| menu "NAND Device Support" | |
| config SYS_NAND_SELF_INIT | |
| bool | |
| help | |
| This option, if enabled, provides more flexible and linux-like | |
| NAND initialization process. | |
| config NAND_DENALI | |
| bool "Support Denali NAND controller" | |
| select SYS_NAND_SELF_INIT | |
| help | |
| Enable support for the Denali NAND controller. | |
| config SYS_NAND_DENALI_64BIT | |
| bool "Use 64-bit variant of Denali NAND controller" | |
| depends on NAND_DENALI | |
| help | |
| The Denali NAND controller IP has some variations in terms of | |
| the bus interface. The DMA setup sequence is completely differenct | |
| between 32bit / 64bit AXI bus variants. | |
| If your Denali NAND controller is the 64-bit variant, say Y. | |
| Otherwise (32 bit), say N. | |
| config NAND_DENALI_SPARE_AREA_SKIP_BYTES | |
| int "Number of bytes skipped in OOB area" | |
| depends on NAND_DENALI | |
| range 0 63 | |
| help | |
| This option specifies the number of bytes to skip from the beginning | |
| of OOB area before last ECC sector data starts. This is potentially | |
| used to preserve the bad block marker in the OOB area. | |
| config NAND_VF610_NFC | |
| bool "Support for Freescale NFC for VF610/MPC5125" | |
| select SYS_NAND_SELF_INIT | |
| help | |
| Enables support for NAND Flash Controller on some Freescale | |
| processors like the VF610, MPC5125, MCF54418 or Kinetis K70. | |
| The driver supports a maximum 2k page size. The driver | |
| currently does not support hardware ECC. | |
| choice | |
| prompt "Hardware ECC strength" | |
| depends on NAND_VF610_NFC | |
| default SYS_NAND_VF610_NFC_45_ECC_BYTES | |
| help | |
| Select the ECC strength used in the hardware BCH ECC block. | |
| config SYS_NAND_VF610_NFC_45_ECC_BYTES | |
| bool "24-error correction (45 ECC bytes)" | |
| config SYS_NAND_VF610_NFC_60_ECC_BYTES | |
| bool "32-error correction (60 ECC bytes)" | |
| endchoice | |
| config NAND_PXA3XX | |
| bool "Support for NAND on PXA3xx and Armada 370/XP/38x" | |
| select SYS_NAND_SELF_INIT | |
| help | |
| This enables the driver for the NAND flash device found on | |
| PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). | |
| config NAND_SUNXI | |
| bool "Support for NAND on Allwinner SoCs in SPL" | |
| depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I | |
| select SYS_NAND_SELF_INIT | |
| ---help--- | |
| Enable support for NAND. This option allows SPL to read from | |
| sunxi NAND using DMA transfers. | |
| comment "Generic NAND options" | |
| # Enhance depends when converting drivers to Kconfig which use this config | |
| # option (mxc_nand, ndfc, omap_gpmc). | |
| config SYS_NAND_BUSWIDTH_16BIT | |
| bool "Use 16-bit NAND interface" | |
| depends on NAND_VF610_NFC | |
| help | |
| Indicates that NAND device has 16-bit wide data-bus. In absence of this | |
| config, bus-width of NAND device is assumed to be either 8-bit and later | |
| determined by reading ONFI params. | |
| Above config is useful when NAND device's bus-width information cannot | |
| be determined from on-chip ONFI params, like in following scenarios: | |
| - SPL boot does not support reading of ONFI parameters. This is done to | |
| keep SPL code foot-print small. | |
| - In current U-Boot flow using nand_init(), driver initialization | |
| happens in board_nand_init() which is called before any device probe | |
| (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are | |
| not available while configuring controller. So a static CONFIG_NAND_xx | |
| is needed to know the device's bus-width in advance. | |
| # Enhance depends when converting drivers to Kconfig which use this config | |
| config SYS_NAND_U_BOOT_OFFS | |
| hex "Location in NAND to read U-Boot from" | |
| default 0x8000 if NAND_SUNXI | |
| depends on NAND_SUNXI | |
| help | |
| Set the offset from the start of the nand where u-boot should be | |
| loaded from. | |
| if SPL | |
| config SPL_NAND_DENALI | |
| bool "Support Denali NAND controller for SPL" | |
| help | |
| This is a small implementation of the Denali NAND controller | |
| for use on SPL. | |
| endif | |
| endmenu |