wlan_sd8897/mapp/mlanconfig/config/mef_mdns.conf

#	File : mef_mdns.conf

######################### MEF Configuration command ##################
mefcfg={
	#Criteria: bit0-broadcast, bit1-unicast, bit3-multicast
	Criteria=8 		# Multicast frames are received during hostsleepmode
	NumEntries=2		# Number of activated MEF entries
	#mef_entry_0: example filters to match WS-Discovery pkt for IPv4.
	mef_entry_0={
		#mode: bit0--hostsleep mode, bit1--non hostsleep mode
		mode=1		# HostSleep mode
		#action: 0--discard and not wake host, 1--discard and wake host 3--allow and wake host
		action=3	# Allow and Wake host
		filter_num=4    # Number of filter
		#RPN only support "&&" and "||" operator,space can not be removed between operator.
		RPN=Filter_0 && Filter_1 && Filter_2 && Filter_3
		#Filter_0 will match IPv4 protocol packet
		Filter_0={
			type=0x41
			repeat=1
			byte=08:00
			offset=20
		}
		#Filter_1 will match dest multicast IPv4 address 224.0.0.251
		Filter_1={
			type=0x41
			repeat=1
			byte=e0:00:00:fb
			offset=38
		}
		#Filter_2 will match UDP packet
		Filter_2={
			type=0x42
			pattern=17
			offset=31
			numbyte=1
		}
		#Filter_3 will match UDP port 5353
		Filter_3={
			type=0x42
			pattern=5353
			offset=44
			numbyte=2
		}
	}
	#mef_entry_1: example filters to match WS-Discovery pkt for IPv6.
	mef_entry_1={
		#mode: bit0--hostsleep mode, bit1--non hostsleep mode
		mode=1		# HostSleep mode
		#action: 0--discard and not wake host, 1--discard and wake host 3--allow and wake host
		action=3	# Allow and Wake host
		filter_num=4    # Number of filter
		#RPN only support "&&" and "||" operator,space can not be removed between operator.
		RPN=Filter_0 && Filter_1 && Filter_2 && Filter_3
		#Filter_0 will match IPv4 protocol packet
		Filter_0={
			type=0x41
			repeat=1
			byte=86:dd
			offset=20
		}
		#Filter_1 will match dest multicast IPv6 address FF02::FB
		Filter_1={
			type=0x41
			repeat=1
			byte=ff:02:00:00:00:00:00:00:00:00:00:00:00:00:00:fb
			offset=46
		}
		#Filter_2 will match UDP packet
		Filter_2={
			type=0x42
			pattern=17
			offset=28
			numbyte=1
		}
		#Filter_3 will match UDP port 5353
		Filter_3={
			type=0x42
			pattern=5353
			offset=64
			numbyte=2
		}
	}
}


#--------------------------examples for MEF filters--------------------------------
#	example: filters to match ARP packet with protocol addr 192.168.0.104
#	mef_entry_0={
#		mode=1			# HostSleep mode
#		action=3		# Allow and Wake host
#		filter_num=3		# Number of filter
#		RPN=Filter_0 && Filter_1 && Filter_2
#		#Filter_0 looking for rx pkt with DA is broadcast address
#		Filter_0={
#			type=0x41
#			repeat=6
#			byte=ff
#			offset=0
#		}
#		#Filter_1 looking for rx pkt with EtherType is 0x0806(ARP)
#		Filter_1={
#			type=0x41
#			repeat=1
#			byte=08:06
#			offset=20
#		}
#		#Filter_2 looking for rx pkt with ARP target protocol addr 192.168.0.104
#		Filter_2={
#			type=0x41
#			repeat=1
#			byte=c0:a8:00:68
#			offset=46
#		}
#	}
#-------------------------------------------------------------------------------------
#	example: filter to check if the destination MAC address is unicast pkt
#	mef_entry_0={
#		mode=1			# HostSleep mode
#		action=3		# Allow and Wake host
#		filter_num=3		# Number of filter
#		RPN=Filter_0
#		#Filter_0 is Bit comparison filter, it always with type=0x43
#		#Byte filter always has type, byte, mask, offset 4 filed
#		#"byte" is the byte sequence constant with each byte in hex format, with ':' as delimiter between two byte
#		#"mask" is also with each byte in hex format, with ':' as delimiter between two byte
#		#"byte" should has the same length as "mask"
#		#Filter_0 will check if the destination MAC address is unicast pkt
#		Filter_0={
#			type=0x43	#Bit comparison filter
#			byte=00		#00 is the 1-byte sequence constant
#			offset=0        #0 is the byte offset of the rx pkt
#			mask=01		#1 is the 1-byte mask
#		}
#	}
#--------------------------------------------------------------------------------------------------
#	example: Disable MEF filters
#	mefcfg={
#		#Criteria: bit0-broadcast, bit1-unicast, bit3-multicast
#		Criteria=2 		# Unicast frames are received during hostsleepmode
#		NumEntries=0		# Number of activated MEF entries
#	}
#--------------------------------------------------------------------------------------------------
#	example: Test MEF filters
#       mefcfg={
#		Criteria=1
#		NumEntries=1
#		mef_entry_0={
#			mode=4         # Test Mode
#			action=16      # Invoke Test
#			filter_num=0
#		}
#	}
#-----------------------------------------------------------------------------------------------------
#	example: Test MEF filters
#       mefcfg={
#		Criteria=1
#		NumEntries=1
#		mef_entry_0={
#			mode=4
#			action=0
#			filter_num=1
#			RPN=Filter_0
#			Filter_0={
#				type=0x44		# test filter
#				repeat=2                # 2 copies of 'BE:EF'
#				byte=BE:EF		# 'BE:EF' is the byte sequence constant
#				offset=18		# 18 is the byte offset of the equal length field of rx'd pkt.
#				dest=00:50:43:20:5a:82  # '00:50:43:20:5a:82' is the byte sequence constant
#			}
#		}
#	}
#----------------------------------------------------------------------------------------------------
#example: Filter broadcast/ipv4 multicast/ipv6 multicast packets in non hostsleep mode
#mefcfg={
#	Criteria=9		# broadcast and multicast frames
#	NumEntries=1	# Number of activated MEF entries
#	mef_entry_0={
#		mode=2		# non HostSleep mode
#		action=0	# discard and not wake host
#		filter_num=3    # Number of filter
#		RPN=Filter_0 || Filter_1 || Filter_2
#		Filter_0={              # IPV4 multicast
#			type=0x41	        # byte comparison filter
#			byte=01:00:5e		# 01:00:5e is the byte constant to be compared
#			offset=0	        # 0 is the byte offset of the equal length field of rx'd pkt.
#			repeat=1		    #
#		}
#		Filter_1={              # broadcast packet check
#			type=0x41          	# Byte comparison filter
#			repeat=6            # 6 copies of 'ff', means broadcast
#			byte=ff			    # 'ff'(0xff) is the byte sequence constant with each byte
#						        # in hex format, with ':' as delimiter between two byte.
#			offset=0            # 0 is the byte offset of the equal length field of rx'd pkt.
#		}
#		Filter_2={              # IPV6 multicast
#			type=0x41	        # byte comparison filter
#			byte=33:33		    # 33:33 is the byte constant to be compared
#			offset=0	        # 0 is the byte offset of the equal length field of rx'd pkt.
#			repeat=1		    #
#		}
#	}
#}
#------------------------------------------------------------------------------------------------------