| config BF52x | |
| def_bool y | |
| depends on (BF522 || BF523 || BF524 || BF525 || BF526 || BF527) | |
| if (BF52x) | |
| source "arch/blackfin/mach-bf527/boards/Kconfig" | |
| menu "BF527 Specific Configuration" | |
| comment "Alternative Multiplexing Scheme" | |
| choice | |
| prompt "SPORT0" | |
| default BF527_SPORT0_PORTG | |
| help | |
| Select PORT used for SPORT0. See Hardware Reference Manual | |
| config BF527_SPORT0_PORTF | |
| bool "PORT F" | |
| help | |
| PORT F | |
| config BF527_SPORT0_PORTG | |
| bool "PORT G" | |
| help | |
| PORT G | |
| endchoice | |
| choice | |
| prompt "SPORT0 TSCLK Location" | |
| depends on BF527_SPORT0_PORTG | |
| default BF527_SPORT0_TSCLK_PG10 | |
| help | |
| Select PIN used for SPORT0_TSCLK. See Hardware Reference Manual | |
| config BF527_SPORT0_TSCLK_PG10 | |
| bool "PORT PG10" | |
| help | |
| PORT PG10 | |
| config BF527_SPORT0_TSCLK_PG14 | |
| bool "PORT PG14" | |
| help | |
| PORT PG14 | |
| endchoice | |
| choice | |
| prompt "UART1" | |
| default BF527_UART1_PORTF | |
| help | |
| Select PORT used for UART1. See Hardware Reference Manual | |
| config BF527_UART1_PORTF | |
| bool "PORT F" | |
| help | |
| PORT F | |
| config BF527_UART1_PORTG | |
| bool "PORT G" | |
| help | |
| PORT G | |
| endchoice | |
| choice | |
| prompt "NAND (NFC) Data" | |
| default BF527_NAND_D_PORTH | |
| help | |
| Select PORT used for NAND Data Bus. See Hardware Reference Manual | |
| config BF527_NAND_D_PORTF | |
| bool "PORT F" | |
| help | |
| PORT F | |
| config BF527_NAND_D_PORTH | |
| bool "PORT H" | |
| help | |
| PORT H | |
| endchoice | |
| comment "Hysteresis/Schmitt Trigger Control" | |
| config BFIN_HYSTERESIS_CONTROL | |
| bool "Enable Hysteresis Control" | |
| help | |
| The ADSP-BF52x allows to control input hysteresis for Port F, | |
| Port G and Port H and other processor signal inputs. | |
| The Schmitt trigger enables can be set only for pin groups. | |
| Saying Y will overwrite the default reset or boot loader | |
| initialization. | |
| menu "PORT F" | |
| depends on BFIN_HYSTERESIS_CONTROL | |
| config GPIO_HYST_PORTF_0_7 | |
| bool "Enable Hysteresis on PORTF {0...7}" | |
| config GPIO_HYST_PORTF_8_9 | |
| bool "Enable Hysteresis on PORTF {8, 9}" | |
| config GPIO_HYST_PORTF_10 | |
| bool "Enable Hysteresis on PORTF 10" | |
| config GPIO_HYST_PORTF_11 | |
| bool "Enable Hysteresis on PORTF 11" | |
| config GPIO_HYST_PORTF_12_13 | |
| bool "Enable Hysteresis on PORTF {12, 13}" | |
| config GPIO_HYST_PORTF_14_15 | |
| bool "Enable Hysteresis on PORTF {14, 15}" | |
| endmenu | |
| menu "PORT G" | |
| depends on BFIN_HYSTERESIS_CONTROL | |
| config GPIO_HYST_PORTG_0 | |
| bool "Enable Hysteresis on PORTG 0" | |
| config GPIO_HYST_PORTG_1_4 | |
| bool "Enable Hysteresis on PORTG {1...4}" | |
| config GPIO_HYST_PORTG_5_6 | |
| bool "Enable Hysteresis on PORTG {5, 6}" | |
| config GPIO_HYST_PORTG_7_8 | |
| bool "Enable Hysteresis on PORTG {7, 8}" | |
| config GPIO_HYST_PORTG_9 | |
| bool "Enable Hysteresis on PORTG 9" | |
| config GPIO_HYST_PORTG_10 | |
| bool "Enable Hysteresis on PORTG 10" | |
| config GPIO_HYST_PORTG_11_13 | |
| bool "Enable Hysteresis on PORTG {11...13}" | |
| config GPIO_HYST_PORTG_14_15 | |
| bool "Enable Hysteresis on PORTG {14, 15}" | |
| endmenu | |
| menu "PORT H" | |
| depends on BFIN_HYSTERESIS_CONTROL | |
| config GPIO_HYST_PORTH_0_7 | |
| bool "Enable Hysteresis on PORTH {0...7}" | |
| config GPIO_HYST_PORTH_8 | |
| bool "Enable Hysteresis on PORTH 8" | |
| config GPIO_HYST_PORTH_9_15 | |
| bool "Enable Hysteresis on PORTH {9...15}" | |
| endmenu | |
| menu "None-GPIO" | |
| depends on BFIN_HYSTERESIS_CONTROL | |
| config NONEGPIO_HYST_TMR0_FS1_PPICLK | |
| bool "Enable Hysteresis on {TMR0, PPI_FS1, PPI_CLK}" | |
| config NONEGPIO_HYST_NMI_RST_BMODE | |
| bool "Enable Hysteresis on {NMI, RESET, BMODE}" | |
| config NONEGPIO_HYST_JTAG | |
| bool "Enable Hysteresis on JTAG" | |
| endmenu | |
| comment "Interrupt Priority Assignment" | |
| menu "Priority" | |
| config IRQ_PLL_WAKEUP | |
| int "IRQ_PLL_WAKEUP" | |
| default 7 | |
| config IRQ_DMA0_ERROR | |
| int "IRQ_DMA0_ERROR" | |
| default 7 | |
| config IRQ_DMAR0_BLK | |
| int "IRQ_DMAR0_BLK" | |
| default 7 | |
| config IRQ_DMAR1_BLK | |
| int "IRQ_DMAR1_BLK" | |
| default 7 | |
| config IRQ_DMAR0_OVR | |
| int "IRQ_DMAR0_OVR" | |
| default 7 | |
| config IRQ_DMAR1_OVR | |
| int "IRQ_DMAR1_OVR" | |
| default 7 | |
| config IRQ_PPI_ERROR | |
| int "IRQ_PPI_ERROR" | |
| default 7 | |
| config IRQ_MAC_ERROR | |
| int "IRQ_MAC_ERROR" | |
| default 7 | |
| config IRQ_SPORT0_ERROR | |
| int "IRQ_SPORT0_ERROR" | |
| default 7 | |
| config IRQ_SPORT1_ERROR | |
| int "IRQ_SPORT1_ERROR" | |
| default 7 | |
| config IRQ_UART0_ERROR | |
| int "IRQ_UART0_ERROR" | |
| default 7 | |
| config IRQ_UART1_ERROR | |
| int "IRQ_UART1_ERROR" | |
| default 7 | |
| config IRQ_RTC | |
| int "IRQ_RTC" | |
| default 8 | |
| config IRQ_PPI | |
| int "IRQ_PPI" | |
| default 8 | |
| config IRQ_SPORT0_RX | |
| int "IRQ_SPORT0_RX" | |
| default 9 | |
| config IRQ_SPORT0_TX | |
| int "IRQ_SPORT0_TX" | |
| default 9 | |
| config IRQ_SPORT1_RX | |
| int "IRQ_SPORT1_RX" | |
| default 9 | |
| config IRQ_SPORT1_TX | |
| int "IRQ_SPORT1_TX" | |
| default 9 | |
| config IRQ_TWI | |
| int "IRQ_TWI" | |
| default 10 | |
| config IRQ_SPI | |
| int "IRQ_SPI" | |
| default 10 | |
| config IRQ_UART0_RX | |
| int "IRQ_UART0_RX" | |
| default 10 | |
| config IRQ_UART0_TX | |
| int "IRQ_UART0_TX" | |
| default 10 | |
| config IRQ_UART1_RX | |
| int "IRQ_UART1_RX" | |
| default 10 | |
| config IRQ_UART1_TX | |
| int "IRQ_UART1_TX" | |
| default 10 | |
| config IRQ_OPTSEC | |
| int "IRQ_OPTSEC" | |
| default 11 | |
| config IRQ_CNT | |
| int "IRQ_CNT" | |
| default 11 | |
| config IRQ_MAC_RX | |
| int "IRQ_MAC_RX" | |
| default 11 | |
| config IRQ_PORTH_INTA | |
| int "IRQ_PORTH_INTA" | |
| default 11 | |
| config IRQ_MAC_TX | |
| int "IRQ_MAC_TX/NFC" | |
| default 11 | |
| config IRQ_PORTH_INTB | |
| int "IRQ_PORTH_INTB" | |
| default 11 | |
| config IRQ_TIMER0 | |
| int "IRQ_TIMER0" | |
| default 7 if TICKSOURCE_GPTMR0 | |
| default 8 | |
| config IRQ_TIMER1 | |
| int "IRQ_TIMER1" | |
| default 12 | |
| config IRQ_TIMER2 | |
| int "IRQ_TIMER2" | |
| default 12 | |
| config IRQ_TIMER3 | |
| int "IRQ_TIMER3" | |
| default 12 | |
| config IRQ_TIMER4 | |
| int "IRQ_TIMER4" | |
| default 12 | |
| config IRQ_TIMER5 | |
| int "IRQ_TIMER5" | |
| default 12 | |
| config IRQ_TIMER6 | |
| int "IRQ_TIMER6" | |
| default 12 | |
| config IRQ_TIMER7 | |
| int "IRQ_TIMER7" | |
| default 12 | |
| config IRQ_PORTG_INTA | |
| int "IRQ_PORTG_INTA" | |
| default 12 | |
| config IRQ_PORTG_INTB | |
| int "IRQ_PORTG_INTB" | |
| default 12 | |
| config IRQ_MEM_DMA0 | |
| int "IRQ_MEM_DMA0" | |
| default 13 | |
| config IRQ_MEM_DMA1 | |
| int "IRQ_MEM_DMA1" | |
| default 13 | |
| config IRQ_WATCH | |
| int "IRQ_WATCH" | |
| default 13 | |
| config IRQ_PORTF_INTA | |
| int "IRQ_PORTF_INTA" | |
| default 13 | |
| config IRQ_PORTF_INTB | |
| int "IRQ_PORTF_INTB" | |
| default 13 | |
| config IRQ_SPI_ERROR | |
| int "IRQ_SPI_ERROR" | |
| default 7 | |
| config IRQ_NFC_ERROR | |
| int "IRQ_NFC_ERROR" | |
| default 7 | |
| config IRQ_HDMA_ERROR | |
| int "IRQ_HDMA_ERROR" | |
| default 7 | |
| config IRQ_HDMA | |
| int "IRQ_HDMA" | |
| default 7 | |
| config IRQ_USB_EINT | |
| int "IRQ_USB_EINT" | |
| default 10 | |
| config IRQ_USB_INT0 | |
| int "IRQ_USB_INT0" | |
| default 10 | |
| config IRQ_USB_INT1 | |
| int "IRQ_USB_INT1" | |
| default 10 | |
| config IRQ_USB_INT2 | |
| int "IRQ_USB_INT2" | |
| default 10 | |
| config IRQ_USB_DMA | |
| int "IRQ_USB_DMA" | |
| default 10 | |
| help | |
| Enter the priority numbers between 7-13 ONLY. Others are Reserved. | |
| This applies to all the above. It is not recommended to assign the | |
| highest priority number 7 to UART or any other device. | |
| endmenu | |
| endmenu | |
| endif |