man/man8/tc-taprio.8

.TH TAPRIO 8 "25 Sept 2018" "iproute2" "Linux"
.SH NAME
TAPRIO \- Time Aware Priority Shaper
.SH SYNOPSIS
.B tc qdisc ... dev
dev
.B parent
classid
.B [ handle
major:
.B ] taprio num_tc
tcs
.ti +8
.B map
P0 P1 P2 ...
.B queues
count1@offset1 count2@offset2 ...
.ti +8
.B base-time
base-time
.B clockid
clockid
.ti +8
.B sched-entry
<command 1> <gate mask 1> <interval 1>
.ti +8
.B sched-entry
<command 2> <gate mask 2> <interval 2>
.ti +8
.B sched-entry
<command 3> <gate mask 3> <interval 3>
.ti +8
.B sched-entry
<command N> <gate mask N> <interval N>

.SH DESCRIPTION
The TAPRIO qdisc implements a simplified version of the scheduling
state machine defined by IEEE 802.1Q-2018 Section 8.6.9, which allows
configuration of a sequence of gate states, where each gate state
allows outgoing traffic for a subset (potentially empty) of traffic
classes.

How traffic is mapped to different hardware queues is similar to
.BR mqprio(8)
and so the
.B map
and
.B queues
parameters have the same meaning.

The other parameters specify the schedule, and at what point in time
it should start (it can behave as the schedule started in the past).

.SH PARAMETERS
.TP
num_tc
.BR
Number of traffic classes to use. Up to 16 classes supported.

.TP
map
.br
The priority to traffic class map. Maps priorities 0..15 to a specified
traffic class. See
.BR mqprio(8)
for more details.

.TP
queues
.br
Provide count and offset of queue range for each traffic class. In the
format,
.B count@offset.
Queue ranges for each traffic classes cannot overlap and must be a
contiguous range of queues.

.TP
base-time
.br
Specifies the instant in nanoseconds, using the reference of
.B clockid,
defining the time when the schedule starts. If 'base-time' is a time
in the past, the schedule will start at

base-time + (N * cycle-time)

where N is the smallest integer so the resulting time is greater than
"now", and "cycle-time" is the sum of all the intervals of the entries
in the schedule;

.TP
clockid
.br
Specifies the clock to be used by qdisc's internal timer for measuring
time and scheduling events.

.TP
sched-entry
.br
There may multiple
.B sched-entry
parameters in a single schedule. Each one has the

sched-entry <command> <gatemask> <interval>

format. The only supported <command> is "S", which
means "SetGateStates", following the IEEE 802.1Q-2018 definition
(Table 8-7). <gate mask> is a bitmask where each bit is a associated
with a traffic class, so bit 0 (the least significant bit) being "on"
means that traffic class 0 is "active" for that schedule entry.
<interval> is a time duration, in nanoseconds, that specifies for how
long that state defined by <command> and <gate mask> should be held
before moving to the next entry.

.TP
flags
.br
Specifies different modes for taprio. Currently, only txtime-assist is
supported which can be enabled by setting it to 0x1. In this mode, taprio will
set the transmit timestamp depending on the interval in which the packet needs
to be transmitted. It will then utililize the
.BR etf(8)
qdisc to sort and transmit the packets at the right time. The second example
can be used as a reference to configure this mode.

.TP
txtime-delay
.br
This parameter is specific to the txtime offload mode. It specifies the maximum
time a packet might take to reach the network card from the taprio qdisc. The
value should always be greater than the delta specified in the
.BR etf(8)
qdisc.

.SH EXAMPLES

The following example shows how an traffic schedule with three traffic
classes ("num_tc 3"), which are separated different traffic classes,
we are going to call these TC 0, TC 1 and TC 2. We could read the
"map" parameter below as: traffic with priority 3 is classified as TC
0, priority 2 is classified as TC 1 and the rest is classified as TC
2.

The schedule will start at instant 1528743495910289987 using the
reference CLOCK_TAI. The schedule is composed of three entries each of
300us duration.

.EX
# tc qdisc replace dev eth0 parent root handle 100 taprio \\
              num_tc 3 \\
              map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \\
              queues 1@0 1@1 2@2 \\
              base-time 1528743495910289987 \\
              sched-entry S 01 300000 \\
              sched-entry S 02 300000 \\
              sched-entry S 04 300000 \\
              clockid CLOCK_TAI
.EE

Following is an example to enable the txtime offload mode in taprio. See
.BR etf(8)
for more information about configuring the ETF qdisc.

.EX
# tc qdisc replace dev eth0 parent root handle 100 taprio \\
              num_tc 3 \\
              map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \\
              queues 1@0 1@0 1@0 \\
              base-time 1528743495910289987 \\
              sched-entry S 01 300000 \\
              sched-entry S 02 300000 \\
              sched-entry S 04 400000 \\
              flags 0x1 \\
              txtime-delay 200000 \\
              clockid CLOCK_TAI

# tc qdisc replace dev $IFACE parent 100:1 etf skip_skb_check \\
              offload delta 200000 clockid CLOCK_TAI
.EE

.SH AUTHORS
Vinicius Costa Gomes <vinicius.gomes@intel.com>