be used to configure a fixed NFC password token for the |
| # station. This can be generated, e.g., with nfc_pw_token. When these |
| # parameters are used, the station is assumed to be deployed with a NFC tag |
| # that includes the matching NFC password token (e.g., written based on the |
| # NDEF record from nfc_pw_token). |
| # |
| #wps_nfc_dev_pw_id: Device Password ID (16..65535) |
| #wps_nfc_dh_pubkey: Hexdump of DH Public Key |
| #wps_nfc_dh_privkey: Hexdump of DH Private Key |
| #wps_nfc_dev_pw: Hexdump of Device Password |
| |
| # Maximum number of BSS entries to keep in memory |
| # Default: 200 |
| # This can be used to limit memory use on the BSS entries (cached scan |
| # results). A larger value may be needed in environments that have huge number |
| # of APs when using ap_scan=1 mode. |
| #bss_max_count=200 |
| |
| # Automatic scan |
| # This is an optional set of parameters for automatic scanning |
| # within an interface in following format: |
| #autoscan=<autoscan module name>:<module parameters> |
| # autoscan is like bgscan but on disconnected or inactive state. |
| # For instance, on exponential module parameters would be <base>:<limit> |
| #autoscan=exponential:3:300 |
| # Which means a delay between scans on a base exponential of 3, |
| # up to the limit of 300 seconds (3, 9, 27 ... 300) |
| # For periodic module, parameters would be <fixed interval> |
| #autoscan=periodic:30 |
| # So a delay of 30 seconds will be applied between each scan |
| |
| # filter_ssids - SSID-based scan result filtering |
| # 0 = do not filter scan results (default) |
| # 1 = only include configured SSIDs in scan results/BSS table |
| #filter_ssids=0 |
| |
| # Password (and passphrase, etc.) backend for external storage |
| # format: <backend name>[:<optional backend parameters>] |
| #ext_password_backend=test:pw1=password|pw2=testing |
| |
| # Timeout in seconds to detect STA inactivity (default: 300 seconds) |
| # |
| # This timeout value is used in P2P GO mode to clean up |
| # inactive stations. |
| #p2p_go_max_inactivity=300 |
| |
| # Opportunistic Key Caching (also known as Proactive Key Caching) default |
| # This parameter can be used to set the default behavior for the |
| # proactive_key_caching parameter. By default, OKC is disabled unless enabled |
| # with the global okc=1 parameter or with the per-network |
| # proactive_key_caching=1 parameter. With okc=1, OKC is enabled by default, but |
| # can be disabled with per-network proactive_key_caching=0 parameter. |
| #okc=0 |
| |
| # Protected Management Frames default |
| # This parameter can be used to set the default behavior for the ieee80211w |
| # parameter. By default, PMF is disabled unless enabled with the global pmf=1/2 |
| # parameter or with the per-network ieee80211w=1/2 parameter. With pmf=1/2, PMF |
| # is enabled/required by default, but can be disabled with the per-network |
| # ieee80211w parameter. |
| #pmf=0 |
| |
| # Interworking (IEEE 802.11u) |
| |
| # Enable Interworking |
| # interworking=1 |
| |
| # Homogenous ESS identifier |
| # If this is set, scans will be used to request response only from BSSes |
| # belonging to the specified Homogeneous ESS. This is used only if interworking |
| # is enabled. |
| # hessid=00:11:22:33:44:55 |
| |
| # Automatic network selection behavior |
| # 0 = do not automatically go through Interworking network selection |
| # (i.e., require explicit interworking_select command for this; default) |
| # 1 = perform Interworking network selection if one or more |
| # credentials have been configured and scan did not find a |
| # matching network block |
| #auto_interworking=0 |
| |
| # credential block |
| # |
| # Each credential used for automatic network selection is configured as a set |
| # of parameters that are compared to the information advertised by the APs when |
| # interworking_select and interworking_connect commands are used. |
| # |
| # credential fields: |
| # |
| # priority: Priority group |
| # By default, all networks and credentials get the same priority group |
| # (0). This field can be used to give higher priority for credentials |
| # (and similarly in struct wpa_ssid for network blocks) to change the |
| # Interworking automatic networking selection behavior. The matching |
| # network (based on either an enabled network block or a credential) |
| # with the highest priority value will be selected. |
| # |
| # pcsc: Use PC/SC and SIM/USIM card |
| # |
| # realm: Home Realm for Interworking |
| # |
| # username: Username for Interworking network selection |
| # |
| # password: Password for Interworking network selection |
| # |
| # ca_cert: CA certificate for Interworking network selection |
| # |
| # client_cert: File path to client certificate file (PEM/DER) |
| # This field is used with Interworking networking selection for a case |
| # where client certificate/private key is used for authentication |
| # (EAP-TLS). Full path to the file should be used since working |
| # directory may change when wpa_supplicant is run in the background. |
| # |
| # Alternatively, a named configuration blob can be used by setting |
| # this to blob://blob_name. |
| # |
| # private_key: File path to client private key file (PEM/DER/PFX) |
| # When PKCS#12/PFX file (.p12/.pfx) is used, client_cert should be |
| # commented out. Both the private key and certificate will be read |
| # from the PKCS#12 file in this case. Full path to the file should be |
| # used since working directory may change when wpa_supplicant is run |
| # in the background. |
| # |
| # Windows certificate store can be used by leaving client_cert out and |
| # configuring private_key in one of the following formats: |
| # |
| # cert://substring_to_match |
| # |
| # hash://certificate_thumbprint_in_hex |
| # |
| # For example: private_key="hash://63093aa9c47f56ae88334c7b65a4" |
| # |
| # Note that when running wpa_supplicant as an application, the user |
| # certificate store (My user account) is used, whereas computer store |
| # (Computer account) is used when running wpasvc as a service. |
| # |
| # Alternatively, a named configuration blob can be used by setting |
| # this to blob://blob_name. |
| # |
| # private_key_passwd: Password for private key file |
| # |
| # imsi: IMSI in <MCC> | <MNC> | '-' | <MSIN> format |
| # |
| # milenage: Milenage parameters for SIM/USIM simulator in <Ki>:<OPc>:<SQN> |
| # format |
| # |
| # domain: Home service provider FQDN |
| # This is used to compare against the Domain Name List to figure out |
| # whether the AP is operated by the Home SP. |
| # |
| # roaming_consortium: Roaming Consortium OI |
| # If roaming_consortium_len is non-zero, this field contains the |
| # Roaming Consortium OI that can be used to determine which access |
| # points support authentication with this credential. This is an |
| # alternative to the use of the realm parameter. When using Roaming |
| # Consortium to match the network, the EAP parameters need to be |
| # pre-configured with the credential since the NAI Realm information |
| # may not be available or fetched. |
| # |
| # eap: Pre-configured EAP method |
| # This optional field can be used to specify which EAP method will be |
| # used with this credential. If not set, the EAP method is selected |
| # automatically based on ANQP information (e.g., NAI Realm). |
| # |
| # phase1: Pre-configure Phase 1 (outer authentication) parameters |
| # This optional field is used with like the 'eap' parameter. |
| # |
| # phase2: Pre-configure Phase 2 (inner authentication) parameters |
| # This optional field is used with like the 'eap' parameter. |
| # |
| # excluded_ssid: Excluded SSID |
| # This optional field can be used to excluded specific SSID(s) from |
| # matching with the network. Multiple entries can be used to specify more |
| # than one SSID. |
| # |
| # for example: |
| # |
| #cred={ |
| # realm="example.com" |
| # username="user@example.com" |
| # password="password" |
| # ca_cert="/etc/wpa_supplicant/ca.pem" |
| # domain="example.com" |
| #} |
| # |
| #cred={ |
| # imsi="310026-000000000" |
| # milenage="90dca4eda45b53cf0f12d7c9c3bc6a89:cb9cccc4b9258e6dca4760379fb82" |
| #} |
| # |
| #cred={ |
| # realm="example.com" |
| # username="user" |
| # password="password" |
| # ca_cert="/etc/wpa_supplicant/ca.pem" |
| # domain="example.com" |
| # roaming_consortium=223344 |
| # eap=TTLS |
| # phase2="auth=MSCHAPV2" |
| #} |
| |
| # Hotspot 2.0 |
| # hs20=1 |
| |
| # network block |
| # |
| # Each network (usually AP's sharing the same SSID) is configured as a separate |
| # block in this configuration file. The network blocks are in preference order |
| # (the first match is used). |
| # |
| # network block fields: |
| # |
| # disabled: |
| # 0 = this network can be used (default) |
| # 1 = this network block is disabled (can be enabled through ctrl_iface, |
| # e.g., with wpa_cli or wpa_gui) |
| # |
| # id_str: Network identifier string for external scripts. This value is passed |
| # to external action script through wpa_cli as WPA_ID_STR environment |
| # variable to make it easier to do network specific configuration. |
| # |
| # ssid: SSID (mandatory); network name in one of the optional formats: |
| # - an ASCII string with double quotation |
| # - a hex string (two characters per octet of SSID) |
| # - a printf-escaped ASCII string P"<escaped string>" |
| # |
| # scan_ssid: |
| # 0 = do not scan this SSID with specific Probe Request frames (default) |
| # 1 = scan with SSID-specific Probe Request frames (this can be used to |
| # find APs that do not accept broadcast SSID or use multiple SSIDs; |
| # this will add latency to scanning, so enable this only when needed) |
| # |
| # bssid: BSSID (optional); if set, this network block is used only when |
| # associating with the AP using the configured BSSID |
| # |
| # priority: priority group (integer) |
| # By default, all networks will get same priority group (0). If some of the |
| # networks are more desirable, this field can be used to change the order in |
| # which wpa_supplicant goes through the networks when selecting a BSS. The |
| # priority groups will be iterated in decreasing priority (i.e., the larger the |
| # priority value, the sooner the network is matched against the scan results). |
| # Within each priority group, networks will be selected based on security |
| # policy, signal strength, etc. |
| # Please note that AP scanning with scan_ssid=1 and ap_scan=2 mode are not |
| # using this priority to select the order for scanning. Instead, they try the |
| # networks in the order that used in the configuration file. |
| # |
| # mode: IEEE 802.11 operation mode |
| # 0 = infrastructure (Managed) mode, i.e., associate with an AP (default) |
| # 1 = IBSS (ad-hoc, peer-to-peer) |
| # 2 = AP (access point) |
| # Note: IBSS can only be used with key_mgmt NONE (plaintext and static WEP) |
| # and key_mgmt=WPA-NONE (fixed group key TKIP/CCMP). WPA-None requires |
| # following network block options: |
| # proto=WPA, key_mgmt=WPA-NONE, pairwise=NONE, group=TKIP (or CCMP, but not |
| # both), and psk must also be set. |
| # |
| # frequency: Channel frequency in megahertz (MHz) for IBSS, e.g., |
| # 2412 = IEEE 802.11b/g channel 1. This value is used to configure the initial |
| # channel for IBSS (adhoc) networks. It is ignored in the infrastructure mode. |
| # In addition, this value is only used by the station that creates the IBSS. If |
| # an IBSS network with the configured SSID is already present, the frequency of |
| # the network will be used instead of this configured value. |
| # |
| # scan_freq: List of frequencies to scan |
| # Space-separated list of frequencies in MHz to scan when searching for this |
| # BSS. If the subset of channels used by the network is known, this option can |
| # be used to optimize scanning to not occur on channels that the network does |
| # not use. Example: scan_freq=2412 2437 2462 |
| # |
| # freq_list: Array of allowed frequencies |
| # Space-separated list of frequencies in MHz to allow for selecting the BSS. If |
| # set, scan results that do not match any of the specified frequencies are not |
| # considered when selecting a BSS. |
| # |
| # bgscan: Background scanning |
| # wpa_supplicant behavior for background scanning can be specified by |
| # configuring a bgscan module. These modules are responsible for requesting |
| # background scans for the purpose of roaming within an ESS (i.e., within a |
| # single network block with all the APs using the same SSID). The bgscan |
| # parameter uses following format: "<bgscan module name>:<module parameters>" |
| # Following bgscan modules are available: |
| # simple - Periodic background scans based on signal strength |
| # bgscan="simple:<short bgscan interval in seconds>:<signal strength threshold>: |
| # <long interval>" |
| # bgscan="simple:30:-45:300" |
| # learn - Learn channels used by the network and try to avoid bgscans on other |
| # channels (experimental) |
| # bgscan="learn:<short bgscan interval in seconds>:<signal strength threshold>: |
| # <long interval>[:<database file name>]" |
| # bgscan="learn:30:-45:300:/etc/wpa_supplicant/network1.bgscan" |
| # |
| # proto: list of accepted protocols |
| # WPA = WPA/IEEE 802.11i/D3.0 |
| # RSN = WPA2/IEEE 802.11i (also WPA2 can be used as an alias for RSN) |
| # If not set, this defaults to: WPA RSN |
| # |
| # key_mgmt: list of accepted authenticated key management protocols |
| # WPA-PSK = WPA pre-shared key (this requires 'psk' field) |
| # WPA-EAP = WPA using EAP authentication |
| # IEEE8021X = IEEE 802.1X using EAP authentication and (optionally) dynamically |
| # generated WEP keys |
| # NONE = WPA is not used; plaintext or static WEP could be used |
| # WPA-PSK-SHA256 = Like WPA-PSK but using stronger SHA256-based algorithms |
| # WPA-EAP-SHA256 = Like WPA-EAP but using stronger SHA256-based algorithms |
| # If not set, this defaults to: WPA-PSK WPA-EAP |
| # |
| # ieee80211w: whether management frame protection is enabled |
| # 0 = disabled (default unless changed with the global pmf parameter) |
| # 1 = optional |
| # 2 = required |
| # The most common configuration options for this based on the PMF (protected |
| # management frames) certification program are: |
| # PMF enabled: ieee80211w=1 and key_mgmt=WPA-EAP WPA-EAP-SHA256 |
| # PMF required: ieee80211w=2 and key_mgmt=WPA-EAP-SHA256 |
| # (and similarly for WPA-PSK and WPA-WPSK-SHA256 if WPA2-Personal is used) |
| # |
| # auth_alg: list of allowed IEEE 802.11 authentication algorithms |
| # OPEN = Open System authentication (required for WPA/WPA2) |
| # SHARED = Shared Key authentication (requires static WEP keys) |
| # LEAP = LEAP/Network EAP (only used with LEAP) |
| # If not set, automatic selection is used (Open System with LEAP enabled if |
| # LEAP is allowed as one of the EAP methods). |
| # |
| # pairwise: list of accepted pairwise (unicast) ciphers for WPA |
| # CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0] |
| # TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0] |
| # NONE = Use only Group Keys (deprecated, should not be included if APs support |
| # pairwise keys) |
| # If not set, this defaults to: CCMP TKIP |
| # |
| # group: list of accepted group (broadcast/multicast) ciphers for WPA |
| # CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0] |
| # TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0] |
| # WEP104 = WEP (Wired Equivalent Privacy) with 104-bit key |
| # WEP40 = WEP (Wired Equivalent Privacy) with 40-bit key [IEEE 802.11] |
| # If not set, this defaults to: CCMP TKIP WEP104 WEP40 |
| # |
| # psk: WPA preshared key; 256-bit pre-shared key |
| # The key used in WPA-PSK mode can be entered either as 64 hex-digits, i.e., |
| # 32 bytes or as an ASCII passphrase (in which case, the real PSK will be |
| # generated using the passphrase and SSID). ASCII passphrase must be between |
| # 8 and 63 characters (inclusive). ext:<name of external PSK field> format can |
| # be used to indicate that the PSK/passphrase is stored in external storage. |
| # This field is not needed, if WPA-EAP is used. |
| # Note: Separate tool, wpa_passphrase, can be used to generate 256-bit keys |
| # from ASCII passphrase. This process uses lot of CPU and wpa_supplicant |
| # startup and reconfiguration time can be optimized by generating the PSK only |
| # only when the passphrase or SSID has actually changed. |
| # |
| # eapol_flags: IEEE 802.1X/EAPOL options (bit field) |
| # Dynamic WEP key required for non-WPA mode |
| # bit0 (1): require dynamically generated unicast WEP key |
| # bit1 (2): require dynamically generated broadcast WEP key |
| # (3 = require both keys; default) |
| # Note: When using wired authentication, eapol_flags must be set to 0 for the |
| # authentication to be completed successfully. |
| # |
| # mixed_cell: This option can be used to configure whether so called mixed |
| # cells, i.e., networks that use both plaintext and encryption in the same |
| # SSID, are allowed when selecting a BSS from scan results. |
| # 0 = disabled (default) |
| # 1 = enabled |
| # |
| # proactive_key_caching: |
| # Enable/disable opportunistic PMKSA caching for WPA2. |
| # 0 = disabled (default unless changed with the global okc parameter) |
| # 1 = enabled |
| # |
| # wep_key0..3: Static WEP key (ASCII in double quotation, e.g. "abcde" or |
| # hex without quotation, e.g., 0102030405) |
| # wep_tx_keyidx: Default WEP key index (TX) (0..3) |
| # |
| # peerkey: Whether PeerKey negotiation for direct links (IEEE 802.11e DLS) is |
| # allowed. This is only used with RSN/WPA2. |
| # 0 = disabled (default) |
| # 1 = enabled |
| #peerkey=1 |
| # |
| # wpa_ptk_rekey: Maximum lifetime for PTK in seconds. This can be used to |
| # enforce rekeying of PTK to mitigate some attacks against TKIP deficiencies. |
| # |
| # Following fields are only used with internal EAP implementation. |
| # eap: space-separated list of accepted EAP methods |
| # MD5 = EAP-MD5 (unsecure and does not generate keying material -> |
| # cannot be used with WPA; to be used as a Phase 2 method |
| # with EAP-PEAP or EAP-TTLS) |
| # MSCHAPV2 = EAP-MSCHAPv2 (cannot be used separately with WPA; to be used |
| # as a Phase 2 method with EAP-PEAP or EAP-TTLS) |
| # OTP = EAP-OTP (cannot be used separately with WPA; to be used |
| # as a Phase 2 method with EAP-PEAP or EAP-TTLS) |
| # GTC = EAP-GTC (cannot be used separately with WPA; to be used |
| # as a Phase 2 method with EAP-PEAP or EAP-TTLS) |
| # TLS = EAP-TLS (client and server certificate) |
| # PEAP = EAP-PEAP (with tunnelled EAP authentication) |
| # TTLS = EAP-TTLS (with tunnelled EAP or PAP/CHAP/MSCHAP/MSCHAPV2 |
| # authentication) |
| # If not set, all compiled in methods are allowed. |
| # |
| # identity: Identity string for EAP |
| # This field is also used to configure user NAI for |
| # EAP-PSK/PAX/SAKE/GPSK. |
| # anonymous_identity: Anonymous identity string for EAP (to be used as the |
| # unencrypted identity with EAP types that support different tunnelled |
| # identity, e.g., EAP-TTLS). This field can also be used with |
| # EAP-SIM/AKA/AKA' to store the pseudonym identity. |
| # password: Password string for EAP. This field can include either the |
| # plaintext password (using ASCII or hex string) or a NtPasswordHash |
| # (16-byte MD4 hash of password) in hash:<32 hex digits> format. |
| # NtPasswordHash can only be used when the password is for MSCHAPv2 or |
| # MSCHAP (EAP-MSCHAPv2, EAP-TTLS/MSCHAPv2, EAP-TTLS/MSCHAP, LEAP). |
| # EAP-PSK (128-bit PSK), EAP-PAX (128-bit PSK), and EAP-SAKE (256-bit |
| # PSK) is also configured using this field. For EAP-GPSK, this is a |
| # variable length PSK. ext:<name of external password field> format can |
| # be used to indicate that the password is stored in external storage. |
| # ca_cert: File path to CA certificate file (PEM/DER). This file can have one |
| # or more trusted CA certificates. If ca_cert and ca_path are not |
| # included, server certificate will not be verified. This is insecure and |
| # a trusted CA certificate should always be configured when using |
| # EAP-TLS/TTLS/PEAP. Full path should be used since working directory may |
| # change when wpa_supplicant is run in the background. |
| # |
| # Alternatively, this can be used to only perform matching of the server |
| # certificate (SHA-256 hash of the DER encoded X.509 certificate). In |
| # this case, the possible CA certificates in the server certificate chain |
| # are ignored and only the server certificate is verified. This is |
| # configured with the following format: |
| # hash:://server/sha256/cert_hash_in_hex |
| # For example: "hash://server/sha256/ |
| # 5a1bc1296205e6fdbe3979728efe3920798885c1c4590b5f90f43222d239ca6a" |
| # |
| # On Windows, trusted CA certificates can be loaded from the system |
| # certificate store by setting this to cert_store://<name>, e.g., |
| # ca_cert="cert_store://CA" or ca_cert="cert_store://ROOT". |
| # Note that when running wpa_supplicant as an application, the user |
| # certificate store (My user account) is used, whereas computer store |
| # (Computer account) is used when running wpasvc as a service. |
| # ca_path: Directory path for CA certificate files (PEM). This path may |
| # contain multiple CA certificates in OpenSSL format. Common use for this |
| # is to point to system trusted CA list which is often installed into |
| # directory like /etc/ssl/certs. If configured, these certificates are |
| # added to the list of trusted CAs. ca_cert may also be included in that |
| # case, but it is not required. |
| # client_cert: File path to client certificate file (PEM/DER) |
| # Full path should be used since working directory may change when |
| # wpa_supplicant is run in the background. |
| # Alternatively, a named configuration blob can be used by setting this |
| # to blob://<blob name>. |
| # private_key: File path to client private key file (PEM/DER/PFX) |
| # When PKCS#12/PFX file (.p12/.pfx) is used, client_cert should be |
| # commented out. Both the private key and certificate will be read from |
| # the PKCS#12 file in this case. Full path should be used since working |
| # directory may change when wpa_supplicant is run in the background. |
| # Windows certificate store can be used by leaving client_cert out and |
| # configuring private_key in one of the following formats: |
| # cert://substring_to_match |
| # hash://certificate_thumbprint_in_hex |
| # for example: private_key="hash://63093aa9c47f56ae88334c7b65a4" |
| # Note that when running wpa_supplicant as an application, the user |
| # certificate store (My user account) is used, whereas computer store |
| # (Computer account) is used when running wpasvc as a service. |
| # Alternatively, a named configuration blob can be used by setting this |
| # to blob://<blob name>. |
| # private_key_passwd: Password for private key file (if left out, this will be |
| # asked through control interface) |
| # dh_file: File path to DH/DSA parameters file (in PEM format) |
| # This is an optional configuration file for setting parameters for an |
| # ephemeral DH key exchange. In most cases, the default RSA |
| # authentication does not use this configuration. However, it is possible |
| # setup RSA to use ephemeral DH key exchange. In addition, ciphers with |
| # DSA keys always use ephemeral DH keys. This can be used to achieve |
| # forward secrecy. If the file is in DSA parameters format, it will be |
| # automatically converted into DH params. |
| # subject_match: Substring to be matched against the subject of the |
| # authentication server certificate. If this string is set, the server |
| # sertificate is only accepted if it contains this string in the subject. |
| # The subject string is in following format: |
| # /C=US/ST=CA/L=San Francisco/CN=Test AS/emailAddress=as@example.com |
| # altsubject_match: Semicolon separated string of entries to be matched against |
| # the alternative subject name of the authentication server certificate. |
| # If this string is set, the server sertificate is only accepted if it |
| # contains one of the entries in an alternative subject name extension. |
| # altSubjectName string is in following format: TYPE:VALUE |
| # Example: EMAIL:server@example.com |
| # Example: DNS:server.example.com;DNS:server2.example.com |
| # Following types are supported: EMAIL, DNS, URI |
| # phase1: Phase1 (outer authentication, i.e., TLS tunnel) parameters |
| # (string with field-value pairs, e.g., "peapver=0" or |
| # "peapver=1 peaplabel=1") |
| # 'peapver' can be used to force which PEAP version (0 or 1) is used. |
| # 'peaplabel=1' can be used to force new label, "client PEAP encryption", |
| # to be used during key derivation when PEAPv1 or newer. Most existing |
| # PEAPv1 implementation seem to be using the old label, "client EAP |
| # encryption", and wpa_supplicant is now using that as the default value. |
| # Some servers, e.g., Radiator, may require peaplabel=1 configuration to |
| # interoperate with PEAPv1; see eap_testing.txt for more details. |
| # 'peap_outer_success=0' can be used to terminate PEAP authentication on |
| # tunneled EAP-Success. This is required with some RADIUS servers that |
| # implement draft-josefsson-pppext-eap-tls-eap-05.txt (e.g., |
| # Lucent NavisRadius v4.4.0 with PEAP in "IETF Draft 5" mode) |
| # include_tls_length=1 can be used to force wpa_supplicant to include |
| # TLS Message Length field in all TLS messages even if they are not |
| # fragmented. |
| # sim_min_num_chal=3 can be used to configure EAP-SIM to require three |
| # challenges (by default, it accepts 2 or 3) |
| # result_ind=1 can be used to enable EAP-SIM and EAP-AKA to use |
| # protected result indication. |
| # 'crypto_binding' option can be used to control PEAPv0 cryptobinding |
| # behavior: |
| # * 0 = do not use cryptobinding (default) |
| # * 1 = use cryptobinding if server supports it |
| # * 2 = require cryptobinding |
| # EAP-WSC (WPS) uses following options: pin=<Device Password> or |
| # pbc=1. |
| # phase2: Phase2 (inner authentication with TLS tunnel) parameters |
| # (string with field-value pairs, e.g., "auth=MSCHAPV2" for EAP-PEAP or |
| # "autheap=MSCHAPV2 autheap=MD5" for EAP-TTLS) |
| # |
| # TLS-based methods can use the following parameters to control TLS behavior |
| # (these are normally in the phase1 parameter, but can be used also in the |
| # phase2 parameter when EAP-TLS is used within the inner tunnel): |
| # tls_allow_md5=1 - allow MD5-based certificate signatures (depending on the |
| # TLS library, these may be disabled by default to enforce stronger |
| # security) |
| # tls_disable_time_checks=1 - ignore certificate validity time (this requests |
| # the TLS library to accept certificates even if they are not currently |
| # valid, i.e., have expired or have not yet become valid; this should be |
| # used only for testing purposes) |
| # tls_disable_session_ticket=1 - disable TLS Session Ticket extension |
| # tls_disable_session_ticket=0 - allow TLS Session Ticket extension to be used |
| # Note: If not set, this is automatically set to 1 for EAP-TLS/PEAP/TTLS |
| # as a workaround for broken authentication server implementations unless |
| # EAP workarounds are disabled with eap_workarounds=0. |
| # For EAP-FAST, this must be set to 0 (or left unconfigured for the |
| # default value to be used automatically). |
| # |
| # Following certificate/private key fields are used in inner Phase2 |
| # authentication when using EAP-TTLS or EAP-PEAP. |
| # ca_cert2: File path to CA certificate file. This file can have one or more |
| # trusted CA certificates. If ca_cert2 and ca_path2 are not included, |
| # server certificate will not be verified. This is insecure and a trusted |
| # CA certificate should always be configured. |
| # ca_path2: Directory path for CA certificate files (PEM) |
| # client_cert2: File path to client certificate file |
| # private_key2: File path to client private key file |
| # private_key2_passwd: Password for private key file |
| # dh_file2: File path to DH/DSA parameters file (in PEM format) |
| # subject_match2: Substring to be matched against the subject of the |
| # authentication server certificate. |
| # altsubject_match2: Substring to be matched against the alternative subject |
| # name of the authentication server certificate. |
| # |
| # fragment_size: Maximum EAP fragment size in bytes (default 1398). |
| # This value limits the fragment size for EAP methods that support |
| # fragmentation (e.g., EAP-TLS and EAP-PEAP). This value should be set |
| # small enough to make the EAP messages fit in MTU of the network |
| # interface used for EAPOL. The default value is suitable for most |
| # cases. |
| # |
| # EAP-FAST variables: |
| # pac_file: File path for the PAC entries. wpa_supplicant will need to be able |
| # to create this file and write updates to it when PAC is being |
| # provisioned or refreshed. Full path to the file should be used since |
| # working directory may change when wpa_supplicant is run in the |
| # background. Alternatively, a named configuration blob can be used by |
| # setting this to blob://<blob name> |
| # phase1: fast_provisioning option can be used to enable in-line provisioning |
| # of EAP-FAST credentials (PAC): |
| # 0 = disabled, |
| # 1 = allow unauthenticated provisioning, |
| # 2 = allow authenticated provisioning, |
| # 3 = allow both unauthenticated and authenticated provisioning |
| # fast_max_pac_list_len=<num> option can be used to set the maximum |
| # number of PAC entries to store in a PAC list (default: 10) |
| # fast_pac_format=binary option can be used to select binary format for |
| # storing PAC entries in order to save some space (the default |
| # text format uses about 2.5 times the size of minimal binary |
| # format) |
| # |
| # wpa_supplicant supports number of "EAP workarounds" to work around |
| # interoperability issues with incorrectly behaving authentication servers. |
| # These are enabled by default because some of the issues are present in large |
| # number of authentication servers. Strict EAP conformance mode can be |
| # configured by disabling workarounds with eap_workaround=0. |
| |
| # Station inactivity limit |
| # |
| # If a station does not send anything in ap_max_inactivity seconds, an |
| # empty data frame is sent to it in order to verify whether it is |
| # still in range. If this frame is not ACKed, the station will be |
| # disassociated and then deauthenticated. This feature is used to |
| # clear station table of old entries when the STAs move out of the |
| # range. |
| # |
| # The station can associate again with the AP if it is still in range; |
| # this inactivity poll is just used as a nicer way of verifying |
| # inactivity; i.e., client will not report broken connection because |
| # disassociation frame is not sent immediately without first polling |
| # the STA with a data frame. |
| # default: 300 (i.e., 5 minutes) |
| #ap_max_inactivity=300 |
| |
| # DTIM period in Beacon intervals for AP mode (default: 2) |
| #dtim_period=2 |
| |
| # disable_ht: Whether HT (802.11n) should be disabled. |
| # 0 = HT enabled (if AP supports it) |
| # 1 = HT disabled |
| # |
| # disable_ht40: Whether HT-40 (802.11n) should be disabled. |
| # 0 = HT-40 enabled (if AP supports it) |
| # 1 = HT-40 disabled |
| # |
| # disable_sgi: Whether SGI (short guard interval) should be disabled. |
| # 0 = SGI enabled (if AP supports it) |
| # 1 = SGI disabled |
| # |
| # ht_mcs: Configure allowed MCS rates. |
| # Parsed as an array of bytes, in base-16 (ascii-hex) |
| # ht_mcs="" // Use all available (default) |
| # ht_mcs="0xff 00 00 00 00 00 00 00 00 00 " // Use MCS 0-7 only |
| # ht_mcs="0xff ff 00 00 00 00 00 00 00 00 " // Use MCS 0-15 only |
| # |
| # disable_max_amsdu: Whether MAX_AMSDU should be disabled. |
| # -1 = Do not make any changes. |
| # 0 = Enable MAX-AMSDU if hardware supports it. |
| # 1 = Disable AMSDU |
| # |
| # ampdu_density: Allow overriding AMPDU density configuration. |
| # Treated as hint by the kernel. |
| # -1 = Do not make any changes. |
| # 0-3 = Set AMPDU density (aka factor) to specified value. |
| |
| # Example blocks: |
| |
| # Simple case: WPA-PSK, PSK as an ASCII passphrase, allow all valid ciphers |
| network={ |
| ssid="simple" |
| psk="very secret passphrase" |
| priority=5 |
| } |
| |
| # Same as previous, but request SSID-specific scanning (for APs that reject |
| # broadcast SSID) |
| network={ |
| ssid="second ssid" |
| scan_ssid=1 |
| psk="very secret passphrase" |
| priority=2 |
| } |
| |
| # Only WPA-PSK is used. Any valid cipher combination is accepted. |
| network={ |
| ssid="example" |
| proto=WPA |
| key_mgmt=WPA-PSK |
| pairwise=CCMP TKIP |
| group=CCMP TKIP WEP104 WEP40 |
| psk=06b4be19da289f475aa46a33cb793029d4ab3db7a23ee92382eb0106c72ac7bb |
| priority=2 |
| } |
| |
| # WPA-Personal(PSK) with TKIP and enforcement for frequent PTK rekeying |
| network={ |
| ssid="example" |
| proto=WPA |
| key_mgmt=WPA-PSK |
| pairwise=TKIP |
| group=TKIP |
| psk="not so secure passphrase" |
| wpa_ptk_rekey=600 |
| } |
| |
| # Only WPA-EAP is used. Both CCMP and TKIP is accepted. An AP that used WEP104 |
| # or WEP40 as the group cipher will not be accepted. |
| network={ |
| ssid="example" |
| proto=RSN |
| key_mgmt=WPA-EAP |
| pairwise=CCMP TKIP |
| group=CCMP TKIP |
| eap=TLS |
| identity="user@example.com" |
| ca_cert="/etc/cert/ca.pem" |
| client_cert="/etc/cert/user.pem" |
| private_key="/etc/cert/user.prv" |
| private_key_passwd="password" |
| priority=1 |
| } |
| |
| # EAP-PEAP/MSCHAPv2 configuration for RADIUS servers that use the new peaplabel |
| # (e.g., Radiator) |
| network={ |
| ssid="example" |
| key_mgmt=WPA-EAP |
| eap=PEAP |
| identity="user@example.com" |
| password="foobar" |
| ca_cert="/etc/cert/ca.pem" |
| phase1="peaplabel=1" |
| phase2="auth=MSCHAPV2" |
| priority=10 |
| } |
| |
| # EAP-TTLS/EAP-MD5-Challenge configuration with anonymous identity for the |
| # unencrypted use. Real identity is sent only within an encrypted TLS tunnel. |
| network={ |
| ssid="example" |
| key_mgmt=WPA-EAP |
| eap=TTLS |
| identity="user@example.com" |
| anonymous_identity="anonymous@example.com" |
| password="foobar" |
| ca_cert="/etc/cert/ca.pem" |
| priority=2 |
| } |
| |
| # EAP-TTLS/MSCHAPv2 configuration with anonymous identity for the unencrypted |
| # use. Real identity is sent only within an encrypted TLS tunnel. |
| network={ |
| ssid="example" |
| key_mgmt=WPA-EAP |
| eap=TTLS |
| identity="user@example.com" |
| anonymous_identity="anonymous@example.com" |
| password="foobar" |
| ca_cert="/etc/cert/ca.pem" |
| phase2="auth=MSCHAPV2" |
| } |
| |
| # WPA-EAP, EAP-TTLS with different CA certificate used for outer and inner |
| # authentication. |
| network={ |
| ssid="example" |
| key_mgmt=WPA-EAP |
| eap=TTLS |
| # Phase1 / outer authentication |
| anonymous_identity="anonymous@example.com" |
| ca_cert="/etc/cert/ca.pem" |
| # Phase 2 / inner authentication |
| phase2="autheap=TLS" |
| ca_cert2="/etc/cert/ca2.pem" |
| client_cert2="/etc/cer/user.pem" |
| private_key2="/etc/cer/user.prv" |
| private_key2_passwd="password" |
| priority=2 |
| } |
| |
| # Both WPA-PSK and WPA-EAP is accepted. Only CCMP is accepted as pairwise and |
| # group cipher. |
| network={ |
| ssid="example" |
| bssid=00:11:22:33:44:55 |
| proto=WPA RSN |
| key_mgmt=WPA-PSK WPA-EAP |
| pairwise=CCMP |
| group=CCMP |
| psk=06b4be19da289f475aa46a33cb793029d4ab3db7a23ee92382eb0106c72ac7bb |
| } |
| |
| # Special characters in SSID, so use hex string. Default to WPA-PSK, WPA-EAP |
| # and all valid ciphers. |
| network={ |
| ssid=00010203 |
| psk=000102030405060708090a0b0c0d0e0f101112131415161718191a1b1c1d1e1f |
| } |
| |
| |
| # EAP-SIM with a GSM SIM or USIM |
| network={ |
| ssid="eap-sim-test" |
| key_mgmt=WPA-EAP |
| eap=SIM |
| pin="1234" |
| pcsc="" |
| } |
| |
| |
| # EAP-PSK |
| network={ |
| ssid="eap-psk-test" |
| key_mgmt=WPA-EAP |
| eap=PSK |
| anonymous_identity="eap_psk_user" |
| password=06b4be19da289f475aa46a33cb793029 |
| identity="eap_psk_user@example.com" |
| } |
| |
| |
| # IEEE 802.1X/EAPOL with dynamically generated WEP keys (i.e., no WPA) using |
| # EAP-TLS for authentication and key generation; require both unicast and |
| # broadcast WEP keys. |
| network={ |
| ssid="1x-test" |
| key_mgmt=IEEE8021X |
| eap=TLS |
| identity="user@example.com" |
| ca_cert="/etc/cert/ca.pem" |
| client_cert="/etc/cert/user.pem" |
| private_key="/etc/cert/user.prv" |
| private_key_passwd="password" |
| eapol_flags=3 |
| } |
| |
| |
| # LEAP with dynamic WEP keys |
| network={ |
| ssid="leap-example" |
| key_mgmt=IEEE8021X |
| eap=LEAP |
| identity="user" |
| password="foobar" |
| } |
| |
| # EAP-IKEv2 using shared secrets for both server and peer authentication |
| network={ |
| ssid="ikev2-example" |
| key_mgmt=WPA-EAP |
| eap=IKEV2 |
| identity="user" |
| password="foobar" |
| } |
| |
| # EAP-FAST with WPA (WPA or WPA2) |
| network={ |
| ssid="eap-fast-test" |
| key_mgmt=WPA-EAP |
| eap=FAST |
| anonymous_identity="FAST-000102030405" |
| identity="username" |
| password="password" |
| phase1="fast_provisioning=1" |
| pac_file="/etc/wpa_supplicant.eap-fast-pac" |
| } |
| |
| network={ |
| ssid="eap-fast-test" |
| key_mgmt=WPA-EAP |
| eap=FAST |
| anonymous_identity="FAST-000102030405" |
| identity="username" |
| password="password" |
| phase1="fast_provisioning=1" |
| pac_file="blob://eap-fast-pac" |
| } |
| |
| # Plaintext connection (no WPA, no IEEE 802.1X) |
| network={ |
| ssid="plaintext-test" |
| key_mgmt=NONE |
| } |
| |
| |
| # Shared WEP key connection (no WPA, no IEEE 802.1X) |
| network={ |
| ssid="static-wep-test" |
| key_mgmt=NONE |
| wep_key0="abcde" |
| wep_key1=0102030405 |
| wep_key2="1234567890123" |
| wep_tx_keyidx=0 |
| priority=5 |
| } |
| |
| |
| # Shared WEP key connection (no WPA, no IEEE 802.1X) using Shared Key |
| # IEEE 802.11 authentication |
| network={ |
| ssid="static-wep-test2" |
| key_mgmt=NONE |
| wep_key0="abcde" |
| wep_key1=0102030405 |
| wep_key2="1234567890123" |
| wep_tx_keyidx=0 |
| priority=5 |
| auth_alg=SHARED |
| } |
| |
| |
| # IBSS/ad-hoc network with WPA-None/TKIP. |
| network={ |
| ssid="test adhoc" |
| mode=1 |
| frequency=2412 |
| proto=WPA |
| key_mgmt=WPA-NONE |
| pairwise=NONE |
| group=TKIP |
| psk="secret passphrase" |
| } |
| |
| |
| # Catch all example that allows more or less all configuration modes |
| network={ |
| ssid="example" |
| scan_ssid=1 |
| key_mgmt=WPA-EAP WPA-PSK IEEE8021X NONE |
| pairwise=CCMP TKIP |
| group=CCMP TKIP WEP104 WEP40 |
| psk="very secret passphrase" |
| eap=TTLS PEAP TLS |
| identity="user@example.com" |
| password="foobar" |
| ca_cert="/etc/cert/ca.pem" |
| client_cert="/etc/cert/user.pem" |
| private_key="/etc/cert/user.prv" |
| private_key_passwd="password" |
| phase1="peaplabel=0" |
| } |
| |
| # Example of EAP-TLS with smartcard (openssl engine) |
| network={ |
| ssid="example" |
| key_mgmt=WPA-EAP |
| eap=TLS |
| proto=RSN |
| pairwise=CCMP TKIP |
| group=CCMP TKIP |
| identity="user@example.com" |
| ca_cert="/etc/cert/ca.pem" |
| client_cert="/etc/cert/user.pem" |
| |
| engine=1 |
| |
| # The engine configured here must be available. Look at |
| # OpenSSL engine support in the global section. |
| # The key available through the engine must be the private key |
| # matching the client certificate configured above. |
| |
| # use the opensc engine |
| #engine_id="opensc" |
| #key_id="45" |
| |
| # use the pkcs11 engine |
| engine_id="pkcs11" |
| key_id="id_45" |
| |
| # Optional PIN configuration; this can be left out and PIN will be |
| # asked through the control interface |
| pin="1234" |
| } |
| |
| # Example configuration showing how to use an inlined blob as a CA certificate |
| # data instead of using external file |
| network={ |
| ssid="example" |
| key_mgmt=WPA-EAP |
| eap=TTLS |
| identity="user@example.com" |
| anonymous_identity="anonymous@example.com" |
| password="foobar" |
| ca_cert="blob://exampleblob" |
| priority=20 |
| } |
| |
| blob-base64-exampleblob={ |
| SGVsbG8gV29ybGQhCg== |
| } |
| |
| |
| # Wildcard match for SSID (plaintext APs only). This example select any |
| # open AP regardless of its SSID. |
| network={ |
| key_mgmt=NONE |
| } |