| /* |
| * Copyright 2012 Freescale Semiconductor, Inc. |
| * Copyright 2011 Linaro Ltd. |
| * |
| * The code contained herein is licensed under the GNU General Public |
| * License. You may obtain a copy of the GNU General Public License |
| * Version 2 or later at the following locations: |
| * |
| * http://www.opensource.org/licenses/gpl-license.html |
| * http://www.gnu.org/copyleft/gpl.html |
| */ |
| |
| / { |
| aliases { |
| mxcfb0 = &mxcfb1; |
| mxcfb1 = &mxcfb2; |
| mxcfb2 = &mxcfb3; |
| mxcfb3 = &mxcfb4; |
| }; |
| |
| memory { |
| reg = <0x10000000 0x80000000>; |
| }; |
| |
| backlight { |
| compatible = "pwm-backlight"; |
| pwms = <&pwm3 0 5000000>; |
| brightness-levels = <0 4 8 16 32 64 128 255>; |
| default-brightness-level = <7>; |
| }; |
| |
| clocks { |
| codec_osc: anaclk2 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <24576000>; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| home { |
| label = "Home"; |
| gpios = <&gpio1 11 1>; |
| linux,code = <102>; /* KEY_HOME */ |
| gpio-key,wakeup; |
| }; |
| |
| back { |
| label = "Back"; |
| gpios = <&gpio1 12 1>; |
| linux,code = <158>; /* KEY_BACK */ |
| gpio-key,wakeup; |
| }; |
| |
| program { |
| label = "Program"; |
| gpios = <&gpio2 12 1>; |
| linux,code = <362>; /* KEY_PROGRAM */ |
| gpio-key,wakeup; |
| }; |
| |
| volume-up { |
| label = "Volume Up"; |
| gpios = <&gpio2 15 1>; |
| linux,code = <115>; /* KEY_VOLUMEUP */ |
| gpio-key,wakeup; |
| }; |
| |
| volume-down { |
| label = "Volume Down"; |
| gpios = <&gpio5 14 1>; |
| linux,code = <114>; /* KEY_VOLUMEDOWN */ |
| gpio-key,wakeup; |
| }; |
| }; |
| |
| hannstar_cabc { |
| compatible = "hannstar,cabc"; |
| |
| lvds_share { |
| gpios = <&max7310_a 0 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| max7310_reset: max7310-reset { |
| compatible = "gpio-reset"; |
| reset-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; |
| reset-delay-us = <1>; |
| #reset-cells = <0>; |
| }; |
| |
| mxcfb1: fb@0 { |
| compatible = "fsl,mxc_sdc_fb"; |
| disp_dev = "ldb"; |
| interface_pix_fmt = "RGB666"; |
| default_bpp = <16>; |
| int_clk = <0>; |
| late_init = <0>; |
| status = "disabled"; |
| }; |
| |
| mxcfb2: fb@1 { |
| compatible = "fsl,mxc_sdc_fb"; |
| disp_dev = "hdmi"; |
| interface_pix_fmt = "RGB24"; |
| mode_str ="1920x1080M@60"; |
| default_bpp = <24>; |
| int_clk = <0>; |
| late_init = <0>; |
| status = "disabled"; |
| }; |
| |
| mxcfb3: fb@2 { |
| compatible = "fsl,mxc_sdc_fb"; |
| disp_dev = "lcd"; |
| interface_pix_fmt = "RGB565"; |
| mode_str ="CLAA-WVGA"; |
| default_bpp = <16>; |
| int_clk = <0>; |
| late_init = <0>; |
| status = "disabled"; |
| }; |
| |
| mxcfb4: fb@3 { |
| compatible = "fsl,mxc_sdc_fb"; |
| disp_dev = "ldb"; |
| interface_pix_fmt = "RGB666"; |
| default_bpp = <16>; |
| int_clk = <0>; |
| late_init = <0>; |
| status = "disabled"; |
| }; |
| |
| regulators { |
| compatible = "simple-bus"; |
| reg_audio: cs42888_supply { |
| compatible = "regulator-fixed"; |
| regulator-name = "cs42888_supply"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| si4763_vio1: vio1_tnr { |
| compatible = "regulator-fixed"; |
| regulator-name = "vio1"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| si4763_vio2: vio2_tnr { |
| compatible = "regulator-fixed"; |
| regulator-name = "vio2"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| si4763_vd: f3v3_tnr { |
| compatible = "regulator-fixed"; |
| regulator-name = "vd"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| si4763_va: f5v_tnr { |
| compatible = "regulator-fixed"; |
| regulator-name = "va"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-always-on; |
| }; |
| |
| reg_usb_h1_vbus: usb_h1_vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "usb_h1_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&max7310_b 7 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_usb_otg_vbus: usb_otg_vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "usb_otg_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&max7310_c 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_3p3v: 3p3v { |
| compatible = "regulator-fixed"; |
| regulator-name = "3P3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| reg_sd3_vmmc: sd3_vmmc{ |
| compatible = "regulator-fixed"; |
| regulator-name = "P3V3_SDa_SWITCHED"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| /* remove below line to enable this regulator */ |
| status="disabled"; |
| }; |
| }; |
| |
| sound-cs42888 { |
| compatible = "fsl,imx6-sabreauto-cs42888", |
| "fsl,imx-audio-cs42888"; |
| model = "imx-cs42888"; |
| esai-controller = <&esai>; |
| asrc-controller = <&asrc_p2p>; |
| audio-codec = <&codec>; |
| }; |
| |
| sound-fm { |
| compatible = "fsl,imx-audio-si476x", |
| "fsl,imx-tuner-si476x"; |
| model = "imx-radio-si4763"; |
| |
| ssi-controller = <&ssi2>; |
| fm-controller = <&si476x_codec>; |
| mux-int-port = <2>; |
| mux-ext-port = <5>; |
| }; |
| |
| sound-hdmi { |
| compatible = "fsl,imx6q-audio-hdmi", |
| "fsl,imx-audio-hdmi"; |
| model = "imx-audio-hdmi"; |
| hdmi-controller = <&hdmi_audio>; |
| }; |
| |
| sound-spdif { |
| compatible = "fsl,imx-audio-spdif", |
| "fsl,imx-sabreauto-spdif"; |
| model = "imx-spdif"; |
| spdif-controller = <&spdif>; |
| spdif-in; |
| }; |
| |
| v4l2_cap_0 { |
| compatible = "fsl,imx6q-v4l2-capture"; |
| ipu_id = <0>; |
| csi_id = <0>; |
| mclk_source = <0>; |
| status = "okay"; |
| }; |
| |
| v4l2_out { |
| compatible = "fsl,mxc_v4l2_output"; |
| status = "okay"; |
| }; |
| }; |
| |
| &audmux { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_audmux_3>; |
| status = "okay"; |
| }; |
| |
| &ecspi1 { |
| fsl,spi-num-chipselects = <1>; |
| cs-gpios = <&gpio3 19 0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi1_1 &pinctrl_ecspi1_cs_1>; |
| |
| flash: m25p80@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "st,m25p32"; |
| spi-max-frequency = <20000000>; |
| reg = <0>; |
| }; |
| }; |
| |
| &esai { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_esai_2>; |
| status = "okay"; |
| }; |
| |
| &fec { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_enet_2>; |
| phy-mode = "rgmii"; |
| status = "okay"; |
| }; |
| |
| &gpc { |
| fsl,cpu_pupscr_sw2iso = <0xf>; |
| fsl,cpu_pupscr_sw = <0xf>; |
| fsl,cpu_pdnscr_iso2sw = <0x1>; |
| fsl,cpu_pdnscr_iso = <0x1>; |
| }; |
| |
| &hdmi_audio { |
| status = "okay"; |
| }; |
| |
| &hdmi_cec { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_hdmi_cec_1>; |
| status = "okay"; |
| }; |
| |
| &hdmi_core { |
| ipu_id = <0>; |
| disp_id = <1>; |
| status = "okay"; |
| }; |
| |
| &hdmi_video { |
| fsl,phy_reg_vlev = <0x0294>; |
| fsl,phy_reg_cksymtx = <0x800d>; |
| status = "okay"; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2_3>; |
| status = "okay"; |
| |
| egalax_ts@04 { |
| compatible = "eeti,egalax_ts"; |
| reg = <0x04>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <28 2>; |
| wakeup-gpios = <&gpio2 28 0>; |
| }; |
| |
| pmic: pfuze100@08 { |
| compatible = "fsl,pfuze100"; |
| reg = <0x08>; |
| |
| regulators { |
| sw1a_reg: sw1ab { |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1875000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <6250>; |
| }; |
| |
| sw1c_reg: sw1c { |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1875000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <6250>; |
| }; |
| |
| sw2_reg: sw2 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw3a_reg: sw3a { |
| regulator-min-microvolt = <400000>; |
| regulator-max-microvolt = <1975000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw3b_reg: sw3b { |
| regulator-min-microvolt = <400000>; |
| regulator-max-microvolt = <1975000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw4_reg: sw4 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| swbst_reg: swbst { |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5150000>; |
| }; |
| |
| snvs_reg: vsnvs { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vref_reg: vrefddr { |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vgen1_reg: vgen1 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1550000>; |
| }; |
| |
| vgen2_reg: vgen2 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1550000>; |
| }; |
| |
| vgen3_reg: vgen3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| vgen4_reg: vgen4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| vgen5_reg: vgen5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| vgen6_reg: vgen6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| codec: cs42888@048 { |
| compatible = "cirrus,cs42888"; |
| reg = <0x048>; |
| clocks = <&codec_osc 0>; |
| clock-names = "mclk"; |
| VA-supply = <®_audio>; |
| VD-supply = <®_audio>; |
| VLS-supply = <®_audio>; |
| VLC-supply = <®_audio>; |
| }; |
| |
| hdmi: edid@50 { |
| compatible = "fsl,imx6-hdmi-i2c"; |
| reg = <0x50>; |
| }; |
| |
| si4763: si4763@63 { |
| compatible = "si4761"; |
| reg = <0x63>; |
| va-supply = <&si4763_va>; |
| vd-supply = <&si4763_vd>; |
| vio1-supply = <&si4763_vio1>; |
| vio2-supply = <&si4763_vio2>; |
| |
| si476x_codec: si476x-codec { |
| compatible = "si476x-codec"; |
| }; |
| }; |
| }; |
| |
| &i2c3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3_4>; |
| pinctrl-assert-gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| |
| max7310_a: gpio@30 { |
| compatible = "maxim,max7310"; |
| reg = <0x30>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| resets = <&max7310_reset>; |
| }; |
| |
| max7310_b: gpio@32 { |
| compatible = "maxim,max7310"; |
| reg = <0x32>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| max7310_c: gpio@34 { |
| compatible = "maxim,max7310"; |
| reg = <0x34>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| mma8451@1c { |
| compatible = "fsl,mma8451"; |
| reg = <0x1c>; |
| position = <7>; |
| interrupt-parent = <&gpio6>; |
| interrupts = <31 8>; |
| interrupt-route = <1>; |
| }; |
| |
| mag3110@0e { |
| compatible = "fsl,mag3110"; |
| reg = <0x0e>; |
| position = <2>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <29 1>; |
| }; |
| |
| isl29023@44 { |
| compatible = "fsl,isl29023"; |
| reg = <0x44>; |
| rext = <499>; |
| interrupt-parent = <&gpio5>; |
| interrupts = <17 2>; |
| }; |
| |
| adv7180: adv7180@21 { |
| compatible = "adv,adv7180"; |
| reg = <0x21>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ipu1_3>; |
| clocks = <&clks 201>; |
| clock-names = "csi_mclk"; |
| DOVDD-supply = <®_3p3v>; /* 3.3v, enabled via 2.8 VGEN6 */ |
| AVDD-supply = <®_3p3v>; /* 1.8v */ |
| DVDD-supply = <®_3p3v>; /* 1.8v */ |
| PVDD-supply = <®_3p3v>; /* 1.8v */ |
| pwn-gpios = <&max7310_b 2 0>; |
| csi_id = <0>; |
| mclk = <24000000>; |
| mclk_source = <0>; |
| cvbs = <1>; |
| }; |
| }; |
| |
| &iomuxc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_hog>; |
| |
| hog { |
| pinctrl_hog: hoggrp { |
| fsl,pins = < |
| MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1f059 |
| MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x80000000 |
| MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x80000000 |
| MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x80000000 |
| MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x80000000 |
| MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x80000000 |
| MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x80000000 |
| MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x80000000 |
| MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x80000000 |
| MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x80000000 |
| MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x80000000 |
| MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x80000000 |
| MX6QDL_PAD_GPIO_18__SD3_VSELECT 0x17059 |
| MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x17059 |
| MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x17059 |
| MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x80000000 |
| MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x80000000 |
| >; |
| }; |
| }; |
| }; |
| |
| &flexcan1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan1_1>; |
| pinctrl-assert-gpios = <&max7310_b 3 GPIO_ACTIVE_HIGH>; /* TX */ |
| trx-en-gpio = <&max7310_b 6 GPIO_ACTIVE_HIGH>; |
| trx-stby-gpio = <&max7310_b 5 GPIO_ACTIVE_HIGH>; |
| status = "disabled"; /* pin conflict with fec */ |
| }; |
| |
| &flexcan2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan2_1>; |
| trx-en-gpio = <&max7310_c 6 GPIO_ACTIVE_HIGH>; |
| trx-stby-gpio = <&max7310_c 5 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| &ldb { |
| status = "okay"; |
| |
| lvds-channel@0 { |
| fsl,data-mapping = "spwg"; |
| fsl,data-width = <18>; |
| primary; |
| status = "okay"; |
| |
| display-timings { |
| native-mode = <&timing0>; |
| timing0: hsd100pxn1 { |
| clock-frequency = <65000000>; |
| hactive = <1024>; |
| vactive = <768>; |
| hback-porch = <220>; |
| hfront-porch = <40>; |
| vback-porch = <21>; |
| vfront-porch = <7>; |
| hsync-len = <60>; |
| vsync-len = <10>; |
| }; |
| }; |
| }; |
| |
| lvds-channel@1 { |
| fsl,data-mapping = "spwg"; |
| fsl,data-width = <18>; |
| status = "okay"; |
| |
| display-timings { |
| native-mode = <&timing1>; |
| timing1: hsd100pxn1 { |
| clock-frequency = <65000000>; |
| hactive = <1024>; |
| vactive = <768>; |
| hback-porch = <220>; |
| hfront-porch = <40>; |
| vback-porch = <21>; |
| vfront-porch = <7>; |
| hsync-len = <60>; |
| vsync-len = <10>; |
| }; |
| }; |
| }; |
| }; |
| |
| &dcic1 { |
| dcic_id = <0>; |
| dcic_mux = "dcic-hdmi"; |
| status = "okay"; |
| }; |
| |
| &dcic2 { |
| dcic_id = <1>; |
| dcic_mux = "dcic-lvds0"; |
| status = "okay"; |
| }; |
| |
| &mlb { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mlb_2>; |
| status = "okay"; |
| }; |
| |
| &pcie { |
| status = "okay"; |
| }; |
| |
| &pwm3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm3_1>; |
| status = "okay"; |
| }; |
| |
| &spdif { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spdif_1>; |
| status = "okay"; |
| }; |
| |
| &ssi2 { |
| fsl,mode = "i2s-master"; |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3_1>; |
| pinctrl-assert-gpios = <&max7310_b 4 GPIO_ACTIVE_HIGH>, /* CTS */ |
| <&max7310_c 3 GPIO_ACTIVE_HIGH>; /* RXD and TXD */ |
| fsl,uart-has-rtscts; |
| status = "okay"; |
| /* for DTE mode, add below change */ |
| /* fsl,dte-mode; */ |
| /* pinctrl-0 = <&pinctrl_uart3dte_1>; */ |
| }; |
| |
| &gpmi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpmi_nand_1>; |
| status = "disabled"; /* pin conflict with uart3 */ |
| nand-on-flash-bbt; |
| }; |
| |
| &uart4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart4_1>; |
| status = "okay"; |
| }; |
| |
| &usbh1 { |
| vbus-supply = <®_usb_h1_vbus>; |
| status = "okay"; |
| }; |
| |
| &usbotg { |
| vbus-supply = <®_usb_otg_vbus>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotg_2>; |
| imx6-usb-charger-detection; |
| status = "okay"; |
| }; |
| |
| &usdhc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc1_1>; |
| cd-gpios = <&gpio1 1 0>; |
| wp-gpios = <&gpio5 20 0>; |
| no-1-8-v; |
| keep-power-in-suspend; |
| enable-sdio-wakeup; |
| status = "okay"; |
| }; |
| |
| &usdhc3 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc3_1>; |
| pinctrl-1 = <&pinctrl_usdhc3_1_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc3_1_200mhz>; |
| cd-gpios = <&gpio6 15 0>; |
| wp-gpios = <&gpio1 13 0>; |
| /* |
| * Due to board issue, we can not use external regulator for card slot |
| * by default since the card power is shared with card detect pullup. |
| * Disabling the vmmc regulator will cause unexpected card detect |
| * interrupts. |
| * HW rework is needed to fix this isssue. Remove R695 first, then you |
| * can open below line to enable the using of external regulator. |
| * Then you will be able to power off the card during suspend. This is |
| * especially needed for a SD3.0 card re-enumeration working on UHS mode |
| * Note: reg_sd3_vmmc is also need to be enabled |
| */ |
| /* vmmc-supply = <®_sd3_vmmc>; */ |
| keep-power-in-suspend; |
| enable-sdio-wakeup; |
| status = "okay"; |
| }; |
| |
| &weim { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_weim_nor_1 &pinctrl_weim_cs0_1>; |
| #address-cells = <2>; |
| #size-cells = <1>; |
| ranges = <0 0 0x08000000 0x08000000>; |
| status = "disabled"; /* pin conflict with ecspi1, i2c3 and uart3 */ |
| |
| nor@0,0 { |
| compatible = "cfi-flash"; |
| reg = <0 0 0x02000000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| bank-width = <2>; |
| fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000 |
| 0x0000c000 0x1404a38e 0x00000000>; |
| }; |
| }; |