blob: 0067ea46e0ccbfe8a0a319fbd991b96833d5b587 [file] [log] [blame] [edit]
/*
* siemens rut
* (C) Copyright 2013 Siemens Schweiz AG
* (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* Based on:
* U-Boot file:/include/configs/am335x_evm.h
*
* Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_RUT_H
#define __CONFIG_RUT_H
#define CONFIG_SIEMENS_RUT
#define MACH_TYPE_RUT 4316
#define CONFIG_SIEMENS_MACH_TYPE MACH_TYPE_RUT
#include "siemens-am33x-common.h"
#define CONFIG_SYS_MPUCLK 600
#define RUT_IOCTRL_VAL 0x18b
#define DDR_PLL_FREQ 303
/* Physical Memory Map */
#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MiB */
/* I2C Configuration */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200
#undef CONFIG_SPL_NET_SUPPORT
#undef CONFIG_SPL_NET_VCI_STRING
#undef CONFIG_SPL_ETH_SUPPORT
#define CONFIG_PHY_NATSEMI
#define CONFIG_FACTORYSET
/* UBI Support */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_PARTITIONS
#define CONFIG_MTD_DEVICE
#define CONFIG_RBTREE
#define CONFIG_LZO
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#endif
/* Watchdog */
#define WATCHDOG_TRIGGER_GPIO 14
#ifndef CONFIG_SPL_BUILD
/* Default env settings */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hostname=rut\0" \
"nand_img_size=0x500000\0" \
"splashpos=m,m\0" \
"optargs=fixrtc --no-log consoleblank=0 \0" \
CONFIG_COMMON_ENV_SETTINGS \
"mmc_dev=0\0" \
"mmc_root=/dev/mmcblk0p2 rw\0" \
"mmc_root_fs_type=ext4 rootwait\0" \
"mmc_load_uimage=" \
"mmc rescan; " \
"setenv bootfile uImage;" \
"fatload mmc ${mmc_dev} ${kloadaddr} ${bootfile}\0" \
"loadbootenv=fatload mmc ${mmc_dev} ${loadaddr} ${bootenv}\0" \
"importbootenv=echo Importing environment from mmc ...; " \
"env import -t $loadaddr $filesize\0" \
"mmc_args=run bootargs_defaults;" \
"mtdparts default;" \
"setenv bootargs ${bootargs} " \
"root=${mmc_root} ${mtdparts}" \
"rootfstype=${mmc_root_fs_type} ip=${ip_method} " \
"eth=${ethaddr} " \
"\0" \
"mmc_boot=run mmc_args; " \
"run mmc_load_uimage; " \
"bootm ${kloadaddr}\0" \
""
#ifndef CONFIG_RESTORE_FLASH
/* set to negative value for no autoboot */
#define CONFIG_BOOTDELAY 3
#define CONFIG_BOOTCOMMAND \
"if mmc rescan; then " \
"echo SD/MMC found on device ${mmc_dev};" \
"if run loadbootenv; then " \
"echo Loaded environment from ${bootenv};" \
"run importbootenv;" \
"fi;" \
"if test -n $uenvcmd; then " \
"echo Running uenvcmd ...;" \
"run uenvcmd;" \
"fi;" \
"if run mmc_load_uimage; then " \
"run mmc_args;" \
"bootm ${kloadaddr};" \
"fi;" \
"fi;" \
"run nand_boot;" \
"reset;"
#else
#define CONFIG_BOOTDELAY 0
#define CONFIG_BOOTCOMMAND \
"setenv autoload no; " \
"dhcp; " \
"if tftp 80000000 debrick.scr; then " \
"source 80000000; " \
"fi"
#endif
#endif /* CONFIG_SPL_BUILD */
#ifdef CONFIG_SPL_BUILD
#undef CONFIG_HW_WATCHDOG
#endif
#define CONFIG_VIDEO
#if defined(CONFIG_VIDEO)
#define CONFIG_VIDEO_DA8XX
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_CMD_BMP
#define DA8XX_LCD_CNTL_BASE LCD_CNTL_BASE
#define CONFIG_SPI
#define CONFIG_OMAP3_SPI
#define BOARD_LCD_RESET 115 /* Bank 3 pin 19 */
#define CONFIG_ARCH_EARLY_INIT_R
#define CONFIG_FORMIKE
#define DISPL_PLL_SPREAD_SPECTRUM
#define CONFIG_SYS_CONSOLE_BG_COL 0xff
#define CONFIG_SYS_CONSOLE_FG_COL 0x00
#endif
#ifndef CONFIG_SPL_BUILD
#define CONFIG_FIT
#endif
#endif /* ! __CONFIG_RUT_H */