| Motorola MPC85xxCDS boards |
| -------------------------- |
| |
| The CDS family of boards consists of a PCI backplane called the |
| "Arcadia", a PCI-form-factor carrier card that plugs into a PCI slot, |
| and a CPU daughter card that bolts onto the daughter card. |
| |
| Much of the content of the README.mpc85xxads for the 85xx ADS boards |
| applies to the 85xx CDS boards as well. In particular the toolchain, |
| the switch nomenclature, and the basis for the memory map. There are |
| some differences, though. |
| |
| |
| Building U-Boot |
| --------------- |
| |
| The Binutils in current ELDK toolchain will not support MPC85xx |
| chip. You need to use binutils-2.14.tar.bz2 (or newer) from |
| http://ftp.gnu.org/gnu/binutils. |
| |
| The 85xx CDS code base is known to compile using: |
| gcc (GCC) 3.2.2 20030217 (Yellow Dog Linux 3.0 3.2.2-2a) |
| |
| |
| Memory Map |
| ---------- |
| |
| The memory map for u-boot and linux has been extended w.r.t. the ADS |
| platform to allow for utilization of all 85xx CDS devices. The memory |
| map is setup for linux to operate properly. The linux source when |
| configured for MPC85xx CDS has been updated to reflect the new memory |
| map. |
| |
| The mapping is: |
| |
| 0x0000_0000 0x7fff_ffff DDR 2G |
| 0x8000_0000 0x9fff_ffff PCI1 MEM 512M |
| 0xa000_0000 0xbfff_ffff PCI2 MEM 512M |
| 0xe000_0000 0xe00f_ffff CCSR 1M |
| 0xe200_0000 0xe2ff_ffff PCI1 IO 16M |
| 0xe300_0000 0xe3ff_ffff PCI2 IO 16M |
| 0xf000_0000 0xf7ff_ffff SDRAM 128M |
| 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M |
| 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M |
| 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M |
| |
| (*) The system control registers (CADMUS) start at offset 0xfdb0_4000 |
| within the NVRAM/CADMUS region of memory. |
| |
| |
| Using Flash |
| ----------- |
| |
| The CDS board has two flash banks, each 8MB in size (2^23 = 0x00800000). |
| There is a switch which allows the boot-bank to be selected. The switch |
| settings for updating flash are given below. |
| |
| The u-boot commands for copying the boot-bank into the secondary bank are |
| as follows: |
| |
| erase ff780000 ff7fffff |
| cp.b fff80000 ff780000 80000 |
| |
| |
| U-boot/kermit commands for downloading an image, then copying |
| it into the secondary bank: |
| |
| loadb |
| [Drop to kermit: |
| ^\c |
| send <u-boot-bin-image> |
| c |
| ] |
| |
| erase ff780000 ff7fffff |
| cp.b $loadaddr ff780000 80000 |
| |
| |
| U-boot commands for downloading an image via tftp and flashing |
| it into the second bank: |
| |
| tftp 10000 <u-boot.bin.image> |
| erase ff780000 ff7fffff |
| cp.b 10000 ff780000 80000 |
| |
| |
| After copying the image into the second bank of flash, be sure to toggle |
| SW2[2] on the carrier card before resetting the board in order to set the |
| secondary bank as the boot-bank. |
| |
| |
| Carrier Board Switches |
| ---------------------- |
| |
| As a reminder, you should read the README.mpc85xxads too. |
| |
| Most switches on the carrier board should not be changed. The only |
| user-settable switches on the carrier board are used to configure |
| the flash banks and determining the PCI slot. |
| |
| The first two bits of SW2 control how flash is used on the board: |
| |
| 12345678 |
| -------- |
| SW2=00XXXXXX FLASH: Boot bank 1, bank 2 available. |
| 01XXXXXX FLASH: Boot bank 2, bank 1 available (swapped). |
| 10XXXXXX FLASH: Boot promjet, bank 1 available |
| 11XXXXXX FLASH: Boot promjet, bank 2 available |
| |
| The boot bank is always mapped to FF80_0000 and listed first by |
| the "flinfo" command. The secondary bank is always FF00_0000. |
| |
| When using PCI, linux needs to know to which slot the CDS carrier is |
| connected.. By convention, the user-specific bits of SW2 are used to |
| convey this information: |
| |
| 12345678 |
| -------- |
| SW2=xxxxxx00 PCI SLOT INFORM: The CDS carrier is in slot0 of the Arcadia |
| xxxxxx01 PCI SLOT INFORM: The CDS carrier is in slot1 of the Arcadia |
| xxxxxx10 PCI SLOT INFORM: The CDS carrier is in slot2 of the Arcadia |
| xxxxxx11 PCI SLOT INFORM: The CDS carrier is in slot3 of the Arcadia |
| |
| These are cleverly, er, clearly silkscreened as Slot 1 through 4, |
| respectively, on the Arcadia near the support posts. |
| |
| |
| The default setting of all switches on the carrier board is: |
| |
| 12345678 |
| -------- |
| SW1=01101100 |
| SW2=0x1111yy x=Flash bank, yy=PCI slot |
| SW3=11101111 |
| SW4=10001000 |
| |
| |
| 8555/41 CPU Card Switches |
| ------------------------- |
| |
| Most switches on the CPU Card should not be changed. However, the |
| frequency can be changed by setting SW3: |
| |
| 12345678 |
| -------- |
| SW3=XX00XXXX == CORE:CCB 2:1 |
| XX01XXXX == CORE:CCB 5:2 |
| XX10XXXX == CORE:CCB 3:1 |
| XX11XXXX == CORE:CCB 7:2 |
| XXXX1000 == CCB:SYSCLK 8:1 |
| XXXX1010 == CCB:SYSCLK 10:1 |
| |
| A safe default setting for all switches on the CPU board is: |
| |
| 12345678 |
| -------- |
| SW1=10001111 |
| SW2=01000111 |
| SW3=00001000 |
| SW4=11111110 |
| |
| |
| 8548 CPU Card Switches |
| ---------------------- |
| And, just to be confusing, in this set of switches: |
| |
| ON = 1 |
| OFF = 0 |
| |
| Default |
| SW1=11111101 |
| SW2=10011111 |
| SW3=11001000 (8X) (2:1) |
| SW4=11110011 |
| |
| SW3=X000XXXX == CORE:CCB 4:1 |
| X001XXXX == CORE:CCB 9:2 |
| X010XXXX == CORE:CCB 1:1 |
| X011XXXX == CORE:CCB 3:2 |
| X100XXXX == CORE:CCB 2:1 |
| X101XXXX == CORE:CCB 5:2 |
| X110XXXX == CORE:CCB 3:1 |
| X111XXXX == CORE:CCB 7:2 |
| XXXX0000 == CCB:SYSCLK 16:1 |
| XXXX0001 == RESERVED |
| XXXX0010 == CCB:SYSCLK 2:1 |
| XXXX0011 == CCB:SYSCLK 3:1 |
| XXXX0100 == CCB:SYSCLK 4:1 |
| XXXX0101 == CCB:SYSCLK 5:1 |
| XXXX0110 == CCB:SYSCLK 6:1 |
| XXXX0111 == RESERVED |
| XXXX1000 == CCB:SYSCLK 8:1 |
| XXXX1001 == CCB:SYSCLK 9:1 |
| XXXX1010 == CCB:SYSCLK 10:1 |
| XXXX1011 == RESERVED |
| XXXX1100 == CCB:SYSCLK 12:1 |
| XXXX1101 == CCB:SYSCLK 20:1 |
| XXXX1110 == RESERVED |
| XXXX1111 == RESERVED |
| |
| |
| eDINK Info |
| ---------- |
| |
| One bank of flash may contain an eDINK image. |
| |
| Memory Map: |
| |
| CCSRBAR @ 0xe0000000 |
| Flash Bank 1 @ 0xfe000000 |
| Flash Bank 2 @ 0xff000000 |
| Ram @ 0 |
| |
| Commands for downloading a u-boot image to memory from edink: |
| |
| env -c |
| time -s 4/8/2004 4:30p |
| dl -k -b -o 100000 |
| [Drop to kermit: |
| ^\c |
| transmit /binary <u-boot-bin-image> |
| c |
| ] |
| |
| fu -l 100000 fe780000 80000 |
