blob: 0d2361ebe3d739e85c9a59cfa4e9441f30c57177 [file] [log] [blame]
Qualcomm WCNSS Peripheral Image Loader
This document defines the binding for a component that loads and boots firmware
on the Qualcomm WCNSS core.
- compatible:
Usage: required
Value type: <string>
Definition: must be one of:
"qcom,riva-pil",
"qcom,pronto-v1-pil",
"qcom,pronto-v2-pil"
- reg:
Usage: required
Value type: <prop-encoded-array>
Definition: must specify the base address and size of the CCU, DXE and
PMU register blocks
- reg-names:
Usage: required
Value type: <stringlist>
Definition: must be "ccu", "dxe", "pmu"
- interrupts-extended:
Usage: required
Value type: <prop-encoded-array>
Definition: must list the watchdog and fatal IRQs and may specify the
ready, handover and stop-ack IRQs
- interrupt-names:
Usage: required
Value type: <stringlist>
Definition: should be "wdog", "fatal", optionally followed by "ready",
"handover", "stop-ack"
- vddmx-supply:
- vddcx-supply:
- vddpx-supply:
Usage: required
Value type: <phandle>
Definition: reference to the regulators to be held on behalf of the
booting of the WCNSS core
- qcom,smem-states:
Usage: optional
Value type: <prop-encoded-array>
Definition: reference to the SMEM state used to indicate to WCNSS that
it should shut down
- qcom,smem-state-names:
Usage: optional
Value type: <stringlist>
Definition: should be "stop"
- memory-region:
Usage: required
Value type: <prop-encoded-array>
Definition: reference to reserved-memory node for the remote processor
see ../reserved-memory/reserved-memory.txt
= SUBNODES
A single subnode of the WCNSS PIL describes the attached rf module and its
resource dependencies.
- compatible:
Usage: required
Value type: <string>
Definition: must be one of:
"qcom,wcn3620",
"qcom,wcn3660",
"qcom,wcn3680"
- clocks:
Usage: required
Value type: <prop-encoded-array>
Definition: should specify the xo clock and optionally the rf clock
- clock-names:
Usage: required
Value type: <stringlist>
Definition: should be "xo", optionally followed by "rf"
- vddxo-supply:
- vddrfa-supply:
- vddpa-supply:
- vdddig-supply:
Usage: required
Value type: <phandle>
Definition: reference to the regulators to be held on behalf of the
booting of the WCNSS core
= EXAMPLE
The following example describes the resources needed to boot control the WCNSS,
with attached WCN3680, as it is commonly found on MSM8974 boards.
pronto@fb204000 {
compatible = "qcom,pronto-v2-pil";
reg = <0xfb204000 0x2000>, <0xfb202000 0x1000>, <0xfb21b000 0x3000>;
reg-names = "ccu", "dxe", "pmu";
interrupts-extended = <&intc 0 149 1>,
<&wcnss_smp2p_slave 0 0>,
<&wcnss_smp2p_slave 1 0>,
<&wcnss_smp2p_slave 2 0>,
<&wcnss_smp2p_slave 3 0>;
interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
vddmx-supply = <&pm8841_s1>;
vddcx-supply = <&pm8841_s2>;
vddpx-supply = <&pm8941_s3>;
qcom,smem-states = <&wcnss_smp2p_out 0>;
qcom,smem-state-names = "stop";
memory-region = <&wcnss_region>;
pinctrl-names = "default";
pinctrl-0 = <&wcnss_pin_a>;
iris {
compatible = "qcom,wcn3680";
clocks = <&rpmcc RPM_CXO_CLK_SRC>, <&rpmcc RPM_CXO_A2>;
clock-names = "xo", "rf";
vddxo-supply = <&pm8941_l6>;
vddrfa-supply = <&pm8941_l11>;
vddpa-supply = <&pm8941_l19>;
vdddig-supply = <&pm8941_s3>;
};
};