blob: 01a1a16ab7be8fcc4ae7df6a2782caa377b271a7 [file] [log] [blame]
#
# Light sensors
#
# When adding new entries keep the list in alphabetical order
menu "Light sensors"
config ADJD_S311
tristate "ADJD-S311-CR999 digital color sensor"
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
depends on I2C
help
If you say yes here you get support for the Avago ADJD-S311-CR999
digital color light sensor.
This driver can also be built as a module. If so, the module
will be called adjd_s311.
config AL3320A
tristate "AL3320A ambient light sensor"
depends on I2C
help
Say Y here if you want to build a driver for the Dyna Image AL3320A
ambient light sensor.
To compile this driver as a module, choose M here: the
module will be called al3320a.
config APDS9300
tristate "APDS9300 ambient light sensor"
depends on I2C
help
Say Y here if you want to build a driver for the Avago APDS9300
ambient light sensor.
To compile this driver as a module, choose M here: the
module will be called apds9300.
config CM32181
depends on I2C
tristate "CM32181 driver"
help
Say Y here if you use cm32181.
This option enables ambient light sensor using
Capella cm32181 device driver.
To compile this driver as a module, choose M here:
the module will be called cm32181.
config CM3232
depends on I2C
tristate "CM3232 ambient light sensor"
help
Say Y here if you use cm3232.
This option enables ambient light sensor using
Capella Microsystems cm3232 device driver.
To compile this driver as a module, choose M here:
the module will be called cm3232.
config CM3323
depends on I2C
tristate "Capella CM3323 color light sensor"
help
Say Y here if you want to build a driver for Capela CM3323
color sensor.
To compile this driver as a module, choose M here: the module will
be called cm3323.
config CM36651
depends on I2C
tristate "CM36651 driver"
help
Say Y here if you use cm36651.
This option enables proximity & RGB sensor using
Capella cm36651 device driver.
To compile this driver as a module, choose M here:
the module will be called cm36651.
config GP2AP020A00F
tristate "Sharp GP2AP020A00F Proximity/ALS sensor"
depends on I2C
select REGMAP_I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
select IRQ_WORK
help
Say Y here if you have a Sharp GP2AP020A00F proximity/ALS combo-chip
hooked to an I2C bus.
To compile this driver as a module, choose M here: the
module will be called gp2ap020a00f.
config ISL29125
tristate "Intersil ISL29125 digital color light sensor"
depends on I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
Say Y here if you want to build a driver for the Intersil ISL29125
RGB light sensor for I2C.
To compile this driver as a module, choose M here: the module will be
called isl29125.
config HID_SENSOR_ALS
depends on HID_SENSOR_HUB
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
select HID_SENSOR_IIO_COMMON
select HID_SENSOR_IIO_TRIGGER
tristate "HID ALS"
help
Say yes here to build support for the HID SENSOR
Ambient light sensor.
To compile this driver as a module, choose M here: the
module will be called hid-sensor-als.
config HID_SENSOR_PROX
depends on HID_SENSOR_HUB
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
select HID_SENSOR_IIO_COMMON
select HID_SENSOR_IIO_TRIGGER
tristate "HID PROX"
help
Say yes here to build support for the HID SENSOR
Proximity sensor.
To compile this driver as a module, choose M here: the
module will be called hid-sensor-prox.
config JSA1212
tristate "JSA1212 ALS and proximity sensor driver"
depends on I2C
select REGMAP_I2C
help
Say Y here if you want to build a IIO driver for JSA1212
proximity & ALS sensor device.
To compile this driver as a module, choose M here:
the module will be called jsa1212.
config SENSORS_LM3533
tristate "LM3533 ambient light sensor"
depends on MFD_LM3533
help
If you say yes here you get support for the ambient light sensor
interface on National Semiconductor / TI LM3533 Lighting Power
chips.
The sensor interface can be used to control the LEDs and backlights
of the chip through defining five light zones and three sets of
corresponding output-current values.
The driver provides raw and mean adc readings along with the current
light zone through sysfs. A threshold event can be generated on zone
changes. The ALS-control output values can be set per zone for the
three current output channels.
config LTR501
tristate "LTR-501ALS-01 light sensor"
depends on I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
If you say yes here you get support for the Lite-On LTR-501ALS-01
ambient light and proximity sensor.
This driver can also be built as a module. If so, the module
will be called ltr501.
config TCS3414
tristate "TAOS TCS3414 digital color sensor"
depends on I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
If you say yes here you get support for the TAOS TCS3414
family of digital color sensors.
This driver can also be built as a module. If so, the module
will be called tcs3414.
config TCS3472
tristate "TAOS TCS3472 color light-to-digital converter"
depends on I2C
select IIO_BUFFER
select IIO_TRIGGERED_BUFFER
help
If you say yes here you get support for the TAOS TCS3472
family of color light-to-digital converters with IR filter.
This driver can also be built as a module. If so, the module
will be called tcs3472.
config SENSORS_TSL2563
tristate "TAOS TSL2560, TSL2561, TSL2562 and TSL2563 ambient light sensors"
depends on I2C
help
If you say yes here you get support for the Taos TSL2560,
TSL2561, TSL2562 and TSL2563 ambient light sensors.
This driver can also be built as a module. If so, the module
will be called tsl2563.
config TSL4531
tristate "TAOS TSL4531 ambient light sensors"
depends on I2C
help
Say Y here if you want to build a driver for the TAOS TSL4531 family
of ambient light sensors with direct lux output.
To compile this driver as a module, choose M here: the
module will be called tsl4531.
config VCNL4000
tristate "VCNL4000 combined ALS and proximity sensor"
depends on I2C
help
Say Y here if you want to build a driver for the Vishay VCNL4000
combined ambient light and proximity sensor.
To compile this driver as a module, choose M here: the
module will be called vcnl4000.
endmenu