| # Copyright 2007 Simtec Electronics | |
| # | |
| # Licensed under GPLv2 | |
| config CPU_S3C2410 | |
| bool | |
| depends on ARCH_S3C2410 | |
| select CPU_ARM920T | |
| select S3C_GPIO_PULL_UP | |
| select S3C2410_CLOCK | |
| select S3C2410_GPIO | |
| select CPU_LLSERIAL_S3C2410 | |
| select S3C2410_PM if PM | |
| select S3C2410_CPUFREQ if CPU_FREQ_S3C24XX | |
| help | |
| Support for S3C2410 and S3C2410A family from the S3C24XX line | |
| of Samsung Mobile CPUs. | |
| config CPU_S3C2410_DMA | |
| bool | |
| depends on S3C2410_DMA && (CPU_S3C2410 || CPU_S3C2442) | |
| default y if CPU_S3C2410 || CPU_S3C2442 | |
| help | |
| DMA device selection for S3C2410 and compatible CPUs | |
| config S3C2410_PM | |
| bool | |
| help | |
| Power Management code common to S3C2410 and better | |
| config S3C2410_GPIO | |
| bool | |
| help | |
| GPIO code for S3C2410 and similar processors | |
| config SIMTEC_NOR | |
| bool | |
| help | |
| Internal node to specify machine has simtec NOR mapping | |
| config MACH_BAST_IDE | |
| bool | |
| select HAVE_PATA_PLATFORM | |
| help | |
| Internal node for machines with an BAST style IDE | |
| interface | |
| # cpu frequency scaling support | |
| config S3C2410_CPUFREQ | |
| bool | |
| depends on CPU_FREQ_S3C24XX && CPU_S3C2410 | |
| select S3C2410_CPUFREQ_UTILS | |
| help | |
| CPU Frequency scaling support for S3C2410 | |
| config S3C2410_PLLTABLE | |
| bool | |
| depends on S3C2410_CPUFREQ && CPU_FREQ_S3C24XX_PLL | |
| default y | |
| help | |
| Select the PLL table for the S3C2410 | |
| menu "S3C2410 Machines" | |
| config ARCH_SMDK2410 | |
| bool "SMDK2410/A9M2410" | |
| select CPU_S3C2410 | |
| select MACH_SMDK | |
| help | |
| Say Y here if you are using the SMDK2410 or the derived module A9M2410 | |
| <http://www.fsforth.de> | |
| config ARCH_H1940 | |
| bool "IPAQ H1940" | |
| select CPU_S3C2410 | |
| select PM_H1940 if PM | |
| select S3C_DEV_USB_HOST | |
| select S3C_DEV_NAND | |
| select S3C2410_SETUP_TS | |
| help | |
| Say Y here if you are using the HP IPAQ H1940 | |
| config H1940BT | |
| tristate "Control the state of H1940 bluetooth chip" | |
| depends on ARCH_H1940 | |
| select RFKILL | |
| help | |
| This is a simple driver that is able to control | |
| the state of built in bluetooth chip on h1940. | |
| config PM_H1940 | |
| bool | |
| help | |
| Internal node for H1940 and related PM | |
| config MACH_N30 | |
| bool "Acer N30 family" | |
| select CPU_S3C2410 | |
| select MACH_N35 | |
| select S3C_DEV_USB_HOST | |
| select S3C_DEV_NAND | |
| help | |
| Say Y here if you want suppt for the Acer N30, Acer N35, | |
| Navman PiN570, Yakumo AlphaX or Airis NC05 PDAs. | |
| config MACH_N35 | |
| bool | |
| help | |
| Internal node in order to enable support for Acer N35 if Acer N30 is | |
| selected. | |
| config ARCH_BAST | |
| bool "Simtec Electronics BAST (EB2410ITX)" | |
| select CPU_S3C2410 | |
| select S3C2410_IOTIMING if S3C2410_CPUFREQ | |
| select PM_SIMTEC if PM | |
| select SIMTEC_NOR | |
| select MACH_BAST_IDE | |
| select S3C24XX_DCLK | |
| select ISA | |
| select S3C_DEV_HWMON | |
| select S3C_DEV_USB_HOST | |
| select S3C_DEV_NAND | |
| help | |
| Say Y here if you are using the Simtec Electronics EB2410ITX | |
| development board (also known as BAST) | |
| config MACH_OTOM | |
| bool "NexVision OTOM Board" | |
| select CPU_S3C2410 | |
| select S3C_DEV_USB_HOST | |
| select S3C_DEV_NAND | |
| help | |
| Say Y here if you are using the Nex Vision OTOM board | |
| config MACH_AML_M5900 | |
| bool "AML M5900 Series" | |
| select CPU_S3C2410 | |
| select PM_SIMTEC if PM | |
| select S3C_DEV_USB_HOST | |
| help | |
| Say Y here if you are using the American Microsystems M5900 Series | |
| <http://www.amltd.com> | |
| config BAST_PC104_IRQ | |
| bool "BAST PC104 IRQ support" | |
| depends on ARCH_BAST | |
| default y | |
| help | |
| Say Y here to enable the PC104 IRQ routing on the | |
| Simtec BAST (EB2410ITX) | |
| config MACH_TCT_HAMMER | |
| bool "TCT Hammer Board" | |
| select CPU_S3C2410 | |
| select S3C_DEV_USB_HOST | |
| help | |
| Say Y here if you are using the TinCanTools Hammer Board | |
| <http://www.tincantools.com> | |
| config MACH_VR1000 | |
| bool "Thorcom VR1000" | |
| select PM_SIMTEC if PM | |
| select S3C24XX_DCLK | |
| select SIMTEC_NOR | |
| select MACH_BAST_IDE | |
| select CPU_S3C2410 | |
| select S3C_DEV_USB_HOST | |
| help | |
| Say Y here if you are using the Thorcom VR1000 board. | |
| config MACH_QT2410 | |
| bool "QT2410" | |
| select CPU_S3C2410 | |
| select S3C_DEV_USB_HOST | |
| select S3C_DEV_NAND | |
| help | |
| Say Y here if you are using the Armzone QT2410 | |
| endmenu |