blob: f5bc6728b7c2ce4cbe4bcbdef260b39d1cfc1e32 [file] [log] [blame] [edit]
/*
* Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
*
* (C) Copyright 2009 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <config.h>
#include <asm/arch/imx-regs.h>
#include <generated/asm-offsets.h>
#include <linux/linkage.h>
.section ".text.init", "x"
.macro init_arm_erratum
/* ARM erratum ID #468414 */
mrc 15, 0, r1, c1, c0, 1
orr r1, r1, #(1 << 5) /* enable L1NEON bit */
mcr 15, 0, r1, c1, c0, 1
.endm
/*
* L2CC Cache setup/invalidation/disable
*/
.macro init_l2cc
/* explicitly disable L2 cache */
mrc 15, 0, r0, c1, c0, 1
bic r0, r0, #0x2
mcr 15, 0, r0, c1, c0, 1
/* reconfigure L2 cache aux control reg */
ldr r0, =0xC0 | /* tag RAM */ \
0x4 | /* data RAM */ \
1 << 24 | /* disable write allocate delay */ \
1 << 23 | /* disable write allocate combine */ \
1 << 22 /* disable write allocate */
#if defined(CONFIG_MX51)
ldr r3, [r4, #ROM_SI_REV]
cmp r3, #0x10
/* disable write combine for TO 2 and lower revs */
orrls r0, r0, #1 << 25
#endif
mcr 15, 1, r0, c9, c0, 2
/* enable L2 cache */
mrc 15, 0, r0, c1, c0, 1
orr r0, r0, #2
mcr 15, 0, r0, c1, c0, 1
.endm /* init_l2cc */
/* AIPS setup - Only setup MPROTx registers.
* The PACR default values are good.*/
.macro init_aips
/*
* Set all MPROTx to be non-bufferable, trusted for R/W,
* not forced to user-mode.
*/
ldr r0, =AIPS1_BASE_ADDR
ldr r1, =0x77777777
str r1, [r0, #0x0]
str r1, [r0, #0x4]
ldr r0, =AIPS2_BASE_ADDR
str r1, [r0, #0x0]
str r1, [r0, #0x4]
/*
* Clear the on and off peripheral modules Supervisor Protect bit
* for SDMA to access them. Did not change the AIPS control registers
* (offset 0x20) access type
*/
.endm /* init_aips */
/* M4IF setup */
.macro init_m4if
#ifdef CONFIG_MX51
/* VPU and IPU given higher priority (0x4)
* IPU accesses with ID=0x1 given highest priority (=0xA)
*/
ldr r0, =M4IF_BASE_ADDR
ldr r1, =0x00000203
str r1, [r0, #0x40]
str r4, [r0, #0x44]
ldr r1, =0x00120125
str r1, [r0, #0x9C]
ldr r1, =0x001901A3
str r1, [r0, #0x48]
#endif
.endm /* init_m4if */
.macro setup_pll pll, freq
ldr r0, =\pll
adr r2, W_DP_\freq
bl setup_pll_func
.endm
#define W_DP_OP 0
#define W_DP_MFD 4
#define W_DP_MFN 8
setup_pll_func:
ldr r1, =0x00001232
str r1, [r0, #PLL_DP_CTL] /* Set DPLL ON (set UPEN bit): BRMO=1 */
mov r1, #0x2
str r1, [r0, #PLL_DP_CONFIG] /* Enable auto-restart AREN bit */
ldr r1, [r2, #W_DP_OP]
str r1, [r0, #PLL_DP_OP]
str r1, [r0, #PLL_DP_HFS_OP]
ldr r1, [r2, #W_DP_MFD]
str r1, [r0, #PLL_DP_MFD]
str r1, [r0, #PLL_DP_HFS_MFD]
ldr r1, [r2, #W_DP_MFN]
str r1, [r0, #PLL_DP_MFN]
str r1, [r0, #PLL_DP_HFS_MFN]
ldr r1, =0x00001232
str r1, [r0, #PLL_DP_CTL]
1: ldr r1, [r0, #PLL_DP_CTL]
ands r1, r1, #0x1
beq 1b
/* r10 saved upper lr */
mov pc, lr
.macro setup_pll_errata pll, freq
ldr r2, =\pll
str r4, [r2, #PLL_DP_CONFIG] /* Disable auto-restart AREN bit */
ldr r1, =0x00001236
str r1, [r2, #PLL_DP_CTL] /* Restart PLL with PLM=1 */
1: ldr r1, [r2, #PLL_DP_CTL] /* Wait for lock */
ands r1, r1, #0x1
beq 1b
ldr r5, \freq
str r5, [r2, #PLL_DP_MFN] /* Modify MFN value */
str r5, [r2, #PLL_DP_HFS_MFN]
mov r1, #0x1
str r1, [r2, #PLL_DP_CONFIG] /* Reload MFN value */
2: ldr r1, [r2, #PLL_DP_CONFIG]
tst r1, #1
bne 2b
ldr r1, =100 /* Wait at least 4 us */
3: subs r1, r1, #1
bge 3b
mov r1, #0x2
str r1, [r2, #PLL_DP_CONFIG] /* Enable auto-restart AREN bit */
.endm
.macro init_clock
#if defined (CONFIG_MX51)
ldr r0, =CCM_BASE_ADDR
/* Gate of clocks to the peripherals first */
ldr r1, =0x3FFFFFFF
str r1, [r0, #CLKCTL_CCGR0]
str r4, [r0, #CLKCTL_CCGR1]
str r4, [r0, #CLKCTL_CCGR2]
str r4, [r0, #CLKCTL_CCGR3]
ldr r1, =0x00030000
str r1, [r0, #CLKCTL_CCGR4]
ldr r1, =0x00FFF030
str r1, [r0, #CLKCTL_CCGR5]
ldr r1, =0x00000300
str r1, [r0, #CLKCTL_CCGR6]
/* Disable IPU and HSC dividers */
mov r1, #0x60000
str r1, [r0, #CLKCTL_CCDR]
/* Make sure to switch the DDR away from PLL 1 */
ldr r1, =0x19239145
str r1, [r0, #CLKCTL_CBCDR]
/* make sure divider effective */
1: ldr r1, [r0, #CLKCTL_CDHIPR]
cmp r1, #0x0
bne 1b
/* Switch ARM to step clock */
mov r1, #0x4
str r1, [r0, #CLKCTL_CCSR]
#if defined(CONFIG_MX51_PLL_ERRATA)
setup_pll PLL1_BASE_ADDR, 864
setup_pll_errata PLL1_BASE_ADDR, W_DP_MFN_800_DIT
#else
setup_pll PLL1_BASE_ADDR, 800
#endif
setup_pll PLL3_BASE_ADDR, 665
/* Switch peripheral to PLL 3 */
ldr r0, =CCM_BASE_ADDR
ldr r1, =0x000010C0 | CONFIG_SYS_DDR_CLKSEL
str r1, [r0, #CLKCTL_CBCMR]
ldr r1, =0x13239145
str r1, [r0, #CLKCTL_CBCDR]
setup_pll PLL2_BASE_ADDR, 665
/* Switch peripheral to PLL2 */
ldr r0, =CCM_BASE_ADDR
ldr r1, =0x19239145
str r1, [r0, #CLKCTL_CBCDR]
ldr r1, =0x000020C0 | CONFIG_SYS_DDR_CLKSEL
str r1, [r0, #CLKCTL_CBCMR]
setup_pll PLL3_BASE_ADDR, 216
/* Set the platform clock dividers */
ldr r0, =ARM_BASE_ADDR
ldr r1, =0x00000725
str r1, [r0, #0x14]
ldr r0, =CCM_BASE_ADDR
/* Run 3.0 at Full speed, for other TO's wait till we increase VDDGP */
ldr r3, [r4, #ROM_SI_REV]
cmp r3, #0x10
movls r1, #0x1
movhi r1, #0
str r1, [r0, #CLKCTL_CACRR]
/* Switch ARM back to PLL 1 */
str r4, [r0, #CLKCTL_CCSR]
/* setup the rest */
/* Use lp_apm (24MHz) source for perclk */
ldr r1, =0x000020C2 | CONFIG_SYS_DDR_CLKSEL
str r1, [r0, #CLKCTL_CBCMR]
/* ddr clock from PLL 1, all perclk dividers are 1 since using 24MHz */
ldr r1, =CONFIG_SYS_CLKTL_CBCDR
str r1, [r0, #CLKCTL_CBCDR]
/* Restore the default values in the Gate registers */
ldr r1, =0xFFFFFFFF
str r1, [r0, #CLKCTL_CCGR0]
str r1, [r0, #CLKCTL_CCGR1]
str r1, [r0, #CLKCTL_CCGR2]
str r1, [r0, #CLKCTL_CCGR3]
str r1, [r0, #CLKCTL_CCGR4]
str r1, [r0, #CLKCTL_CCGR5]
str r1, [r0, #CLKCTL_CCGR6]
/* Use PLL 2 for UART's, get 66.5MHz from it */
ldr r1, =0xA5A2A020
str r1, [r0, #CLKCTL_CSCMR1]
ldr r1, =0x00C30321
str r1, [r0, #CLKCTL_CSCDR1]
/* make sure divider effective */
1: ldr r1, [r0, #CLKCTL_CDHIPR]
cmp r1, #0x0
bne 1b
str r4, [r0, #CLKCTL_CCDR]
/* for cko - for ARM div by 8 */
mov r1, #0x000A0000
add r1, r1, #0x00000F0
str r1, [r0, #CLKCTL_CCOSR]
#else /* CONFIG_MX53 */
ldr r0, =CCM_BASE_ADDR
/* Gate of clocks to the peripherals first */
ldr r1, =0x3FFFFFFF
str r1, [r0, #CLKCTL_CCGR0]
str r4, [r0, #CLKCTL_CCGR1]
str r4, [r0, #CLKCTL_CCGR2]
str r4, [r0, #CLKCTL_CCGR3]
str r4, [r0, #CLKCTL_CCGR7]
ldr r1, =0x00030000
str r1, [r0, #CLKCTL_CCGR4]
ldr r1, =0x00FFF030
str r1, [r0, #CLKCTL_CCGR5]
ldr r1, =0x0F00030F
str r1, [r0, #CLKCTL_CCGR6]
/* Switch ARM to step clock */
mov r1, #0x4
str r1, [r0, #CLKCTL_CCSR]
setup_pll PLL1_BASE_ADDR, 800
setup_pll PLL3_BASE_ADDR, 400
/* Switch peripheral to PLL3 */
ldr r0, =CCM_BASE_ADDR
ldr r1, =0x00015154
str r1, [r0, #CLKCTL_CBCMR]
ldr r1, =0x02898945
str r1, [r0, #CLKCTL_CBCDR]
/* make sure change is effective */
1: ldr r1, [r0, #CLKCTL_CDHIPR]
cmp r1, #0x0
bne 1b
setup_pll PLL2_BASE_ADDR, 400
/* Switch peripheral to PLL2 */
ldr r0, =CCM_BASE_ADDR
ldr r1, =0x00888945
str r1, [r0, #CLKCTL_CBCDR]
ldr r1, =0x00016154
str r1, [r0, #CLKCTL_CBCMR]
/*change uart clk parent to pll2*/
ldr r1, [r0, #CLKCTL_CSCMR1]
and r1, r1, #0xfcffffff
orr r1, r1, #0x01000000
str r1, [r0, #CLKCTL_CSCMR1]
/* make sure change is effective */
1: ldr r1, [r0, #CLKCTL_CDHIPR]
cmp r1, #0x0
bne 1b
setup_pll PLL3_BASE_ADDR, 216
setup_pll PLL4_BASE_ADDR, 455
/* Set the platform clock dividers */
ldr r0, =ARM_BASE_ADDR
ldr r1, =0x00000124
str r1, [r0, #0x14]
ldr r0, =CCM_BASE_ADDR
mov r1, #0
str r1, [r0, #CLKCTL_CACRR]
/* Switch ARM back to PLL 1. */
mov r1, #0x0
str r1, [r0, #CLKCTL_CCSR]
/* make uart div=6 */
ldr r1, [r0, #CLKCTL_CSCDR1]
and r1, r1, #0xffffffc0
orr r1, r1, #0x0a
str r1, [r0, #CLKCTL_CSCDR1]
/* Restore the default values in the Gate registers */
ldr r1, =0xFFFFFFFF
str r1, [r0, #CLKCTL_CCGR0]
str r1, [r0, #CLKCTL_CCGR1]
str r1, [r0, #CLKCTL_CCGR2]
str r1, [r0, #CLKCTL_CCGR3]
str r1, [r0, #CLKCTL_CCGR4]
str r1, [r0, #CLKCTL_CCGR5]
str r1, [r0, #CLKCTL_CCGR6]
str r1, [r0, #CLKCTL_CCGR7]
mov r1, #0x00000
str r1, [r0, #CLKCTL_CCDR]
/* for cko - for ARM div by 8 */
mov r1, #0x000A0000
add r1, r1, #0x00000F0
str r1, [r0, #CLKCTL_CCOSR]
#endif /* CONFIG_MX53 */
.endm
ENTRY(lowlevel_init)
mov r10, lr
mov r4, #0 /* Fix R4 to 0 */
#if defined(CONFIG_SYS_MAIN_PWR_ON)
ldr r0, =GPIO1_BASE_ADDR
ldr r1, [r0, #0x0]
orr r1, r1, #1 << 23
str r1, [r0, #0x0]
ldr r1, [r0, #0x4]
orr r1, r1, #1 << 23
str r1, [r0, #0x4]
#endif
init_arm_erratum
init_l2cc
init_aips
init_m4if
init_clock
mov pc, r10
ENDPROC(lowlevel_init)
/* Board level setting value */
#if defined(CONFIG_MX51_PLL_ERRATA)
W_DP_864: .word DP_OP_864
.word DP_MFD_864
.word DP_MFN_864
W_DP_MFN_800_DIT: .word DP_MFN_800_DIT
#else
W_DP_800: .word DP_OP_800
.word DP_MFD_800
.word DP_MFN_800
#endif
#if defined(CONFIG_MX51)
W_DP_665: .word DP_OP_665
.word DP_MFD_665
.word DP_MFN_665
#endif
W_DP_216: .word DP_OP_216
.word DP_MFD_216
.word DP_MFN_216
W_DP_400: .word DP_OP_400
.word DP_MFD_400
.word DP_MFN_400
W_DP_455: .word DP_OP_455
.word DP_MFD_455
.word DP_MFN_455