| /* | 
 |  * (C) Copyright 2001 | 
 |  * Denis Peter, MPL AG Switzerland, d.peter@mpl.ch. | 
 |  * | 
 |  * SPDX-License-Identifier:	GPL-2.0+ | 
 |  * partly derived from | 
 |  * linux/drivers/scsi/sym53c8xx.c | 
 |  * | 
 |  */ | 
 |  | 
 | /* | 
 |  * SCSI support based on the chip sym53C810. | 
 |  * | 
 |  * 09-19-2001 Andreas Heppel, Sysgo RTS GmbH <aheppel@sysgo.de> | 
 |  *		The local version of this driver for the BAB750 board does not | 
 |  *		use interrupts but polls the chip instead (see the call of | 
 |  *		'handle_scsi_int()' in 'scsi_issue()'. | 
 |  */ | 
 |  | 
 | #include <common.h> | 
 |  | 
 | #include <command.h> | 
 | #include <pci.h> | 
 | #include <asm/processor.h> | 
 | #include <sym53c8xx.h> | 
 | #include <scsi.h> | 
 |  | 
 | #undef	SYM53C8XX_DEBUG | 
 |  | 
 | #ifdef	SYM53C8XX_DEBUG | 
 | #define	PRINTF(fmt,args...)	printf (fmt ,##args) | 
 | #else | 
 | #define PRINTF(fmt,args...) | 
 | #endif | 
 |  | 
 | #if defined(CONFIG_CMD_SCSI) && defined(CONFIG_SCSI_SYM53C8XX) | 
 |  | 
 | #undef SCSI_SINGLE_STEP | 
 | /* | 
 |  * Single Step is only used for debug purposes | 
 |  */ | 
 | #ifdef SCSI_SINGLE_STEP | 
 | static unsigned long start_script_select; | 
 | static unsigned long start_script_msgout; | 
 | static unsigned long start_script_msgin; | 
 | static unsigned long start_script_msg_ext; | 
 | static unsigned long start_script_cmd; | 
 | static unsigned long start_script_data_in; | 
 | static unsigned long start_script_data_out; | 
 | static unsigned long start_script_status; | 
 | static unsigned long start_script_complete; | 
 | static unsigned long start_script_error; | 
 | static unsigned long start_script_reselection; | 
 | static unsigned int len_script_select; | 
 | static unsigned int len_script_msgout; | 
 | static unsigned int len_script_msgin; | 
 | static unsigned int len_script_msg_ext; | 
 | static unsigned int len_script_cmd; | 
 | static unsigned int len_script_data_in; | 
 | static unsigned int len_script_data_out; | 
 | static unsigned int len_script_status; | 
 | static unsigned int len_script_complete; | 
 | static unsigned int len_script_error; | 
 | static unsigned int len_script_reselection; | 
 | #endif | 
 |  | 
 |  | 
 | static unsigned short scsi_int_mask;	/* shadow register for SCSI related interrupts */ | 
 | static unsigned char  script_int_mask;	/* shadow register for SCRIPT related interrupts */ | 
 | static unsigned long script_select[8];	/* script for selection */ | 
 | static unsigned long script_msgout[8];	/* script for message out phase (NOT USED) */ | 
 | static unsigned long script_msgin[14];	/* script for message in phase */ | 
 | static unsigned long script_msg_ext[32]; /* script for message in phase when more than 1 byte message */ | 
 | static unsigned long script_cmd[18];    /* script for command phase */ | 
 | static unsigned long script_data_in[8]; /* script for data in phase */ | 
 | static unsigned long script_data_out[8]; /* script for data out phase */ | 
 | static unsigned long script_status[6]; /* script for status phase */ | 
 | static unsigned long script_complete[10]; /* script for complete */ | 
 | static unsigned long script_reselection[4]; /* script for reselection (NOT USED) */ | 
 | static unsigned long script_error[2]; /* script for error handling */ | 
 |  | 
 | static unsigned long int_stat[3]; /* interrupt status */ | 
 | static unsigned long scsi_mem_addr; /* base memory address =SCSI_MEM_ADDRESS; */ | 
 |  | 
 | #define bus_to_phys(a)	pci_mem_to_phys(busdevfunc, (unsigned long) (a)) | 
 | #define phys_to_bus(a)	pci_phys_to_mem(busdevfunc, (unsigned long) (a)) | 
 |  | 
 | #define SCSI_MAX_RETRY 3 /* number of retries in scsi_issue() */ | 
 |  | 
 | #define SCSI_MAX_RETRY_NOT_READY 10 /* number of retries when device is not ready */ | 
 | #define SCSI_NOT_READY_TIME_OUT 500 /* timeout per retry when not ready */ | 
 |  | 
 | /********************************************************************************* | 
 |  * forward declerations | 
 |  */ | 
 |  | 
 | void scsi_chip_init(void); | 
 | void handle_scsi_int(void); | 
 |  | 
 |  | 
 | /******************************************************************************** | 
 |  * reports SCSI errors to the user | 
 |  */ | 
 | void scsi_print_error (ccb * pccb) | 
 | { | 
 | 	int i; | 
 |  | 
 | 	printf ("SCSI Error: Target %d LUN %d Command %02X\n", pccb->target, | 
 | 		pccb->lun, pccb->cmd[0]); | 
 | 	printf ("       CCB: "); | 
 | 	for (i = 0; i < pccb->cmdlen; i++) | 
 | 		printf ("%02X ", pccb->cmd[i]); | 
 | 	printf ("(len=%d)\n", pccb->cmdlen); | 
 | 	printf ("     Cntrl: "); | 
 | 	switch (pccb->contr_stat) { | 
 | 	case SIR_COMPLETE: | 
 | 		printf ("Complete (no Error)\n"); | 
 | 		break; | 
 | 	case SIR_SEL_ATN_NO_MSG_OUT: | 
 | 		printf ("Selected with ATN no MSG out phase\n"); | 
 | 		break; | 
 | 	case SIR_CMD_OUT_ILL_PH: | 
 | 		printf ("Command out illegal phase\n"); | 
 | 		break; | 
 | 	case SIR_MSG_RECEIVED: | 
 | 		printf ("MSG received Error\n"); | 
 | 		break; | 
 | 	case SIR_DATA_IN_ERR: | 
 | 		printf ("Data in Error\n"); | 
 | 		break; | 
 | 	case SIR_DATA_OUT_ERR: | 
 | 		printf ("Data out Error\n"); | 
 | 		break; | 
 | 	case SIR_SCRIPT_ERROR: | 
 | 		printf ("Script Error\n"); | 
 | 		break; | 
 | 	case SIR_MSG_OUT_NO_CMD: | 
 | 		printf ("MSG out no Command phase\n"); | 
 | 		break; | 
 | 	case SIR_MSG_OVER7: | 
 | 		printf ("MSG in over 7 bytes\n"); | 
 | 		break; | 
 | 	case INT_ON_FY: | 
 | 		printf ("Interrupt on fly\n"); | 
 | 		break; | 
 | 	case SCSI_SEL_TIME_OUT: | 
 | 		printf ("SCSI Selection Timeout\n"); | 
 | 		break; | 
 | 	case SCSI_HNS_TIME_OUT: | 
 | 		printf ("SCSI Handshake Timeout\n"); | 
 | 		break; | 
 | 	case SCSI_MA_TIME_OUT: | 
 | 		printf ("SCSI Phase Error\n"); | 
 | 		break; | 
 | 	case SCSI_UNEXP_DIS: | 
 | 		printf ("SCSI unexpected disconnect\n"); | 
 | 		break; | 
 | 	default: | 
 | 		printf ("unknown status %lx\n", pccb->contr_stat); | 
 | 		break; | 
 | 	} | 
 | 	printf ("     Sense: SK %x (", pccb->sense_buf[2] & 0x0f); | 
 | 	switch (pccb->sense_buf[2] & 0xf) { | 
 | 	case SENSE_NO_SENSE: | 
 | 		printf ("No Sense)"); | 
 | 		break; | 
 | 	case SENSE_RECOVERED_ERROR: | 
 | 		printf ("Recovered Error)"); | 
 | 		break; | 
 | 	case SENSE_NOT_READY: | 
 | 		printf ("Not Ready)"); | 
 | 		break; | 
 | 	case SENSE_MEDIUM_ERROR: | 
 | 		printf ("Medium Error)"); | 
 | 		break; | 
 | 	case SENSE_HARDWARE_ERROR: | 
 | 		printf ("Hardware Error)"); | 
 | 		break; | 
 | 	case SENSE_ILLEGAL_REQUEST: | 
 | 		printf ("Illegal request)"); | 
 | 		break; | 
 | 	case SENSE_UNIT_ATTENTION: | 
 | 		printf ("Unit Attention)"); | 
 | 		break; | 
 | 	case SENSE_DATA_PROTECT: | 
 | 		printf ("Data Protect)"); | 
 | 		break; | 
 | 	case SENSE_BLANK_CHECK: | 
 | 		printf ("Blank check)"); | 
 | 		break; | 
 | 	case SENSE_VENDOR_SPECIFIC: | 
 | 		printf ("Vendor specific)"); | 
 | 		break; | 
 | 	case SENSE_COPY_ABORTED: | 
 | 		printf ("Copy aborted)"); | 
 | 		break; | 
 | 	case SENSE_ABORTED_COMMAND: | 
 | 		printf ("Aborted Command)"); | 
 | 		break; | 
 | 	case SENSE_VOLUME_OVERFLOW: | 
 | 		printf ("Volume overflow)"); | 
 | 		break; | 
 | 	case SENSE_MISCOMPARE: | 
 | 		printf ("Misscompare\n"); | 
 | 		break; | 
 | 	default: | 
 | 		printf ("Illegal Sensecode\n"); | 
 | 		break; | 
 | 	} | 
 | 	printf (" ASC %x ASCQ %x\n", pccb->sense_buf[12], | 
 | 		pccb->sense_buf[13]); | 
 | 	printf ("    Status: "); | 
 | 	switch (pccb->status) { | 
 | 	case S_GOOD: | 
 | 		printf ("Good\n"); | 
 | 		break; | 
 | 	case S_CHECK_COND: | 
 | 		printf ("Check condition\n"); | 
 | 		break; | 
 | 	case S_COND_MET: | 
 | 		printf ("Condition Met\n"); | 
 | 		break; | 
 | 	case S_BUSY: | 
 | 		printf ("Busy\n"); | 
 | 		break; | 
 | 	case S_INT: | 
 | 		printf ("Intermediate\n"); | 
 | 		break; | 
 | 	case S_INT_COND_MET: | 
 | 		printf ("Intermediate condition met\n"); | 
 | 		break; | 
 | 	case S_CONFLICT: | 
 | 		printf ("Reservation conflict\n"); | 
 | 		break; | 
 | 	case S_TERMINATED: | 
 | 		printf ("Command terminated\n"); | 
 | 		break; | 
 | 	case S_QUEUE_FULL: | 
 | 		printf ("Task set full\n"); | 
 | 		break; | 
 | 	default: | 
 | 		printf ("unknown: %02X\n", pccb->status); | 
 | 		break; | 
 | 	} | 
 |  | 
 | } | 
 |  | 
 |  | 
 | /****************************************************************************** | 
 |  * sets-up the SCSI controller | 
 |  * the base memory address is retrieved via the pci_read_config_dword | 
 |  */ | 
 | void scsi_low_level_init(int busdevfunc) | 
 | { | 
 | 	unsigned int cmd; | 
 | 	unsigned int addr; | 
 | 	unsigned char vec; | 
 |  | 
 | 	pci_read_config_byte(busdevfunc, PCI_INTERRUPT_LINE, &vec); | 
 | 	pci_read_config_dword(busdevfunc, PCI_BASE_ADDRESS_1, &addr); | 
 |  | 
 | 	addr = bus_to_phys(addr & ~0xf); | 
 |  | 
 | 	/* | 
 | 	 * Enable bus mastering in case this has not been done, yet. | 
 | 	 */ | 
 | 	pci_read_config_dword(busdevfunc, PCI_COMMAND, &cmd); | 
 | 	cmd |= PCI_COMMAND_MASTER; | 
 | 	pci_write_config_dword(busdevfunc, PCI_COMMAND, cmd); | 
 |  | 
 | 	scsi_mem_addr = addr; | 
 |  | 
 | 	scsi_chip_init(); | 
 | 	scsi_bus_reset(); | 
 | } | 
 |  | 
 |  | 
 | /************************************************************************************ | 
 |  * Low level Part of SCSI Driver | 
 |  */ | 
 |  | 
 | /* | 
 |  * big-endian -> little endian conversion for the script | 
 |  */ | 
 | unsigned long swap_script(unsigned long val) | 
 | { | 
 | 	unsigned long tmp; | 
 | 	tmp = ((val>>24)&0xff) | ((val>>8)&0xff00) | ((val<<8)&0xff0000) | ((val<<24)&0xff000000); | 
 | 	return tmp; | 
 | } | 
 |  | 
 |  | 
 | void scsi_write_byte(ulong offset,unsigned char val) | 
 | { | 
 | 	out8(scsi_mem_addr+offset,val); | 
 | } | 
 |  | 
 |  | 
 | unsigned char scsi_read_byte(ulong offset) | 
 | { | 
 | 	return(in8(scsi_mem_addr+offset)); | 
 | } | 
 |  | 
 |  | 
 | /******************************************************************************** | 
 |  * interrupt handler | 
 |  */ | 
 | void handle_scsi_int(void) | 
 | { | 
 | 	unsigned char stat,stat1,stat2; | 
 | 	unsigned short sstat; | 
 | 	int i; | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	unsigned long tt; | 
 | #endif | 
 | 	stat=scsi_read_byte(ISTAT); | 
 | 	if((stat & DIP)==DIP) { /* DMA Interrupt pending */ | 
 | 		stat1=scsi_read_byte(DSTAT); | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 		if((stat1 & SSI)==SSI) { | 
 | 			tt=in32r(scsi_mem_addr+DSP); | 
 | 			if(((tt)>=start_script_select) && ((tt)<start_script_select+len_script_select)) { | 
 | 				printf("select %d\n",(tt-start_script_select)>>2); | 
 | 				goto end_single; | 
 | 			} | 
 | 			if(((tt)>=start_script_msgout) && ((tt)<start_script_msgout+len_script_msgout)) { | 
 | 				printf("msgout %d\n",(tt-start_script_msgout)>>2); | 
 | 				goto end_single; | 
 | 			} | 
 | 			if(((tt)>=start_script_msgin) && ((tt)<start_script_msgin+len_script_msgin)) { | 
 | 				printf("msgin %d\n",(tt-start_script_msgin)>>2); | 
 | 				goto end_single; | 
 | 			} | 
 | 			if(((tt)>=start_script_msg_ext) && ((tt)<start_script_msg_ext+len_script_msg_ext)) { | 
 | 				printf("msgin_ext %d\n",(tt-start_script_msg_ext)>>2); | 
 | 				goto end_single; | 
 | 			} | 
 | 			if(((tt)>=start_script_cmd) && ((tt)<start_script_cmd+len_script_cmd)) { | 
 | 				printf("cmd %d\n",(tt-start_script_cmd)>>2); | 
 | 				goto end_single; | 
 | 			} | 
 | 			if(((tt)>=start_script_data_in) && ((tt)<start_script_data_in+len_script_data_in)) { | 
 | 				printf("data_in %d\n",(tt-start_script_data_in)>>2); | 
 | 				goto end_single; | 
 | 			} | 
 | 			if(((tt)>=start_script_data_out) && ((tt)<start_script_data_out+len_script_data_out)) { | 
 | 				printf("data_out %d\n",(tt-start_script_data_out)>>2); | 
 | 				goto end_single; | 
 | 			} | 
 | 			if(((tt)>=start_script_status) && ((tt)<start_script_status+len_script_status)) { | 
 | 				printf("status %d\n",(tt-start_script_status)>>2); | 
 | 				goto end_single; | 
 | 			} | 
 | 			if(((tt)>=start_script_complete) && ((tt)<start_script_complete+len_script_complete)) { | 
 | 				printf("complete %d\n",(tt-start_script_complete)>>2); | 
 | 				goto end_single; | 
 | 			} | 
 | 			if(((tt)>=start_script_error) && ((tt)<start_script_error+len_script_error)) { | 
 | 				printf("error %d\n",(tt-start_script_error)>>2); | 
 | 				goto end_single; | 
 | 			} | 
 | 			if(((tt)>=start_script_reselection) && ((tt)<start_script_reselection+len_script_reselection)) { | 
 | 				printf("reselection %d\n",(tt-start_script_reselection)>>2); | 
 | 				goto end_single; | 
 | 			} | 
 | 			printf("sc: %lx\n",tt); | 
 | end_single: | 
 | 			stat2=scsi_read_byte(DCNTL); | 
 | 			stat2|=STD; | 
 | 			scsi_write_byte(DCNTL,stat2); | 
 | 		} | 
 | #endif | 
 | 		if((stat1 & SIR)==SIR) /* script interrupt */ | 
 | 		{ | 
 | 			int_stat[0]=in32(scsi_mem_addr+DSPS); | 
 | 		} | 
 | 		if((stat1 & DFE)==0) { /* fifo not epmty */ | 
 | 			scsi_write_byte(CTEST3,CLF); /* Clear DMA FIFO */ | 
 | 			stat2=scsi_read_byte(STEST3); | 
 | 			scsi_write_byte(STEST3,(stat2 | CSF)); /* Clear SCSI FIFO */ | 
 | 		} | 
 | 	} | 
 | 	if((stat & SIP)==SIP) {  /* scsi interrupt */ | 
 | 		sstat = (unsigned short)scsi_read_byte(SIST+1); | 
 | 		sstat <<=8; | 
 | 		sstat |= (unsigned short)scsi_read_byte(SIST); | 
 | 		for(i=0;i<3;i++) { | 
 | 			if(int_stat[i]==0) | 
 | 				break; /* found an empty int status */ | 
 | 		} | 
 | 		int_stat[i]=SCSI_INT_STATE | sstat; | 
 | 		stat1=scsi_read_byte(DSTAT); | 
 | 		if((stat1 & DFE)==0) { /* fifo not epmty */ | 
 | 			scsi_write_byte(CTEST3,CLF); /* Clear DMA FIFO */ | 
 | 			stat2=scsi_read_byte(STEST3); | 
 | 			scsi_write_byte(STEST3,(stat2 | CSF)); /* Clear SCSI FIFO */ | 
 | 		} | 
 | 	} | 
 | 	if((stat & INTF)==INTF) { /* interrupt on Fly */ | 
 | 		scsi_write_byte(ISTAT,stat); /* clear it */ | 
 | 		for(i=0;i<3;i++) { | 
 | 			if(int_stat[i]==0) | 
 | 				break; /* found an empty int status */ | 
 | 		} | 
 | 		int_stat[i]=INT_ON_FY; | 
 | 	} | 
 | } | 
 |  | 
 | void scsi_bus_reset(void) | 
 | { | 
 | 	unsigned char t; | 
 | 	int i; | 
 | 	int end = CONFIG_SYS_SCSI_SPIN_UP_TIME*1000; | 
 |  | 
 | 	t=scsi_read_byte(SCNTL1); | 
 | 	scsi_write_byte(SCNTL1,(t | CRST)); | 
 | 	udelay(50); | 
 | 	scsi_write_byte(SCNTL1,t); | 
 |  | 
 | 	puts("waiting for devices to spin up"); | 
 | 	for(i=0;i<end;i++) { | 
 | 		udelay(1000); /* give the devices time to spin up */ | 
 | 		if (i % 1000 == 0) | 
 | 			putc('.'); | 
 | 	} | 
 | 	putc('\n'); | 
 | 	scsi_chip_init(); /* reinit the chip ...*/ | 
 |  | 
 | } | 
 |  | 
 | void scsi_int_enable(void) | 
 | { | 
 | 	scsi_write_byte(SIEN,(unsigned char)scsi_int_mask); | 
 | 	scsi_write_byte(SIEN+1,(unsigned char)(scsi_int_mask>>8)); | 
 | 	scsi_write_byte(DIEN,script_int_mask); | 
 | } | 
 |  | 
 | void scsi_write_dsp(unsigned long start) | 
 | { | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	unsigned char t; | 
 | #endif | 
 | 	out32r(scsi_mem_addr + DSP,start); | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	t=scsi_read_byte(DCNTL); | 
 |   t|=STD; | 
 | 	scsi_write_byte(DCNTL,t); | 
 | #endif | 
 | } | 
 |  | 
 | /* only used for debug purposes */ | 
 | void scsi_print_script(void) | 
 | { | 
 | 	printf("script_select @         0x%08lX\n",(unsigned long)&script_select[0]); | 
 | 	printf("script_msgout @         0x%08lX\n",(unsigned long)&script_msgout[0]); | 
 | 	printf("script_msgin @          0x%08lX\n",(unsigned long)&script_msgin[0]); | 
 | 	printf("script_msgext @         0x%08lX\n",(unsigned long)&script_msg_ext[0]); | 
 | 	printf("script_cmd @            0x%08lX\n",(unsigned long)&script_cmd[0]); | 
 | 	printf("script_data_in @        0x%08lX\n",(unsigned long)&script_data_in[0]); | 
 | 	printf("script_data_out @       0x%08lX\n",(unsigned long)&script_data_out[0]); | 
 | 	printf("script_status @         0x%08lX\n",(unsigned long)&script_status[0]); | 
 | 	printf("script_complete @       0x%08lX\n",(unsigned long)&script_complete[0]); | 
 | 	printf("script_error @          0x%08lX\n",(unsigned long)&script_error[0]); | 
 | } | 
 |  | 
 |  | 
 | void scsi_set_script(ccb *pccb) | 
 | { | 
 | 	int busdevfunc = pccb->priv; | 
 | 	int i; | 
 | 	i=0; | 
 | 	script_select[i++]=swap_script(SCR_REG_REG(GPREG, SCR_AND, 0xfe)); | 
 | 	script_select[i++]=0; /* LED ON */ | 
 | 	script_select[i++]=swap_script(SCR_CLR(SCR_TRG)); /* select initiator mode */ | 
 | 	script_select[i++]=0; | 
 | 	/* script_select[i++]=swap_script(SCR_SEL_ABS_ATN | pccb->target << 16); */ | 
 | 	script_select[i++]=swap_script(SCR_SEL_ABS | pccb->target << 16); | 
 | 	script_select[i++]=swap_script(phys_to_bus(&script_cmd[4])); /* error handling */ | 
 | 	script_select[i++]=swap_script(SCR_JUMP); /* next section */ | 
 | 	/*	script_select[i++]=swap_script((unsigned long)&script_msgout[0]); */ /* message out */ | 
 | 	script_select[i++]=swap_script(phys_to_bus(&script_cmd[0])); /* command out */ | 
 |  | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	start_script_select=(unsigned long)&script_select[0]; | 
 | 	len_script_select=i*4; | 
 | #endif | 
 |  | 
 | 	i=0; | 
 | 	script_msgout[i++]=swap_script(SCR_INT ^ IFFALSE (WHEN (SCR_MSG_OUT))); | 
 | 	script_msgout[i++]=SIR_SEL_ATN_NO_MSG_OUT; | 
 | 	script_msgout[i++]=swap_script(	SCR_MOVE_ABS(1) ^ SCR_MSG_OUT); | 
 | 	script_msgout[i++]=swap_script(phys_to_bus(&pccb->msgout[0])); | 
 | 	script_msgout[i++]=swap_script(SCR_JUMP ^ IFTRUE (WHEN (SCR_COMMAND))); /* if Command phase */ | 
 | 	script_msgout[i++]=swap_script(phys_to_bus(&script_cmd[0])); /* switch to command */ | 
 | 	script_msgout[i++]=swap_script(SCR_INT); /* interrupt if not */ | 
 | 	script_msgout[i++]=SIR_MSG_OUT_NO_CMD; | 
 |  | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	start_script_msgout=(unsigned long)&script_msgout[0]; | 
 | 	len_script_msgout=i*4; | 
 | #endif | 
 | 	i=0; | 
 | 	script_cmd[i++]=swap_script(SCR_MOVE_ABS(pccb->cmdlen) ^ SCR_COMMAND); | 
 | 	script_cmd[i++]=swap_script(phys_to_bus(&pccb->cmd[0])); | 
 | 	script_cmd[i++]=swap_script(SCR_JUMP ^ IFTRUE (WHEN (SCR_MSG_IN))); /* message in ? */ | 
 | 	script_cmd[i++]=swap_script(phys_to_bus(&script_msgin[0])); | 
 | 	script_cmd[i++]=swap_script(SCR_JUMP ^ IFTRUE (IF (SCR_DATA_OUT))); /* data out ? */ | 
 | 	script_cmd[i++]=swap_script(phys_to_bus(&script_data_out[0])); | 
 | 	script_cmd[i++]=swap_script(SCR_JUMP ^ IFTRUE (IF (SCR_DATA_IN))); /* data in ? */ | 
 | 	script_cmd[i++]=swap_script(phys_to_bus(&script_data_in[0])); | 
 | 	script_cmd[i++]=swap_script(SCR_JUMP ^ IFTRUE (IF (SCR_STATUS)));  /* status ? */ | 
 | 	script_cmd[i++]=swap_script(phys_to_bus(&script_status[0])); | 
 | 	script_cmd[i++]=swap_script(SCR_JUMP ^ IFTRUE (IF (SCR_COMMAND)));  /* command ? */ | 
 | 	script_cmd[i++]=swap_script(phys_to_bus(&script_cmd[0])); | 
 | 	script_cmd[i++]=swap_script(SCR_JUMP ^ IFTRUE (IF (SCR_MSG_OUT)));  /* message out ? */ | 
 | 	script_cmd[i++]=swap_script(phys_to_bus(&script_msgout[0])); | 
 | 	script_cmd[i++]=swap_script(SCR_JUMP ^ IFTRUE (IF (SCR_MSG_IN))); /* just for error handling message in ? */ | 
 | 	script_cmd[i++]=swap_script(phys_to_bus(&script_msgin[0])); | 
 | 	script_cmd[i++]=swap_script(SCR_INT); /* interrupt if not */ | 
 | 	script_cmd[i++]=SIR_CMD_OUT_ILL_PH; | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	start_script_cmd=(unsigned long)&script_cmd[0]; | 
 | 	len_script_cmd=i*4; | 
 | #endif | 
 | 	i=0; | 
 | 	script_data_out[i++]=swap_script(SCR_MOVE_ABS(pccb->datalen)^ SCR_DATA_OUT); /* move */ | 
 | 	script_data_out[i++]=swap_script(phys_to_bus(pccb->pdata)); /* pointer to buffer */ | 
 | 	script_data_out[i++]=swap_script(SCR_JUMP ^ IFTRUE (WHEN (SCR_STATUS))); | 
 | 	script_data_out[i++]=swap_script(phys_to_bus(&script_status[0])); | 
 | 	script_data_out[i++]=swap_script(SCR_INT); | 
 | 	script_data_out[i++]=SIR_DATA_OUT_ERR; | 
 |  | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	start_script_data_out=(unsigned long)&script_data_out[0]; | 
 | 	len_script_data_out=i*4; | 
 | #endif | 
 | 	i=0; | 
 | 	script_data_in[i++]=swap_script(SCR_MOVE_ABS(pccb->datalen)^ SCR_DATA_IN); /* move  */ | 
 | 	script_data_in[i++]=swap_script(phys_to_bus(pccb->pdata)); /* pointer to buffer */ | 
 | 	script_data_in[i++]=swap_script(SCR_JUMP ^ IFTRUE (WHEN (SCR_STATUS))); | 
 | 	script_data_in[i++]=swap_script(phys_to_bus(&script_status[0])); | 
 | 	script_data_in[i++]=swap_script(SCR_INT); | 
 | 	script_data_in[i++]=SIR_DATA_IN_ERR; | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	start_script_data_in=(unsigned long)&script_data_in[0]; | 
 | 	len_script_data_in=i*4; | 
 | #endif | 
 | 	i=0; | 
 | 	script_msgin[i++]=swap_script(SCR_MOVE_ABS (1) ^ SCR_MSG_IN); | 
 | 	script_msgin[i++]=swap_script(phys_to_bus(&pccb->msgin[0])); | 
 | 	script_msgin[i++]=swap_script(SCR_JUMP ^ IFTRUE (DATA (M_COMPLETE))); | 
 | 	script_msgin[i++]=swap_script(phys_to_bus(&script_complete[0])); | 
 | 	script_msgin[i++]=swap_script(SCR_JUMP ^ IFTRUE (DATA (M_DISCONNECT))); | 
 | 	script_msgin[i++]=swap_script(phys_to_bus(&script_complete[0])); | 
 | 	script_msgin[i++]=swap_script(SCR_JUMP ^ IFTRUE (DATA (M_SAVE_DP))); | 
 | 	script_msgin[i++]=swap_script(phys_to_bus(&script_complete[0])); | 
 | 	script_msgin[i++]=swap_script(SCR_JUMP ^ IFTRUE (DATA (M_RESTORE_DP))); | 
 | 	script_msgin[i++]=swap_script(phys_to_bus(&script_complete[0])); | 
 | 	script_msgin[i++]=swap_script(SCR_JUMP ^ IFTRUE (DATA (M_EXTENDED))); | 
 | 	script_msgin[i++]=swap_script(phys_to_bus(&script_msg_ext[0])); | 
 | 	script_msgin[i++]=swap_script(SCR_INT); | 
 | 	script_msgin[i++]=SIR_MSG_RECEIVED; | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	start_script_msgin=(unsigned long)&script_msgin[0]; | 
 | 	len_script_msgin=i*4; | 
 | #endif | 
 | 	i=0; | 
 | 	script_msg_ext[i++]=swap_script(SCR_CLR (SCR_ACK)); /* clear ACK */ | 
 | 	script_msg_ext[i++]=0; | 
 | 	script_msg_ext[i++]=swap_script(SCR_MOVE_ABS (1) ^ SCR_MSG_IN); /* assuming this is the msg length */ | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&pccb->msgin[1])); | 
 | 	script_msg_ext[i++]=swap_script(SCR_JUMP ^ IFFALSE (IF (SCR_MSG_IN))); | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&script_complete[0])); /* no more bytes */ | 
 | 	script_msg_ext[i++]=swap_script(SCR_MOVE_ABS (1) ^ SCR_MSG_IN); /* next */ | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&pccb->msgin[2])); | 
 | 	script_msg_ext[i++]=swap_script(SCR_JUMP ^ IFFALSE (IF (SCR_MSG_IN))); | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&script_complete[0])); /* no more bytes */ | 
 | 	script_msg_ext[i++]=swap_script(SCR_MOVE_ABS (1) ^ SCR_MSG_IN); /* next */ | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&pccb->msgin[3])); | 
 | 	script_msg_ext[i++]=swap_script(SCR_JUMP ^ IFFALSE (IF (SCR_MSG_IN))); | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&script_complete[0])); /* no more bytes */ | 
 | 	script_msg_ext[i++]=swap_script(SCR_MOVE_ABS (1) ^ SCR_MSG_IN); /* next */ | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&pccb->msgin[4])); | 
 | 	script_msg_ext[i++]=swap_script(SCR_JUMP ^ IFFALSE (IF (SCR_MSG_IN))); | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&script_complete[0])); /* no more bytes */ | 
 | 	script_msg_ext[i++]=swap_script(SCR_MOVE_ABS (1) ^ SCR_MSG_IN); /* next */ | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&pccb->msgin[5])); | 
 | 	script_msg_ext[i++]=swap_script(SCR_JUMP ^ IFFALSE (IF (SCR_MSG_IN))); | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&script_complete[0])); /* no more bytes */ | 
 | 	script_msg_ext[i++]=swap_script(SCR_MOVE_ABS (1) ^ SCR_MSG_IN); /* next */ | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&pccb->msgin[6])); | 
 | 	script_msg_ext[i++]=swap_script(SCR_JUMP ^ IFFALSE (IF (SCR_MSG_IN))); | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&script_complete[0])); /* no more bytes */ | 
 | 	script_msg_ext[i++]=swap_script(SCR_MOVE_ABS (1) ^ SCR_MSG_IN); /* next */ | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&pccb->msgin[7])); | 
 | 	script_msg_ext[i++]=swap_script(SCR_JUMP ^ IFFALSE (IF (SCR_MSG_IN))); | 
 | 	script_msg_ext[i++]=swap_script(phys_to_bus(&script_complete[0])); /* no more bytes */ | 
 | 	script_msg_ext[i++]=swap_script(SCR_INT); | 
 | 	script_msg_ext[i++]=SIR_MSG_OVER7; | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	start_script_msg_ext=(unsigned long)&script_msg_ext[0]; | 
 | 	len_script_msg_ext=i*4; | 
 | #endif | 
 | 	i=0; | 
 | 	script_status[i++]=swap_script(SCR_MOVE_ABS (1) ^ SCR_STATUS); | 
 | 	script_status[i++]=swap_script(phys_to_bus(&pccb->status)); | 
 | 	script_status[i++]=swap_script(SCR_JUMP ^ IFTRUE (WHEN (SCR_MSG_IN))); | 
 | 	script_status[i++]=swap_script(phys_to_bus(&script_msgin[0])); | 
 | 	script_status[i++]=swap_script(SCR_INT); | 
 | 	script_status[i++]=SIR_STATUS_ILL_PH; | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	start_script_status=(unsigned long)&script_status[0]; | 
 | 	len_script_status=i*4; | 
 | #endif | 
 | 	i=0; | 
 | 	script_complete[i++]=swap_script(SCR_REG_REG (SCNTL2, SCR_AND, 0x7f)); | 
 | 	script_complete[i++]=0; | 
 | 	script_complete[i++]=swap_script(SCR_CLR (SCR_ACK|SCR_ATN)); | 
 | 	script_complete[i++]=0; | 
 | 	script_complete[i++]=swap_script(SCR_WAIT_DISC); | 
 | 	script_complete[i++]=0; | 
 | 	script_complete[i++]=swap_script(SCR_REG_REG(GPREG, SCR_OR, 0x01)); | 
 | 	script_complete[i++]=0; /* LED OFF */ | 
 | 	script_complete[i++]=swap_script(SCR_INT); | 
 | 	script_complete[i++]=SIR_COMPLETE; | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	start_script_complete=(unsigned long)&script_complete[0]; | 
 | 	len_script_complete=i*4; | 
 | #endif | 
 | 	i=0; | 
 | 	script_error[i++]=swap_script(SCR_INT); /* interrupt if error */ | 
 | 	script_error[i++]=SIR_SCRIPT_ERROR; | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	start_script_error=(unsigned long)&script_error[0]; | 
 | 	len_script_error=i*4; | 
 | #endif | 
 | 	i=0; | 
 | 	script_reselection[i++]=swap_script(SCR_CLR (SCR_TRG)); /* target status */ | 
 | 	script_reselection[i++]=0; | 
 | 	script_reselection[i++]=swap_script(SCR_WAIT_RESEL); | 
 | 	script_reselection[i++]=swap_script(phys_to_bus(&script_select[0])); /* len = 4 */ | 
 | #ifdef SCSI_SINGLE_STEP | 
 | 	start_script_reselection=(unsigned long)&script_reselection[0]; | 
 | 	len_script_reselection=i*4; | 
 | #endif | 
 | } | 
 |  | 
 |  | 
 | void scsi_issue(ccb *pccb) | 
 | { | 
 | 	int busdevfunc = pccb->priv; | 
 | 	int i; | 
 | 	unsigned short sstat; | 
 | 	int retrycnt;  /* retry counter */ | 
 | 	for(i=0;i<3;i++) | 
 | 		int_stat[i]=0; /* delete all int status */ | 
 | 	/* struct pccb must be set-up correctly */ | 
 | 	retrycnt=0; | 
 | 	PRINTF("ID %d issue cmd %02X\n",pccb->target,pccb->cmd[0]); | 
 | 	pccb->trans_bytes=0; /* no bytes transfered yet */ | 
 | 	scsi_set_script(pccb); /* fill in SCRIPT		*/ | 
 | 	scsi_int_mask=STO | UDC | MA; /* | CMP; / * Interrupts which are enabled */ | 
 | 	script_int_mask=0xff; /* enable all Ints */ | 
 | 	scsi_int_enable(); | 
 | 	scsi_write_dsp(phys_to_bus(&script_select[0])); /* start script */ | 
 | 	/* now we have to wait for IRQs */ | 
 | retry: | 
 | 	/* | 
 | 	 * This version of the driver is _not_ interrupt driven, | 
 | 	 * but polls the chip's interrupt registers (ISTAT, DSTAT). | 
 | 	 */ | 
 | 	while(int_stat[0]==0) | 
 | 		handle_scsi_int(); | 
 |  | 
 | 	if(int_stat[0]==SIR_COMPLETE) { | 
 | 		if(pccb->msgin[0]==M_DISCONNECT) { | 
 | 			PRINTF("Wait for reselection\n"); | 
 | 			for(i=0;i<3;i++) | 
 | 				int_stat[i]=0; /* delete all int status */ | 
 | 			scsi_write_dsp(phys_to_bus(&script_reselection[0])); /* start reselection script */ | 
 | 			goto retry; | 
 | 		} | 
 | 		pccb->contr_stat=SIR_COMPLETE; | 
 | 		return; | 
 | 	} | 
 | 	if((int_stat[0] & SCSI_INT_STATE)==SCSI_INT_STATE) { /* scsi interrupt */ | 
 | 		sstat=(unsigned short)int_stat[0]; | 
 | 		if((sstat & STO)==STO) { /* selection timeout */ | 
 | 			pccb->contr_stat=SCSI_SEL_TIME_OUT; | 
 | 			scsi_write_byte(GPREG,0x01); | 
 | 			PRINTF("ID: %X Selection Timeout\n",pccb->target); | 
 | 			return; | 
 | 		} | 
 | 		if((sstat & UDC)==UDC) { /* unexpected disconnect */ | 
 | 			pccb->contr_stat=SCSI_UNEXP_DIS; | 
 | 			scsi_write_byte(GPREG,0x01); | 
 | 			PRINTF("ID: %X Unexpected Disconnect\n",pccb->target); | 
 | 			return; | 
 | 		} | 
 | 		if((sstat & RSL)==RSL) { /* reselection */ | 
 | 			pccb->contr_stat=SCSI_UNEXP_DIS; | 
 | 			scsi_write_byte(GPREG,0x01); | 
 | 			PRINTF("ID: %X Unexpected Disconnect\n",pccb->target); | 
 | 			return; | 
 | 		} | 
 | 		if(((sstat & MA)==MA)||((sstat & HTH)==HTH)) { /* phase missmatch */ | 
 | 			if(retrycnt<SCSI_MAX_RETRY) { | 
 | 				pccb->trans_bytes=pccb->datalen - | 
 | 					((unsigned long)scsi_read_byte(DBC) | | 
 | 					((unsigned long)scsi_read_byte(DBC+1)<<8) | | 
 | 					((unsigned long)scsi_read_byte(DBC+2)<<16)); | 
 | 				for(i=0;i<3;i++) | 
 | 					int_stat[i]=0; /* delete all int status */ | 
 | 				retrycnt++; | 
 | 				PRINTF("ID: %X Phase Missmatch Retry %d Phase %02X transfered %lx\n", | 
 | 						pccb->target,retrycnt,scsi_read_byte(SBCL),pccb->trans_bytes); | 
 | 				scsi_write_dsp(phys_to_bus(&script_cmd[4])); /* start retry script */ | 
 | 				goto retry; | 
 | 			} | 
 | 			if((sstat & MA)==MA) | 
 | 				pccb->contr_stat=SCSI_MA_TIME_OUT; | 
 | 			else | 
 | 				pccb->contr_stat=SCSI_HNS_TIME_OUT; | 
 | 			PRINTF("Phase Missmatch stat %lx\n",pccb->contr_stat); | 
 | 			return; | 
 | 		} /* no phase int */ | 
 | /*		if((sstat & CMP)==CMP) { | 
 | 			pccb->contr_stat=SIR_COMPLETE; | 
 | 			return; | 
 | 		} | 
 | */ | 
 | 		PRINTF("SCSI INT %lX\n",int_stat[0]); | 
 | 		pccb->contr_stat=int_stat[0]; | 
 | 		return; | 
 | 	} /* end scsi int */ | 
 | 	PRINTF("SCRIPT INT %lX phase %02X\n",int_stat[0],scsi_read_byte(SBCL)); | 
 | 	pccb->contr_stat=int_stat[0]; | 
 | 	return; | 
 | } | 
 |  | 
 | int scsi_exec(ccb *pccb) | 
 | { | 
 | 	unsigned char tmpcmd[16],tmpstat; | 
 | 	int i,retrycnt,t; | 
 | 	unsigned long transbytes,datalen; | 
 | 	unsigned char *tmpptr; | 
 | 	retrycnt=0; | 
 | retry: | 
 | 	scsi_issue(pccb); | 
 | 	if(pccb->contr_stat!=SIR_COMPLETE) | 
 | 		return false; | 
 | 	if(pccb->status==S_GOOD) | 
 | 		return true; | 
 | 	if(pccb->status==S_CHECK_COND) { /* check condition */ | 
 | 		for(i=0;i<16;i++) | 
 | 			tmpcmd[i]=pccb->cmd[i]; | 
 | 		pccb->cmd[0]=SCSI_REQ_SENSE; | 
 | 		pccb->cmd[1]=pccb->lun<<5; | 
 | 		pccb->cmd[2]=0; | 
 | 		pccb->cmd[3]=0; | 
 | 		pccb->cmd[4]=14; | 
 | 		pccb->cmd[5]=0; | 
 | 		pccb->cmdlen=6; | 
 | 		pccb->msgout[0]=SCSI_IDENTIFY; | 
 | 		transbytes=pccb->trans_bytes; | 
 | 		tmpptr=pccb->pdata; | 
 | 		pccb->pdata = &pccb->sense_buf[0]; | 
 | 		datalen=pccb->datalen; | 
 | 		pccb->datalen=14; | 
 | 		tmpstat=pccb->status; | 
 | 		scsi_issue(pccb); | 
 | 		for(i=0;i<16;i++) | 
 | 			pccb->cmd[i]=tmpcmd[i]; | 
 | 		pccb->trans_bytes=transbytes; | 
 | 		pccb->pdata=tmpptr; | 
 | 		pccb->datalen=datalen; | 
 | 		pccb->status=tmpstat; | 
 | 		PRINTF("Request_sense sense key %x ASC %x ASCQ %x\n",pccb->sense_buf[2]&0x0f, | 
 | 			pccb->sense_buf[12],pccb->sense_buf[13]); | 
 | 		switch(pccb->sense_buf[2]&0xf) { | 
 | 			case SENSE_NO_SENSE: | 
 | 			case SENSE_RECOVERED_ERROR: | 
 | 				/* seems to be ok */ | 
 | 				return true; | 
 | 				break; | 
 | 			case SENSE_NOT_READY: | 
 | 				if((pccb->sense_buf[12]!=0x04)||(pccb->sense_buf[13]!=0x01)) { | 
 | 					/* if device is not in process of becoming ready */ | 
 | 					return false; | 
 | 					break; | 
 | 				} /* else fall through */ | 
 | 			case SENSE_UNIT_ATTENTION: | 
 | 				if(retrycnt<SCSI_MAX_RETRY_NOT_READY) { | 
 | 					PRINTF("Target %d not ready, retry %d\n",pccb->target,retrycnt); | 
 | 					for(t=0;t<SCSI_NOT_READY_TIME_OUT;t++) | 
 | 						udelay(1000); /* 1sec wait */ | 
 | 					retrycnt++; | 
 | 					goto retry; | 
 | 				} | 
 | 				PRINTF("Target %d not ready, %d retried\n",pccb->target,retrycnt); | 
 | 				return false; | 
 | 			default: | 
 | 				return false; | 
 | 		} | 
 | 	} | 
 | 	PRINTF("Status = %X\n",pccb->status); | 
 | 	return false; | 
 | } | 
 |  | 
 |  | 
 | void scsi_chip_init(void) | 
 | { | 
 | 	/* first we issue a soft reset */ | 
 | 	scsi_write_byte(ISTAT,SRST); | 
 | 	udelay(1000); | 
 | 	scsi_write_byte(ISTAT,0); | 
 | 	/* setup chip */ | 
 | 	scsi_write_byte(SCNTL0,0xC0); /* full arbitration no start, no message, parity disabled, master */ | 
 | 	scsi_write_byte(SCNTL1,0x00); | 
 | 	scsi_write_byte(SCNTL2,0x00); | 
 | #ifndef CONFIG_SYS_SCSI_SYM53C8XX_CCF    /* config value for none 40 MHz clocks */ | 
 | 	scsi_write_byte(SCNTL3,0x13); /* synchronous clock 40/4=10MHz, asynchronous 40MHz */ | 
 | #else | 
 | 	scsi_write_byte(SCNTL3,CONFIG_SYS_SCSI_SYM53C8XX_CCF); /* config value for none 40 MHz clocks */ | 
 | #endif | 
 | 	scsi_write_byte(SCID,0x47); /* ID=7, enable reselection */ | 
 | 	scsi_write_byte(SXFER,0x00); /* synchronous transfer period 10MHz, asynchronous */ | 
 | 	scsi_write_byte(SDID,0x00);  /* targed SCSI ID = 0 */ | 
 | 	scsi_int_mask=0x0000; /* no Interrupt is enabled */ | 
 | 	script_int_mask=0x00; | 
 | 	scsi_int_enable(); | 
 | 	scsi_write_byte(GPREG,0x01); /* GPIO0 is LED (off) */ | 
 | 	scsi_write_byte(GPCNTL,0x0E); /* GPIO0 is Output */ | 
 | 	scsi_write_byte(STIME0,0x08); /* handshake timer disabled, selection timeout 512msec */ | 
 | 	scsi_write_byte(RESPID,0x80); /* repond only to the own ID (reselection) */ | 
 | 	scsi_write_byte(STEST1,0x00); /* not isolated, SCLK is used */ | 
 | 	scsi_write_byte(STEST2,0x00); /* no Lowlevel Mode? */ | 
 | 	scsi_write_byte(STEST3,0x80); /* enable tolerANT */ | 
 | 	scsi_write_byte(CTEST3,0x04); /* clear FIFO */ | 
 | 	scsi_write_byte(CTEST4,0x00); | 
 | 	scsi_write_byte(CTEST5,0x00); | 
 | #ifdef SCSI_SINGLE_STEP | 
 | /*	scsi_write_byte(DCNTL,IRQM | SSM);	*/ | 
 | 	scsi_write_byte(DCNTL,IRQD | SSM); | 
 | 	scsi_write_byte(DMODE,MAN); | 
 | #else | 
 | /*	scsi_write_byte(DCNTL,IRQM);	*/ | 
 | 	scsi_write_byte(DCNTL,IRQD); | 
 | 	scsi_write_byte(DMODE,0x00); | 
 | #endif | 
 | } | 
 | #endif |