| #CW_MODE settings configuration |
| # |
| CW_MODE={ |
| #Mode of operation 0: Disable current Tx Mode, 1: Continuous Tx Packet, 2: Continuous Wave/Tone |
| Mode=1 |
| #Channel number |
| Channel=6 |
| #channel Info |
| #bit [3:0] - channel offset 0: no secondary channel, 1: secondary channel above, 2: reserved, 3: secondary channel below |
| #bit [4:7] - channel band 0: 2.4G, 1: 5G, 2: 4G, 3: reserved |
| Chaninfo=0x00 |
| #Tx power for Cont Tx in dbm |
| TxPower=12 |
| # Packet Length for Cont Tx |
| # legacy rates: upto 2312, HT/VHT rates: upto 8K |
| PktLength=2048 |
| #RateInfo for Cont Tx |
| RateInfo=0x0000 |
| #rateInfo = 0x0732 : format = VHT, Bandwidth = 80MHz, datarate/MCS index = MCS7 |
| #rateInfo = 0x0000 : format = legacy, Bandwidth = 20MHz, datarate/MCS index = 1Mbps |
| #rateInfo = 0x0521 : format = HT, Bandwidth = 40MHz, datarate/MCS index = MCS5 |
| #rateInfo = 0x4521 : format = HT, Bandwidth = 40MHz, datarate/MCS index = MCS5, NSS = 1 |
| #rateInfo = 0x8921 : format = HT, Bandwidth = 40MHz, datarate/MCS index = MCS9, NSS = 2 |
| #bit [1:0] - Format 0: legacy, 1: 11n (HT), 2: 11ac (VHT) |
| #bit 2 - STBC (Not used for Cont Tx test) |
| #bit 3 - Beamforming (Not used for Cont Tx test) |
| #bit [5:4] - Bandwidth 0: 20MHz, 2: 40MHz, 3: 80MHz |
| #bit [7:6] - reserved |
| #bit [13:8] - index : data rate or MCS |
| #bit [15:14]- NSS (Used for 2x2 chips). Used in FW only for 2x2 chips. |
| #<index> can take following values. |
| #If <format> is 0 (LG), #If <format> is 1 (HT) #If <format> is 2 (VHT) |
| # NSS = 1 NSS = 1 or 2 |
| # 0 1 Mbps 0 MCS0 0 MCS0 |
| # 1 2 Mbps 1 MCS1 1 MCS1 |
| # 2 5.5 Mbps 2 MCS2 2 MCS2 |
| # 3 11 Mbps 3 MCS3 3 MCS3 |
| # 5 6 Mbps 4 MCS4 4 MCS4 |
| # 6 9 Mbps 5 MCS5 5 MCS5 |
| # 7 12 Mbps 6 MCS6 6 MCS6 |
| # 8 18 Mbps 7 MCS7 7 MCS7 |
| # Used only for NSS = 2 |
| # 9 24 Mbps 8 MCS8 |
| # 10 36 Mbps 9 MCS9 |
| # 11 48 Mbps 10 MCS10 |
| # 12 54 Mbps 11 MCS11 |
| # 12 MCS12 |
| # 13 MCS13 |
| # 14 MCS14 |
| # 15 MCS15 |
| } |
