| config BF52x |
| def_bool y |
| depends on (BF522 || BF523 || BF524 || BF525 || BF526 || BF527) |
| |
| if (BF52x) |
| |
| source "arch/blackfin/mach-bf527/boards/Kconfig" |
| |
| menu "BF527 Specific Configuration" |
| |
| comment "Alternative Multiplexing Scheme" |
| |
| choice |
| prompt "SPORT0" |
| default BF527_SPORT0_PORTG |
| help |
| Select PORT used for SPORT0. See Hardware Reference Manual |
| |
| config BF527_SPORT0_PORTF |
| bool "PORT F" |
| help |
| PORT F |
| |
| config BF527_SPORT0_PORTG |
| bool "PORT G" |
| help |
| PORT G |
| endchoice |
| |
| choice |
| prompt "SPORT0 TSCLK Location" |
| depends on BF527_SPORT0_PORTG |
| default BF527_SPORT0_TSCLK_PG10 |
| help |
| Select PIN used for SPORT0_TSCLK. See Hardware Reference Manual |
| |
| config BF527_SPORT0_TSCLK_PG10 |
| bool "PORT PG10" |
| help |
| PORT PG10 |
| |
| config BF527_SPORT0_TSCLK_PG14 |
| bool "PORT PG14" |
| help |
| PORT PG14 |
| endchoice |
| |
| choice |
| prompt "UART1" |
| default BF527_UART1_PORTF |
| help |
| Select PORT used for UART1. See Hardware Reference Manual |
| |
| config BF527_UART1_PORTF |
| bool "PORT F" |
| help |
| PORT F |
| |
| config BF527_UART1_PORTG |
| bool "PORT G" |
| help |
| PORT G |
| endchoice |
| |
| choice |
| prompt "NAND (NFC) Data" |
| default BF527_NAND_D_PORTH |
| help |
| Select PORT used for NAND Data Bus. See Hardware Reference Manual |
| |
| config BF527_NAND_D_PORTF |
| bool "PORT F" |
| help |
| PORT F |
| |
| config BF527_NAND_D_PORTH |
| bool "PORT H" |
| help |
| PORT H |
| endchoice |
| |
| comment "Hysteresis/Schmitt Trigger Control" |
| config BFIN_HYSTERESIS_CONTROL |
| bool "Enable Hysteresis Control" |
| help |
| The ADSP-BF52x allows to control input hysteresis for Port F, |
| Port G and Port H and other processor signal inputs. |
| The Schmitt trigger enables can be set only for pin groups. |
| Saying Y will overwrite the default reset or boot loader |
| initialization. |
| |
| menu "PORT F" |
| depends on BFIN_HYSTERESIS_CONTROL |
| config GPIO_HYST_PORTF_0_7 |
| bool "Enable Hysteresis on PORTF {0...7}" |
| config GPIO_HYST_PORTF_8_9 |
| bool "Enable Hysteresis on PORTF {8, 9}" |
| config GPIO_HYST_PORTF_10 |
| bool "Enable Hysteresis on PORTF 10" |
| config GPIO_HYST_PORTF_11 |
| bool "Enable Hysteresis on PORTF 11" |
| config GPIO_HYST_PORTF_12_13 |
| bool "Enable Hysteresis on PORTF {12, 13}" |
| config GPIO_HYST_PORTF_14_15 |
| bool "Enable Hysteresis on PORTF {14, 15}" |
| endmenu |
| |
| menu "PORT G" |
| depends on BFIN_HYSTERESIS_CONTROL |
| config GPIO_HYST_PORTG_0 |
| bool "Enable Hysteresis on PORTG 0" |
| config GPIO_HYST_PORTG_1_4 |
| bool "Enable Hysteresis on PORTG {1...4}" |
| config GPIO_HYST_PORTG_5_6 |
| bool "Enable Hysteresis on PORTG {5, 6}" |
| config GPIO_HYST_PORTG_7_8 |
| bool "Enable Hysteresis on PORTG {7, 8}" |
| config GPIO_HYST_PORTG_9 |
| bool "Enable Hysteresis on PORTG 9" |
| config GPIO_HYST_PORTG_10 |
| bool "Enable Hysteresis on PORTG 10" |
| config GPIO_HYST_PORTG_11_13 |
| bool "Enable Hysteresis on PORTG {11...13}" |
| config GPIO_HYST_PORTG_14_15 |
| bool "Enable Hysteresis on PORTG {14, 15}" |
| endmenu |
| |
| menu "PORT H" |
| depends on BFIN_HYSTERESIS_CONTROL |
| config GPIO_HYST_PORTH_0_7 |
| bool "Enable Hysteresis on PORTH {0...7}" |
| config GPIO_HYST_PORTH_8 |
| bool "Enable Hysteresis on PORTH 8" |
| config GPIO_HYST_PORTH_9_15 |
| bool "Enable Hysteresis on PORTH {9...15}" |
| endmenu |
| |
| menu "None-GPIO" |
| depends on BFIN_HYSTERESIS_CONTROL |
| config NONEGPIO_HYST_TMR0_FS1_PPICLK |
| bool "Enable Hysteresis on {TMR0, PPI_FS1, PPI_CLK}" |
| config NONEGPIO_HYST_NMI_RST_BMODE |
| bool "Enable Hysteresis on {NMI, RESET, BMODE}" |
| config NONEGPIO_HYST_JTAG |
| bool "Enable Hysteresis on JTAG" |
| endmenu |
| |
| comment "Interrupt Priority Assignment" |
| menu "Priority" |
| |
| config IRQ_PLL_WAKEUP |
| int "IRQ_PLL_WAKEUP" |
| default 7 |
| config IRQ_DMA0_ERROR |
| int "IRQ_DMA0_ERROR" |
| default 7 |
| config IRQ_DMAR0_BLK |
| int "IRQ_DMAR0_BLK" |
| default 7 |
| config IRQ_DMAR1_BLK |
| int "IRQ_DMAR1_BLK" |
| default 7 |
| config IRQ_DMAR0_OVR |
| int "IRQ_DMAR0_OVR" |
| default 7 |
| config IRQ_DMAR1_OVR |
| int "IRQ_DMAR1_OVR" |
| default 7 |
| config IRQ_PPI_ERROR |
| int "IRQ_PPI_ERROR" |
| default 7 |
| config IRQ_MAC_ERROR |
| int "IRQ_MAC_ERROR" |
| default 7 |
| config IRQ_SPORT0_ERROR |
| int "IRQ_SPORT0_ERROR" |
| default 7 |
| config IRQ_SPORT1_ERROR |
| int "IRQ_SPORT1_ERROR" |
| default 7 |
| config IRQ_UART0_ERROR |
| int "IRQ_UART0_ERROR" |
| default 7 |
| config IRQ_UART1_ERROR |
| int "IRQ_UART1_ERROR" |
| default 7 |
| config IRQ_RTC |
| int "IRQ_RTC" |
| default 8 |
| config IRQ_PPI |
| int "IRQ_PPI" |
| default 8 |
| config IRQ_SPORT0_RX |
| int "IRQ_SPORT0_RX" |
| default 9 |
| config IRQ_SPORT0_TX |
| int "IRQ_SPORT0_TX" |
| default 9 |
| config IRQ_SPORT1_RX |
| int "IRQ_SPORT1_RX" |
| default 9 |
| config IRQ_SPORT1_TX |
| int "IRQ_SPORT1_TX" |
| default 9 |
| config IRQ_TWI |
| int "IRQ_TWI" |
| default 10 |
| config IRQ_SPI |
| int "IRQ_SPI" |
| default 10 |
| config IRQ_UART0_RX |
| int "IRQ_UART0_RX" |
| default 10 |
| config IRQ_UART0_TX |
| int "IRQ_UART0_TX" |
| default 10 |
| config IRQ_UART1_RX |
| int "IRQ_UART1_RX" |
| default 10 |
| config IRQ_UART1_TX |
| int "IRQ_UART1_TX" |
| default 10 |
| config IRQ_OPTSEC |
| int "IRQ_OPTSEC" |
| default 11 |
| config IRQ_CNT |
| int "IRQ_CNT" |
| default 11 |
| config IRQ_MAC_RX |
| int "IRQ_MAC_RX" |
| default 11 |
| config IRQ_PORTH_INTA |
| int "IRQ_PORTH_INTA" |
| default 11 |
| config IRQ_MAC_TX |
| int "IRQ_MAC_TX/NFC" |
| default 11 |
| config IRQ_PORTH_INTB |
| int "IRQ_PORTH_INTB" |
| default 11 |
| config IRQ_TIMER0 |
| int "IRQ_TIMER0" |
| default 7 if TICKSOURCE_GPTMR0 |
| default 8 |
| config IRQ_TIMER1 |
| int "IRQ_TIMER1" |
| default 12 |
| config IRQ_TIMER2 |
| int "IRQ_TIMER2" |
| default 12 |
| config IRQ_TIMER3 |
| int "IRQ_TIMER3" |
| default 12 |
| config IRQ_TIMER4 |
| int "IRQ_TIMER4" |
| default 12 |
| config IRQ_TIMER5 |
| int "IRQ_TIMER5" |
| default 12 |
| config IRQ_TIMER6 |
| int "IRQ_TIMER6" |
| default 12 |
| config IRQ_TIMER7 |
| int "IRQ_TIMER7" |
| default 12 |
| config IRQ_PORTG_INTA |
| int "IRQ_PORTG_INTA" |
| default 12 |
| config IRQ_PORTG_INTB |
| int "IRQ_PORTG_INTB" |
| default 12 |
| config IRQ_MEM_DMA0 |
| int "IRQ_MEM_DMA0" |
| default 13 |
| config IRQ_MEM_DMA1 |
| int "IRQ_MEM_DMA1" |
| default 13 |
| config IRQ_WATCH |
| int "IRQ_WATCH" |
| default 13 |
| config IRQ_PORTF_INTA |
| int "IRQ_PORTF_INTA" |
| default 13 |
| config IRQ_PORTF_INTB |
| int "IRQ_PORTF_INTB" |
| default 13 |
| config IRQ_SPI_ERROR |
| int "IRQ_SPI_ERROR" |
| default 7 |
| config IRQ_NFC_ERROR |
| int "IRQ_NFC_ERROR" |
| default 7 |
| config IRQ_HDMA_ERROR |
| int "IRQ_HDMA_ERROR" |
| default 7 |
| config IRQ_HDMA |
| int "IRQ_HDMA" |
| default 7 |
| config IRQ_USB_EINT |
| int "IRQ_USB_EINT" |
| default 10 |
| config IRQ_USB_INT0 |
| int "IRQ_USB_INT0" |
| default 10 |
| config IRQ_USB_INT1 |
| int "IRQ_USB_INT1" |
| default 10 |
| config IRQ_USB_INT2 |
| int "IRQ_USB_INT2" |
| default 10 |
| config IRQ_USB_DMA |
| int "IRQ_USB_DMA" |
| default 10 |
| |
| help |
| Enter the priority numbers between 7-13 ONLY. Others are Reserved. |
| This applies to all the above. It is not recommended to assign the |
| highest priority number 7 to UART or any other device. |
| |
| endmenu |
| |
| endmenu |
| |
| endif |
