blob: 1cf70a9f5d5056aa6c2b77a87bc1b88f30821aa4 [file] [log] [blame] [edit]
/*
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <netdev.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#define DDR_BASE_CS_OFF(n) (0x0000 + ((n) << 3))
#define DDR_SIZE_CS_OFF(n) (0x0004 + ((n) << 3))
static struct mbus_win windows[] = {
/* PCIE MEM address space */
{ DEFADR_PCI_MEM, 256 << 20, CPU_TARGET_PCIE13, CPU_ATTR_PCIE_MEM },
/* PCIE IO address space */
{ DEFADR_PCI_IO, 64 << 10, CPU_TARGET_PCIE13, CPU_ATTR_PCIE_IO },
/* SPI */
{ DEFADR_SPIF, 8 << 20, CPU_TARGET_DEVICEBUS_BOOTROM_SPI,
CPU_ATTR_SPIFLASH },
/* NOR */
{ DEFADR_BOOTROM, 8 << 20, CPU_TARGET_DEVICEBUS_BOOTROM_SPI,
CPU_ATTR_BOOTROM },
};
void reset_cpu(unsigned long ignored)
{
struct mvebu_system_registers *reg =
(struct mvebu_system_registers *)MVEBU_SYSTEM_REG_BASE;
writel(readl(&reg->rstoutn_mask) | 1, &reg->rstoutn_mask);
writel(readl(&reg->sys_soft_rst) | 1, &reg->sys_soft_rst);
while (1)
;
}
#if defined(CONFIG_DISPLAY_CPUINFO)
int print_cpuinfo(void)
{
u16 devid = (readl(MVEBU_REG_PCIE_DEVID) >> 16) & 0xffff;
u8 revid = readl(MVEBU_REG_PCIE_REVID) & 0xff;
puts("SoC: ");
switch (devid) {
case SOC_MV78460_ID:
puts("MV78460-");
break;
default:
puts("Unknown-");
break;
}
switch (revid) {
case 1:
puts("A0\n");
break;
case 2:
puts("B0\n");
break;
default:
puts("??\n");
break;
}
return 0;
}
#endif /* CONFIG_DISPLAY_CPUINFO */
/*
* This function initialize Controller DRAM Fastpath windows.
* It takes the CS size information from the 0x1500 scratch registers
* and sets the correct windows sizes and base addresses accordingly.
*
* These values are set in the scratch registers by the Marvell
* DDR3 training code, which is executed by the BootROM before the
* main payload (U-Boot) is executed. This training code is currently
* only available in the Marvell U-Boot version. It needs to be
* ported to mainline U-Boot SPL at some point.
*/
static void update_sdram_window_sizes(void)
{
u64 base = 0;
u32 size, temp;
int i;
for (i = 0; i < SDRAM_MAX_CS; i++) {
size = readl((MVEBU_SDRAM_SCRATCH + (i * 8))) & SDRAM_ADDR_MASK;
if (size != 0) {
size |= ~(SDRAM_ADDR_MASK);
/* Set Base Address */
temp = (base & 0xFF000000ll) | ((base >> 32) & 0xF);
writel(temp, MVEBU_SDRAM_BASE + DDR_BASE_CS_OFF(i));
/*
* Check if out of max window size and resize
* the window
*/
temp = (readl(MVEBU_SDRAM_BASE + DDR_SIZE_CS_OFF(i)) &
~(SDRAM_ADDR_MASK)) | 1;
temp |= (size & SDRAM_ADDR_MASK);
writel(temp, MVEBU_SDRAM_BASE + DDR_SIZE_CS_OFF(i));
base += ((u64)size + 1);
} else {
/*
* Disable window if not used, otherwise this
* leads to overlapping enabled windows with
* pretty strange results
*/
clrbits_le32(MVEBU_SDRAM_BASE + DDR_SIZE_CS_OFF(i), 1);
}
}
}
#ifdef CONFIG_ARCH_CPU_INIT
int arch_cpu_init(void)
{
/* Linux expects the internal registers to be at 0xf1000000 */
writel(SOC_REGS_PHY_BASE, INTREG_BASE_ADDR_REG);
/*
* We need to call mvebu_mbus_probe() before calling
* update_sdram_window_sizes() as it disables all previously
* configured mbus windows and then configures them as
* required for U-Boot. Calling update_sdram_window_sizes()
* without this configuration will not work, as the internal
* registers can't be accessed reliably because of potenial
* double mapping.
* After updating the SDRAM access windows we need to call
* mvebu_mbus_probe() again, as this now correctly configures
* the SDRAM areas that are later used by the MVEBU drivers
* (e.g. USB, NETA).
*/
/*
* First disable all windows
*/
mvebu_mbus_probe(NULL, 0);
/*
* Now the SDRAM access windows can be reconfigured using
* the information in the SDRAM scratch pad registers
*/
update_sdram_window_sizes();
/*
* Finally the mbus windows can be configured with the
* updated SDRAM sizes
*/
mvebu_mbus_probe(windows, ARRAY_SIZE(windows));
return 0;
}
#endif /* CONFIG_ARCH_CPU_INIT */
/*
* SOC specific misc init
*/
#if defined(CONFIG_ARCH_MISC_INIT)
int arch_misc_init(void)
{
/* Nothing yet, perhaps we need something here later */
return 0;
}
#endif /* CONFIG_ARCH_MISC_INIT */
#ifdef CONFIG_MVNETA
int cpu_eth_init(bd_t *bis)
{
mvneta_initialize(bis, MVEBU_EGIGA0_BASE, 0, CONFIG_PHY_BASE_ADDR + 0);
mvneta_initialize(bis, MVEBU_EGIGA1_BASE, 1, CONFIG_PHY_BASE_ADDR + 1);
mvneta_initialize(bis, MVEBU_EGIGA2_BASE, 2, CONFIG_PHY_BASE_ADDR + 2);
mvneta_initialize(bis, MVEBU_EGIGA3_BASE, 3, CONFIG_PHY_BASE_ADDR + 3);
return 0;
}
#endif
#ifndef CONFIG_SYS_DCACHE_OFF
void enable_caches(void)
{
/* Enable D-cache. I-cache is already enabled in start.S */
dcache_enable();
}
#endif