| /* |
| * arch/arm/boot/dts/amlogic/mesong12b_a.dtsi |
| * |
| * Copyright (C) 2017 Amlogic, Inc. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, but WITHOUT |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for |
| * more details. |
| * |
| */ |
| |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/clock/amlogic,g12a-clkc.h> |
| #include <dt-bindings/clock/amlogic,g12a-audio-clk.h> |
| #include <dt-bindings/iio/adc/amlogic-saradc.h> |
| #include <dt-bindings/gpio/meson-g12a-gpio.h> |
| #include <dt-bindings/pwm/pwm.h> |
| #include <dt-bindings/pwm/meson.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/input/meson_rc.h> |
| #include <dt-bindings/phy/phy-amlogic-pcie.h> |
| #include "mesong12a-bifrost.dtsi" |
| #include "g12b-sched-energy-a.dtsi" |
| |
| / { |
| cpus:cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu-map { |
| cluster0:cluster0 { |
| core0 { |
| cpu = <&CPU0>; |
| }; |
| core1 { |
| cpu = <&CPU1>; |
| }; |
| }; |
| cluster1:cluster1 { |
| core0 { |
| cpu = <&CPU2>; |
| }; |
| core1 { |
| cpu = <&CPU3>; |
| }; |
| core2 { |
| cpu = <&CPU4>; |
| }; |
| core3 { |
| cpu = <&CPU5>; |
| }; |
| }; |
| }; |
| |
| CPU0:cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53","arm,armv8"; |
| reg = <0x0>; |
| enable-method = "psci"; |
| //cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; |
| sched-energy-costs = <&CPU_COST_A53 &CLUSTER_COST_A53>; |
| clocks = <&clkc CLKID_CPU_CLK>, |
| <&clkc CLKID_CPU_FCLK_P>, |
| <&clkc CLKID_SYS1_PLL>; |
| clock-names = "core_clk", |
| "low_freq_clk_parent", |
| "high_freq_clk_parent"; |
| operating-points-v2 = <&cpu_opp_table0>; |
| cpu-supply = <&vddcpu0>; |
| voltage-tolerance = <0>; |
| clock-latency = <50000>; |
| }; |
| |
| CPU1:cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53","arm,armv8"; |
| reg = <0x1>; |
| enable-method = "psci"; |
| sched-energy-costs = <&CPU_COST_A53 &CLUSTER_COST_A53>; |
| clocks = <&clkc CLKID_CPU_CLK>, |
| <&clkc CLKID_CPU_FCLK_P>, |
| <&clkc CLKID_SYS1_PLL>; |
| clock-names = "core_clk", |
| "low_freq_clk_parent", |
| "high_freq_clk_parent"; |
| operating-points-v2 = <&cpu_opp_table0>; |
| cpu-supply = <&vddcpu0>; |
| voltage-tolerance = <0>; |
| clock-latency = <50000>; |
| }; |
| |
| CPU2:cpu@100 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a73","arm,armv8"; |
| reg = <0x100>; |
| enable-method = "psci"; |
| //cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; |
| sched-energy-costs = <&CPU_COST_A73 &CLUSTER_COST_A73>; |
| clocks = <&clkc CLKID_CPUB_CLK>, |
| <&clkc CLKID_CPUB_FCLK_P>, |
| <&clkc CLKID_SYS_PLL>; |
| clock-names = "core_clk", |
| "low_freq_clk_parent", |
| "high_freq_clk_parent"; |
| operating-points-v2 = <&cpu_opp_table1>; |
| cpu-supply = <&vddcpu1>; |
| voltage-tolerance = <0>; |
| clock-latency = <50000>; |
| }; |
| |
| CPU3:cpu@101 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a73","arm,armv8"; |
| reg = <0x101>; |
| enable-method = "psci"; |
| //cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; |
| sched-energy-costs = <&CPU_COST_A73 &CLUSTER_COST_A73>; |
| clocks = <&clkc CLKID_CPUB_CLK>, |
| <&clkc CLKID_CPUB_FCLK_P>, |
| <&clkc CLKID_SYS_PLL>; |
| clock-names = "core_clk", |
| "low_freq_clk_parent", |
| "high_freq_clk_parent"; |
| operating-points-v2 = <&cpu_opp_table1>; |
| cpu-supply = <&vddcpu1>; |
| voltage-tolerance = <0>; |
| clock-latency = <50000>; |
| }; |
| |
| CPU4:cpu@102 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a73","arm,armv8"; |
| reg = <0x102>; |
| enable-method = "psci"; |
| //cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; |
| sched-energy-costs = <&CPU_COST_A73 &CLUSTER_COST_A73>; |
| clocks = <&clkc CLKID_CPUB_CLK>, |
| <&clkc CLKID_CPUB_FCLK_P>, |
| <&clkc CLKID_SYS_PLL>; |
| clock-names = "core_clk", |
| "low_freq_clk_parent", |
| "high_freq_clk_parent"; |
| operating-points-v2 = <&cpu_opp_table1>; |
| cpu-supply = <&vddcpu1>; |
| voltage-tolerance = <0>; |
| clock-latency = <50000>; |
| }; |
| |
| CPU5:cpu@103 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a73","arm,armv8"; |
| reg = <0x103>; |
| enable-method = "psci"; |
| //cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; |
| sched-energy-costs = <&CPU_COST_A73 &CLUSTER_COST_A73>; |
| clocks = <&clkc CLKID_CPUB_CLK>, |
| <&clkc CLKID_CPUB_FCLK_P>, |
| <&clkc CLKID_SYS_PLL>; |
| clock-names = "core_clk", |
| "low_freq_clk_parent", |
| "high_freq_clk_parent"; |
| operating-points-v2 = <&cpu_opp_table1>; |
| cpu-supply = <&vddcpu1>; |
| voltage-tolerance = <0>; |
| clock-latency = <50000>; |
| }; |
| |
| idle-states { |
| entry-method = "arm,psci"; |
| |
| CPU_SLEEP_0: cpu-sleep-0 { |
| compatible = "arm,idle-state"; |
| arm,psci-suspend-param = <0x0010000>; |
| local-timer-stop; |
| entry-latency-us = <8000>; |
| exit-latency-us = <8000>; |
| min-residency-us = <20000>; |
| }; |
| |
| CLUSTER_SLEEP_0: cluster-sleep-0 { |
| compatible = "arm,idle-state"; |
| arm,psci-suspend-param = <0x1010000>; |
| local-timer-stop; |
| entry-latency-us = <9000>; |
| exit-latency-us = <9000>; |
| min-residency-us = <25000>; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| interrupts = <GIC_PPI 13 0xff08>, |
| <GIC_PPI 14 0xff08>, |
| <GIC_PPI 11 0xff08>, |
| <GIC_PPI 10 0xff08>; |
| }; |
| |
| timer_bc { |
| compatible = "arm, meson-bc-timer"; |
| reg= <0xffd0f190 0x4 0xffd0f194 0x4>; |
| timer_name = "Meson TimerF"; |
| clockevent-rating=<300>; |
| clockevent-shift=<20>; |
| clockevent-features=<0x23>; |
| interrupts = <0 60 1>; |
| bit_enable=<16>; |
| bit_mode=<12>; |
| bit_resolution=<0>; |
| }; |
| |
| arm_pmu { |
| compatible = "arm,cortex-a15-pmu"; |
| clusterb-enabled; |
| interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xff634680 0x4>, |
| <0xff6347c0 0x04>; |
| cpumasks = <0x3 0x3C>; |
| /* default 10ms */ |
| relax-timer-ns = <10000000>; |
| /* default 10000us */ |
| max-wait-cnt = <10000>; |
| }; |
| |
| gic: interrupt-controller@2c001000 { |
| compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic"; |
| #interrupt-cells = <3>; |
| #address-cells = <0>; |
| interrupt-controller; |
| reg = <0xffc01000 0x1000>, |
| <0xffc02000 0x0100>; |
| interrupts = <GIC_PPI 9 0xf04>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-0.2"; |
| method = "smc"; |
| }; |
| |
| aml_pm { |
| compatible = "amlogic, pm"; |
| status = "okay"; |
| device_name = "aml_pm"; |
| debug_reg = <0xff8000a8>; |
| exit_reg = <0xff80023c>; |
| }; |
| |
| secmon { |
| compatible = "amlogic, secmon"; |
| memory-region = <&secmon_reserved>; |
| in_base_func = <0x82000020>; |
| out_base_func = <0x82000021>; |
| reserve_mem_size = <0x00300000>; |
| clear_range = <0x05100000 0x200000>; |
| }; |
| |
| securitykey { |
| compatible = "aml, securitykey"; |
| storage_query = <0x82000060>; |
| storage_read = <0x82000061>; |
| storage_write = <0x82000062>; |
| storage_tell = <0x82000063>; |
| storage_verify = <0x82000064>; |
| storage_status = <0x82000065>; |
| storage_list = <0x82000067>; |
| storage_remove = <0x82000068>; |
| storage_in_func = <0x82000023>; |
| storage_out_func = <0x82000024>; |
| storage_block_func = <0x82000025>; |
| storage_size_func = <0x82000027>; |
| storage_set_enctype = <0x8200006A>; |
| storage_get_enctype = <0x8200006B>; |
| storage_version = <0x8200006C>; |
| }; |
| |
| mailbox: mhu@c883c400 { |
| compatible = "amlogic, meson_mhu"; |
| reg = <0xff63c400 0x4c>, /* MHU registers */ |
| <0xfffe7000 0x800>; /* Payload area */ |
| interrupts = <0 209 1>, /* low priority interrupt */ |
| <0 210 1>; /* high priority interrupt */ |
| #mbox-cells = <1>; |
| mbox-names = "cpu_to_scp_low", "cpu_to_scp_high"; |
| mboxes = <&mailbox 0 &mailbox 1>; |
| }; |
| |
| cpu_iomap { |
| compatible = "amlogic, iomap"; |
| #address-cells=<1>; |
| #size-cells=<1>; |
| ranges; |
| io_cbus_base { |
| reg = <0xffd00000 0x26000>; |
| }; |
| io_apb_base { |
| reg = <0xffe01000 0x7f000>; |
| }; |
| io_aobus_base { |
| reg = <0xff800000 0xb000>; |
| }; |
| io_vapb_base { |
| reg = <0xff900000 0x50000>; |
| }; |
| io_hiu_base { |
| reg = <0xff63c000 0x2000>; |
| }; |
| }; |
| |
| xtal: xtal-clk { |
| compatible = "fixed-clock"; |
| clock-frequency = <24000000>; |
| clock-output-names = "xtal"; |
| #clock-cells = <0>; |
| }; |
| |
| cpu_info { |
| compatible = "amlogic, cpuinfo"; |
| status = "okay"; |
| cpuinfo_cmd = <0x82000044>; |
| }; |
| |
| aml_reboot{ |
| compatible = "aml, reboot"; |
| sys_reset = <0x84000009>; |
| sys_poweroff = <0x84000008>; |
| }; |
| |
| vpu { |
| compatible = "amlogic, vpu-g12b"; |
| dev_name = "vpu"; |
| status = "okay"; |
| clocks = <&clkc CLKID_VAPB_MUX>, |
| <&clkc CLKID_VPU_INTR>, |
| <&clkc CLKID_VPU_P0_COMP>, |
| <&clkc CLKID_VPU_P1_COMP>, |
| <&clkc CLKID_VPU_MUX>; |
| clock-names = "vapb_clk", |
| "vpu_intr_gate", |
| "vpu_clk0", |
| "vpu_clk1", |
| "vpu_clk"; |
| clk_level = <7>; |
| /* 0: 100.0M 1: 166.7M 2: 200.0M 3: 250.0M */ |
| /* 4: 333.3M 5: 400.0M 6: 500.0M 7: 666.7M */ |
| }; |
| |
| ethmac: ethernet@ff3f0000 { |
| compatible = "amlogic, g12a-eth-dwmac","snps,dwmac"; |
| reg = <0xff3f0000 0x10000 |
| 0xff634540 0x8 |
| 0xff64c000 0xa0 |
| 0xffd01008 0x4>; |
| reg-names = "eth_base", "eth_cfg", "eth_pll", "eth_reset"; |
| interrupts = <0 8 1>; |
| interrupt-names = "macirq"; |
| status = "disabled"; |
| clocks = <&clkc CLKID_ETH_CORE>; |
| clock-names = "ethclk81"; |
| pll_val = <0x9c0040a 0x927e0000 0xac5f49e5>; |
| analog_val = <0x20200000 0x0000c000 0x00000023>; |
| }; |
| |
| pinctrl_aobus: pinctrl@ff800014{ |
| compatible = "amlogic,meson-g12a-aobus-pinctrl"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gpio_ao: ao-bank@ff800014{ |
| reg = <0xff800014 0x8>, |
| <0xff800024 0x14>, |
| <0xff80001c 0x8>; |
| reg-names = "mux","gpio", "drive-strength"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| |
| pinctrl_periphs: pinctrl@ff634480{ |
| compatible = "amlogic,meson-g12a-periphs-pinctrl"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gpio: banks@ff6346c0{ |
| reg = <0xff6346c0 0x40>, |
| <0xff6344e8 0x18>, |
| <0xff634520 0x18>, |
| <0xff634440 0x4c>, |
| <0xff634740 0x1c>; |
| reg-names = "mux", |
| "pull", |
| "pull-enable", |
| "gpio", |
| "drive-strength"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| |
| audio_data: audio_data { |
| compatible = "amlogic, audio_data"; |
| query_licence_cmd = <0x82000050>; |
| status = "disabled"; |
| }; |
| |
| dwc3: dwc3@ff500000 { |
| compatible = "synopsys, dwc3"; |
| status = "disabled"; |
| reg = <0xff500000 0x100000>; |
| interrupts = <0 30 4>; |
| usb-phy = <&usb2_phy_v2>, <&usb3_phy_v2>; |
| cpu-type = "gxl"; |
| clock-src = "usb3.0"; |
| clocks = <&clkc CLKID_USB_GENERAL>; |
| clock-names = "dwc_general"; |
| }; |
| |
| usb2_phy_v2: usb2phy@ffe09000 { |
| compatible = "amlogic, amlogic-new-usb2-v2"; |
| status = "disabled"; |
| reg = <0xffe09000 0x80 |
| 0xffd01008 0x100 |
| 0xff636000 0x2000 |
| 0xff63a000 0x2000>; |
| pll-setting-1 = <0x09400414>; |
| pll-setting-2 = <0x927E0000>; |
| pll-setting-3 = <0xac5f69e5>; |
| pll-setting-4 = <0xfe18>; |
| pll-setting-5 = <0x8000fff>; |
| pll-setting-6 = <0x78000>; |
| pll-setting-7 = <0xe0004>; |
| pll-setting-8 = <0xe000c>; |
| }; |
| |
| usb3_phy_v2: usb3phy@ffe09080 { |
| compatible = "amlogic, amlogic-new-usb3-v2"; |
| status = "disabled"; |
| reg = <0xffe09080 0x20>; |
| phy-reg = <0xff646000>; |
| phy-reg-size = <0x2000>; |
| usb2-phy-reg = <0xffe09000>; |
| usb2-phy-reg-size = <0x80>; |
| interrupts = <0 16 4>; |
| clocks = <&clkc CLKID_PCIE_PLL>; |
| clock-names = "pcie_refpll"; |
| }; |
| |
| dwc2_a: dwc2_a@ff400000 { |
| compatible = "amlogic, dwc2"; |
| status = "disabled"; |
| device_name = "dwc2_a"; |
| reg = <0xff400000 0x40000>; |
| interrupts = <0 31 4>; |
| pl-periph-id = <0>; /** lm name */ |
| clock-src = "usb0"; /** clock src */ |
| port-id = <0>; /** ref to mach/usb.h */ |
| port-type = <2>; /** 0: otg, 1: host, 2: slave */ |
| port-speed = <0>; /** 0: default, high, 1: full */ |
| port-config = <0>; /** 0: default */ |
| /*0:default,1:single,2:incr,3:incr4,4:incr8,5:incr16,6:disable*/ |
| port-dma = <0>; |
| port-id-mode = <0>; /** 0: hardware, 1: sw_host, 2: sw_slave*/ |
| usb-fifo = <728>; |
| cpu-type = "v2"; |
| phy-reg = <0xffe09000>; |
| phy-reg-size = <0xa0>; |
| /** phy-interface: 0x0: amlogic phy, 0x1: synopsys phy **/ |
| phy-interface = <0x0>; |
| clocks = <&clkc CLKID_USB_GENERAL |
| &clkc CLKID_USB1_TO_DDR>; |
| clock-names = "usb_general", |
| "usb1"; |
| }; |
| |
| wdt: watchdog@0xffd0f0d0 { |
| compatible = "amlogic, meson-wdt"; |
| status = "okay"; |
| default_timeout=<10>; |
| reset_watchdog_method=<1>; /* 0:sysfs,1:kernel */ |
| reset_watchdog_time=<2>; |
| shutdown_timeout=<10>; |
| firmware_timeout=<6>; |
| suspend_timeout=<6>; |
| reg = <0xffd0f0d0 0x10>; |
| clock-names = "xtal"; |
| clocks = <&xtal>; |
| }; |
| |
| jtag { |
| compatible = "amlogic, jtag"; |
| status = "okay"; |
| select = "disable"; /* disable/apao/apee */ |
| pinctrl-names="jtag_apao_pins", "jtag_apee_pins"; |
| pinctrl-0=<&jtag_apao_pins>; |
| pinctrl-1=<&jtag_apee_pins>; |
| }; |
| |
| saradc:saradc { |
| compatible = "amlogic,meson-g12a-saradc"; |
| status = "disabled"; |
| #io-channel-cells = <1>; |
| clocks = <&xtal>, <&clkc CLKID_SARADC_GATE>; |
| clock-names = "xtal", "saradc_clk"; |
| interrupts = <GIC_SPI 200 IRQ_TYPE_EDGE_RISING>; |
| reg = <0xff809000 0x48>; |
| }; |
| |
| p_tsensor: p_tsensor@ff634594 { |
| compatible = "amlogic, r1p1-tsensor"; |
| device_name = "meson-pthermal"; |
| status = "okay"; |
| reg = <0xff634800 0x50>, |
| <0xff800268 0x4>; |
| cal_type = <0x1>; |
| cal_a = <324>; |
| cal_b = <424>; |
| cal_c = <3159>; |
| cal_d = <9411>; |
| rtemp = <115000>; |
| interrupts = <0 35 0>; |
| clocks = <&clkc CLKID_TS_COMP>; /* CLKID_TS_COMP>;*/ |
| clock-names = "ts_comp"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| d_tsensor: d_tsensor@ff800228 { |
| compatible = "amlogic, r1p1-tsensor"; |
| device_name = "meson-dthermal"; |
| status = "okay"; |
| reg = <0xff634c00 0x50>, |
| <0xff800230 0x4>; |
| cal_type = <0x1>; |
| cal_a = <324>; |
| cal_b = <424>; |
| cal_c = <3159>; |
| cal_d = <9411>; |
| rtemp = <115000>; |
| interrupts = <0 36 0>; |
| clocks = <&clkc CLKID_TS_COMP>; /* CLKID_TS_COMP>;*/ |
| clock-names = "ts_comp"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| soc { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| cbus: cbus@ffd00000 { |
| compatible = "simple-bus"; |
| reg = <0xffd00000 0x26000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0xffd00000 0x26000>; |
| |
| gpio_intc: interrupt-controller@f080 { |
| compatible = "amlogic,meson-gpio-intc", |
| "amlogic,meson-g12a-gpio-intc"; |
| reg = <0xf080 0x10>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| amlogic,channel-interrupts = |
| <64 65 66 67 68 69 70 71>; |
| status = "okay"; |
| }; |
| |
| meson_clk_msr { |
| compatible = "amlogic, gxl_measure"; |
| reg = <0x18004 0x4 |
| 0x1800c 0x4>; |
| }; |
| |
| pwm_ab: pwm@1b000 { |
| compatible = "amlogic,g12b-ee-pwm"; |
| reg = <0x1b000 0x20>; |
| #pwm-cells = <3>; |
| clocks = <&xtal>, |
| <&xtal>, |
| <&xtal>, |
| <&xtal>; |
| clock-names = "clkin0", |
| "clkin1", |
| "clkin2", |
| "clkin3"; |
| /* default xtal 24m clkin0-clkin2 and |
| * clkin1-clkin3 should be set the same |
| */ |
| status = "disabled"; |
| }; |
| |
| pwm_cd: pwm@1a000 { |
| compatible = "amlogic,g12b-ee-pwm"; |
| reg = <0x1a000 0x20>; |
| #pwm-cells = <3>; |
| clocks = <&xtal>, |
| <&xtal>, |
| <&xtal>, |
| <&xtal>; |
| clock-names = "clkin0", |
| "clkin1", |
| "clkin2", |
| "clkin3"; |
| status = "disabled"; |
| }; |
| |
| pwm_ef: pwm@19000 { |
| compatible = "amlogic,g12b-ee-pwm"; |
| reg = <0x19000 0x20>; |
| #pwm-cells = <3>; |
| clocks = <&xtal>, |
| <&xtal>, |
| <&xtal>, |
| <&xtal>; |
| clock-names = "clkin0", |
| "clkin1", |
| "clkin2", |
| "clkin3"; |
| status = "disabled"; |
| }; |
| |
| i2c0: i2c@1f000 { |
| compatible = "amlogic,meson-g12b-i2c"; |
| status = "disabled"; |
| reg = <0x1f000 0x20>; |
| interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 91 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clkc CLKID_I2C>; |
| clock-names = "clk_i2c"; |
| }; |
| |
| i2c1: i2c@1e000 { |
| compatible = "amlogic,meson-g12b-i2c"; |
| status = "disabled"; |
| reg = <0x1e000 0x20>; |
| interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 92 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clkc CLKID_I2C>; |
| clock-names = "clk_i2c"; |
| }; |
| |
| i2c2: i2c@1d000 { |
| compatible = "amlogic,meson-g12b-i2c"; |
| status = "disabled"; |
| reg = <0x1d000 0x20>; |
| interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 94 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clkc CLKID_I2C>; |
| clock-names = "clk_i2c"; |
| }; |
| |
| i2c3: i2c@1c000 { |
| compatible = "amlogic,meson-g12b-i2c"; |
| status = "disabled"; |
| reg = <0x1c000 0x20>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 95 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clkc CLKID_I2C>; |
| clock-names = "clk_i2c"; |
| }; |
| |
| spicc0: spi@13000 { |
| compatible = "amlogic,meson-g12b-spicc", |
| "amlogic,meson-g12a-spicc"; |
| reg = <0x13000 0x44>; |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clkc CLKID_SPICC0>, |
| <&clkc CLKID_SPICC0_COMP>; |
| clock-names = "core", "comp"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spicc1: spi@15000 { |
| compatible = "amlogic,meson-g12b-spicc", |
| "amlogic,meson-g12a-spicc"; |
| reg = <0x15000 0x44>; |
| interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clkc CLKID_SPICC1>, |
| <&clkc CLKID_SPICC1_COMP>; |
| clock-names = "core", "comp"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| }; /* end of cbus */ |
| |
| aobus: aobus@ff800000 { |
| compatible = "simple-bus"; |
| reg = <0xff800000 0xb000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0xff800000 0xb000>; |
| |
| cpu_version { |
| reg=<0x220 0x4>; |
| }; |
| |
| aoclkc: clock-controller@0 { |
| compatible = "amlogic,g12b-aoclkc"; |
| #clock-cells = <1>; |
| reg = <0x0 0x320>; |
| }; |
| |
| pwm_AO_ab: pwm@7000 { |
| compatible = "amlogic,g12b-ao-pwm"; |
| reg = <0x7000 0x20>; |
| #pwm-cells = <3>; |
| clocks = <&xtal>, |
| <&xtal>, |
| <&xtal>, |
| <&xtal>; |
| clock-names = "clkin0", |
| "clkin1", |
| "clkin2", |
| "clkin3"; |
| status = "disabled"; |
| }; |
| |
| pwm_AO_cd: pwm@2000 { |
| compatible = "amlogic,g12b-ao-pwm"; |
| reg = <0x2000 0x20>; |
| #pwm-cells = <3>; |
| clocks = <&xtal>, |
| <&xtal>, |
| <&xtal>, |
| <&xtal>; |
| clock-names = "clkin0", |
| "clkin1", |
| "clkin2", |
| "clkin3"; |
| status = "disabled"; |
| }; |
| |
| i2c_AO: i2c@5000 { |
| compatible = "amlogic,meson-g12b-i2c"; |
| status = "disabled"; |
| reg = <0x05000 0x20>; |
| interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 201 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clkc CLKID_I2C>; |
| clock-names = "clk_i2c"; |
| }; |
| |
| i2c_AO_slave:i2c_slave@6000 { |
| compatible = "amlogic, meson-i2c-slave"; |
| status = "disabled"; |
| reg = <0x6000 0x20>; |
| interrupts = <0 194 1>; |
| pinctrl-names="default"; |
| pinctrl-0=<&ao_i2c_slave_pins>; |
| }; |
| |
| uart_AO: serial@3000 { |
| compatible = "amlogic, meson-uart"; |
| reg = <0x3000 0x18>; |
| interrupts = <0 193 1>; |
| status = "okay"; |
| clocks = <&xtal>; |
| clock-names = "clk_uart"; |
| xtal_tick_en = <2>; |
| fifosize = < 64 >; |
| pinctrl-names = "default"; |
| /*pinctrl-0 = <&ao_uart_pins>;*/ |
| support-sysrq = <0>; /* 0 not support*/ |
| }; |
| |
| uart_AO_B: serial@4000 { |
| compatible = "amlogic, meson-uart"; |
| reg = <0x4000 0x18>; |
| interrupts = <0 197 1>; |
| status = "disabled"; |
| clocks = <&xtal>; |
| clock-names = "clk_uart"; |
| fifosize = < 64 >; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ao_b_uart_pins>; |
| }; |
| };/* end of aobus */ |
| |
| periphs: periphs@ff634400 { |
| compatible = "simple-bus"; |
| reg = <0xff634400 0x400>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0xff634400 0x400>; |
| |
| };/* end of periphs */ |
| |
| hiubus: hiubus@ff63c000 { |
| compatible = "simple-bus"; |
| reg = <0xff63c000 0x2000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0xff63c000 0x2000>; |
| |
| clkc: clock-controller@0 { |
| compatible = "amlogic,g12b-clkc-1"; |
| #clock-cells = <1>; |
| reg = <0x0 0x3dc>; |
| }; |
| clkc_b: clock-controller@1 { |
| compatible = "amlogic,g12b-clkc-2"; |
| #clock-cells = <1>; |
| reg = <0x0 0x3dc>; |
| }; |
| };/* end of hiubus*/ |
| |
| ion_dev { |
| compatible = "amlogic, ion_dev"; |
| memory-region = <&ion_cma_reserved>; |
| };/* end of ion_dev*/ |
| |
| audiobus: audiobus@0xff642000 { |
| compatible = "amlogic, audio-controller", "simple-bus"; |
| reg = <0xff642000 0x2000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0xff642000 0x2000>; |
| clkaudio: audio_clocks { |
| compatible = "amlogic, g12a-audio-clocks"; |
| #clock-cells = <1>; |
| reg = <0x0 0xb0>; |
| }; |
| ddr_manager { |
| compatible = "amlogic, g12a-audio-ddr-manager"; |
| interrupts = < |
| GIC_SPI 148 IRQ_TYPE_EDGE_RISING |
| GIC_SPI 149 IRQ_TYPE_EDGE_RISING |
| GIC_SPI 150 IRQ_TYPE_EDGE_RISING |
| GIC_SPI 152 IRQ_TYPE_EDGE_RISING |
| GIC_SPI 153 IRQ_TYPE_EDGE_RISING |
| GIC_SPI 154 IRQ_TYPE_EDGE_RISING |
| >; |
| interrupt-names = |
| "toddr_a", "toddr_b", "toddr_c", |
| "frddr_a", "frddr_b", "frddr_c"; |
| }; |
| };/* end of audiobus*/ |
| |
| }; /* end of soc*/ |
| |
| remote:rc@0xff808040 { |
| compatible = "amlogic, aml_remote"; |
| dev_name = "meson-remote"; |
| reg = <0xff808040 0x44>, /*Multi-format IR controller*/ |
| <0xff808000 0x20>; /*Legacy IR controller*/ |
| status = "okay"; |
| protocol = <REMOTE_TYPE_NEC>; |
| interrupts = <0 196 1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&remote_pins>; |
| map = <&custom_maps>; |
| max_frame_time = <200>; /*set software decoder max frame time*/ |
| }; |
| |
| custom_maps:custom_maps { |
| mapnum = <3>; |
| map0 = <&map_0>; |
| map1 = <&map_1>; |
| map2 = <&map_2>; |
| map_0: map_0{ |
| mapname = "amlogic-remote-1"; |
| customcode = <0xfb04>; |
| release_delay = <80>; |
| size = <50>; /*keymap size*/ |
| keymap = <REMOTE_KEY(0x47, KEY_0) |
| REMOTE_KEY(0x13, KEY_1) |
| REMOTE_KEY(0x10, KEY_2) |
| REMOTE_KEY(0x11, KEY_3) |
| REMOTE_KEY(0x0F, KEY_4) |
| REMOTE_KEY(0x0C, KEY_5) |
| REMOTE_KEY(0x0D, KEY_6) |
| REMOTE_KEY(0x0B, KEY_7) |
| REMOTE_KEY(0x08, KEY_8) |
| REMOTE_KEY(0x09, KEY_9) |
| REMOTE_KEY(0x5C, KEY_RIGHTCTRL) |
| REMOTE_KEY(0x51, KEY_F3) |
| REMOTE_KEY(0x50, KEY_F4) |
| REMOTE_KEY(0x40, KEY_F5) |
| REMOTE_KEY(0x4d, KEY_F6) |
| REMOTE_KEY(0x43, KEY_F7) |
| REMOTE_KEY(0x17, KEY_F8) |
| REMOTE_KEY(0x00, KEY_F9) |
| REMOTE_KEY(0x01, KEY_F10) |
| REMOTE_KEY(0x16, KEY_F11) |
| REMOTE_KEY(0x49, KEY_BACKSPACE) |
| REMOTE_KEY(0x06, KEY_PROPS) |
| REMOTE_KEY(0x14, KEY_UNDO) |
| REMOTE_KEY(0x44, KEY_UP) |
| REMOTE_KEY(0x1D, KEY_DOWN) |
| REMOTE_KEY(0x1C, KEY_LEFT) |
| REMOTE_KEY(0x48, KEY_RIGHT) |
| REMOTE_KEY(0x53, KEY_LEFTMETA) |
| REMOTE_KEY(0x45, KEY_PAGEUP) |
| REMOTE_KEY(0x19, KEY_PAGEDOWN) |
| REMOTE_KEY(0x52, KEY_PAUSE) |
| REMOTE_KEY(0x05, KEY_HANGEUL) |
| REMOTE_KEY(0x59, KEY_HANJA) |
| REMOTE_KEY(0x1b, KEY_SCALE) |
| REMOTE_KEY(0x04, KEY_KPCOMMA) |
| REMOTE_KEY(0x1A, KEY_POWER) |
| REMOTE_KEY(0x0A, KEY_TAB) |
| REMOTE_KEY(0x0e, KEY_MUTE) |
| REMOTE_KEY(0x1F, KEY_HOME) |
| REMOTE_KEY(0x1e, KEY_FRONT) |
| REMOTE_KEY(0x07, KEY_COPY) |
| REMOTE_KEY(0x12, KEY_OPEN) |
| REMOTE_KEY(0x54, KEY_PASTE) |
| REMOTE_KEY(0x02, KEY_FIND) |
| REMOTE_KEY(0x4f, KEY_A) |
| REMOTE_KEY(0x42, KEY_B) |
| REMOTE_KEY(0x5d, KEY_C) |
| REMOTE_KEY(0x4c, KEY_D) |
| REMOTE_KEY(0x58, KEY_CUT) |
| REMOTE_KEY(0x55, KEY_CALC)>; |
| }; |
| map_1: map_1{ |
| mapname = "amlogic-remote-2"; |
| customcode = <0xfe01>; |
| release_delay = <80>; |
| size = <53>; |
| keymap = <REMOTE_KEY(0x01, KEY_1) |
| REMOTE_KEY(0x02, KEY_2) |
| REMOTE_KEY(0x03, KEY_3) |
| REMOTE_KEY(0x04, KEY_4) |
| REMOTE_KEY(0x05, KEY_5) |
| REMOTE_KEY(0x06, KEY_6) |
| REMOTE_KEY(0x07, KEY_7) |
| REMOTE_KEY(0x08, KEY_8) |
| REMOTE_KEY(0x09, KEY_9) |
| REMOTE_KEY(0x0a, KEY_0) |
| REMOTE_KEY(0x1F, KEY_FN_F1) |
| REMOTE_KEY(0x15, KEY_MENU) |
| REMOTE_KEY(0x16, KEY_TAB) |
| REMOTE_KEY(0x0c, KEY_CHANNELUP) |
| REMOTE_KEY(0x0d, KEY_CHANNELDOWN) |
| REMOTE_KEY(0x0e, KEY_VOLUMEUP) |
| REMOTE_KEY(0x0f, KEY_VOLUMEDOWN) |
| REMOTE_KEY(0x11, KEY_HOME) |
| REMOTE_KEY(0x1c, KEY_RIGHT) |
| REMOTE_KEY(0x1b, KEY_LEFT) |
| REMOTE_KEY(0x19, KEY_UP) |
| REMOTE_KEY(0x1a, KEY_DOWN) |
| REMOTE_KEY(0x1d, KEY_ENTER) |
| REMOTE_KEY(0x17, KEY_MUTE) |
| REMOTE_KEY(0x49, KEY_FINANCE) |
| REMOTE_KEY(0x43, KEY_BACK) |
| REMOTE_KEY(0x12, KEY_FN_F4) |
| REMOTE_KEY(0x14, KEY_FN_F5) |
| REMOTE_KEY(0x18, KEY_FN_F6) |
| REMOTE_KEY(0x59, KEY_INFO) |
| REMOTE_KEY(0x5a, KEY_STOPCD) |
| REMOTE_KEY(0x10, KEY_POWER) |
| REMOTE_KEY(0x42, KEY_PREVIOUSSONG) |
| REMOTE_KEY(0x44, KEY_NEXTSONG) |
| REMOTE_KEY(0x1e, KEY_REWIND) |
| REMOTE_KEY(0x4b, KEY_FASTFORWARD) |
| REMOTE_KEY(0x58, KEY_PLAYPAUSE) |
| REMOTE_KEY(0x46, KEY_PROPS) |
| REMOTE_KEY(0x40, KEY_UNDO) |
| REMOTE_KEY(0x38, KEY_SCROLLLOCK) |
| REMOTE_KEY(0x57, KEY_FN) |
| REMOTE_KEY(0x5b, KEY_FN_ESC) |
| REMOTE_KEY(0x54, KEY_RED) |
| REMOTE_KEY(0x4c, KEY_GREEN) |
| REMOTE_KEY(0x4e, KEY_YELLOW) |
| REMOTE_KEY(0x55, KEY_BLUE) |
| REMOTE_KEY(0x53, KEY_BLUETOOTH) |
| REMOTE_KEY(0x52, KEY_WLAN) |
| REMOTE_KEY(0x39, KEY_CAMERA) |
| REMOTE_KEY(0x41, KEY_SOUND) |
| REMOTE_KEY(0x0b, KEY_QUESTION) |
| REMOTE_KEY(0x00, KEY_CHAT) |
| REMOTE_KEY(0x13, KEY_SEARCH)>; |
| }; |
| map_2: map_2{ |
| mapname = "amlogic-remote-3"; |
| customcode = <0xbd02>; |
| release_delay = <80>; |
| size = <17>; |
| keymap = <REMOTE_KEY(0xca,103) |
| REMOTE_KEY(0xd2,108) |
| REMOTE_KEY(0x99,105) |
| REMOTE_KEY(0xc1,106) |
| REMOTE_KEY(0xce,97) |
| REMOTE_KEY(0x45,116) |
| REMOTE_KEY(0xc5,133) |
| REMOTE_KEY(0x80,113) |
| REMOTE_KEY(0xd0,15) |
| REMOTE_KEY(0xd6,125) |
| REMOTE_KEY(0x95,102) |
| REMOTE_KEY(0xdd,104) |
| REMOTE_KEY(0x8c,109) |
| REMOTE_KEY(0x89,131) |
| REMOTE_KEY(0x9c,130) |
| REMOTE_KEY(0x9a,120) |
| REMOTE_KEY(0xcd,121)>; |
| }; |
| }; |
| |
| uart_A: serial@ffd24000 { |
| compatible = "amlogic, meson-uart"; |
| reg = <0xffd24000 0x18>; |
| interrupts = <0 26 1>; |
| status = "disabled"; |
| clocks = <&xtal |
| &clkc CLKID_UART0>; |
| clock-names = "clk_uart", |
| "clk_gate"; |
| fifosize = < 128 >; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&a_uart_pins>; |
| }; |
| |
| uart_B: serial@ffd23000 { |
| compatible = "amlogic, meson-uart"; |
| reg = <0xffd23000 0x18>; |
| interrupts = <0 75 1>; |
| status = "disabled"; |
| clocks = <&xtal |
| &clkc CLKID_UART1>; |
| clock-names = "clk_uart", |
| "clk_gate"; |
| fifosize = < 64 >; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&b_uart_pins>; |
| }; |
| |
| uart_C: serial@ffd22000 { |
| compatible = "amlogic, meson-uart"; |
| reg = <0xffd22000 0x18>; |
| interrupts = <0 93 1>; |
| status = "disabled"; |
| clocks = <&xtal |
| &clkc CLKID_UART1>; |
| clock-names = "clk_uart", |
| "clk_gate"; |
| fifosize = < 64 >; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&c_uart_pins>; |
| }; |
| |
| |
| pcie_A: pcieA@fc000000 { |
| compatible = "amlogic, amlogic-pcie-v2", "snps,dw-pcie"; |
| reg = <0xfc000000 0x400000 |
| 0xff648000 0x2000 |
| 0xfc400000 0x200000 |
| 0xff646000 0x2000 |
| 0xffd01080 0x10>; |
| reg-names = "elbi", "cfg", "config", "phy", "reset"; |
| interrupts = <0 221 0>; |
| #interrupt-cells = <1>; |
| bus-range = <0x0 0xff>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &gic GIC_SPI 223 IRQ_TYPE_EDGE_RISING>; |
| device_type = "pci"; |
| ranges = <0x81000000 0 0 0xfc600000 0x0 0x100000 |
| /* downstream I/O */ |
| 0x82000000 0 0xfc700000 0xfc700000 0 0x1900000>; |
| /* non-prefetchable memory */ |
| num-lanes = <1>; |
| pcie-num = <1>; |
| |
| clocks = <&clkc CLKID_PCIE_PLL |
| &clkc CLKID_PCIE_COMB |
| &clkc CLKID_PCIE_PHY |
| &clkc CLKID_PCIE_HCSL>; |
| clock-names = "pcie_refpll", |
| "pcie", |
| "pcie_phy", |
| "pcie_hcsl"; |
| /*reset-gpio-type 0:Shared pad(no reset)1:OD pad2:Normal pad*/ |
| gpio-type = <2>; |
| pcie-apb-rst-bit = <15>; |
| pcie-phy-rst-bit = <14>; |
| pcie-ctrl-a-rst-bit = <12>; |
| status = "disabled"; |
| }; |
| |
| amhdmitx: amhdmitx{ |
| compatible = "amlogic, amhdmitx"; |
| dev_name = "amhdmitx"; |
| status = "okay"; |
| vend-data = <&vend_data>; |
| pinctrl-names="default", "hdmitx_i2c"; |
| pinctrl-0=<&hdmitx_hpd &hdmitx_ddc>; |
| pinctrl-1=<&hdmitx_hpd_gpio &i2c3_master_pins1>; |
| clocks = <&clkc CLKID_VCLK2_ENCI |
| &clkc CLKID_VCLK2_VENCI0 |
| &clkc CLKID_VCLK2_VENCI1 |
| &clkc CLKID_VAPB_MUX |
| &clkc CLKID_VPU_MUX>; |
| clock-names = "venci_top_gate", |
| "venci_0_gate", |
| "venci_1_gate", |
| "hdmi_vapb_clk", |
| "hdmi_vpu_clk"; |
| /* HPD, 57 + 32 = 89; CEC, 151 + 32 = 183*/ |
| interrupts = <0 57 1 |
| 0 3 1>; |
| interrupt-names = "hdmitx_hpd", "viu1_vsync"; |
| /* 0:M8B 1:GXBB 2:GXTVBB 3:GXL 4:GXM |
| * 5:TXL 6:TXLX 7:AXG 8:GXLX 9:TXHD |
| * 10:G12A 11:G12B |
| */ |
| ic_type = <11>; |
| vend_data: vend_data{ /* Should modified by Customer */ |
| vendor_name = "Amlogic"; /* Max Chars: 8 */ |
| product_desc = "MBox Meson Ref"; /* Max Chars: 16 */ |
| /* standards.ieee.org/develop/regauth/oui/oui.txt */ |
| vendor_id = <0x000000>; |
| }; |
| }; |
| |
| galcore { |
| compatible = "amlogic, galcore"; |
| dev_name = "galcore"; |
| status = "disabled"; |
| clocks = <&clkc CLKID_VNANOQ_AXI_CLK_COMP>, |
| <&clkc CLKID_VNANOQ_CORE_CLK_COMP>; |
| clock-names = "cts_vipnanoq_axi_clk_composite", |
| "cts_vipnanoq_core_clk_composite"; |
| interrupts = <0 147 4>; |
| interrupt-names = "galcore"; |
| reg = <0xff100000 0x800 |
| 0xff000000 0x400000 |
| 0xff63c10c 0x4 |
| 0xff63c110 0x4 |
| 0xffd01088 0x4 |
| 0xff63c1c8 0x4 |
| >; |
| reg-names = "NN_REG","NN_SRAM","NN_MEM0", |
| "NN_MEM1","NN_RESET","NN_CLK"; |
| nn_power_version = <2>; |
| nn_efuse = <0xff63003c 0x20>; |
| }; |
| |
| aocec: aocec { |
| compatible = "amlogic, aocec-g12a"; |
| device_name = "aocec"; |
| status = "okay"; |
| vendor_name = "Amlogic"; /* Max Chars: 8 */ |
| /* Refer to the following URL at: |
| * http://standards.ieee.org/develop/regauth/oui/oui.txt |
| */ |
| vendor_id = <0x000000>; |
| product_desc = "G12B"; /* Max Chars: 16 */ |
| cec_osd_string = "AML_MBOX"; /* Max Chars: 14 */ |
| port_num = <1>; |
| output = <1>; |
| ee_cec; |
| arc_port_mask = <0x2>; |
| interrupts = <0 203 1 |
| 0 199 1>; /*0:snps 1:ts*/ |
| interrupt-names = "hdmi_aocecb","hdmi_aocec"; |
| pinctrl-names = "default","hdmitx_aocecb","cec_pin_sleep"; |
| pinctrl-0=<&eecec_a>; |
| pinctrl-1=<&eecec_b>; |
| pinctrl-2=<&eecec_b>; |
| reg = <0xFF80023c 0x4 |
| 0xFF800000 0x400 |
| 0xFF634400 0x26>; |
| reg-names = "ao_exit","ao","periphs"; |
| }; |
| |
| /*if you want to use vdin just modify status to "ok"*/ |
| vdin0: vdin0 { |
| compatible = "amlogic, vdin"; |
| dev_name = "vdin0"; |
| status = "disabled"; |
| reserve-iomap = "true"; |
| flag_cma = <0>;/*1:share with codec_mm;2:cma alone*/ |
| /*MByte, if 10bit disable: 64M(YUV422), |
| *if 10bit enable: 64*1.5 = 96M(YUV422) |
| *if support 4K2K-YUV444-10bit-WR:3840*2160*4*4 ~= 128M |
| *if support 4K2K-YUV422-10bit-wr:3840*2160*3*4 ~= 96M |
| *if support 4K2K-YUV422-8BIT-WR:3840*2160*2*4 ~= 64M |
| *if support 1080p-YUV422-8BIT-WR:1920*1080*2*4 ~= 16M |
| */ |
| /*cma_size = <16>;*/ |
| interrupts = <0 83 1>; |
| rdma-irq = <2>; |
| /*clocks = <&clock CLK_FPLL_DIV5>, |
| * <&clock CLK_VDIN_MEAS_CLK>; |
| *clock-names = "fclk_div5", "cts_vdin_meas_clk"; |
| */ |
| vdin_id = <0>; |
| }; |
| vdin1: vdin1 { |
| compatible = "amlogic, vdin"; |
| dev_name = "vdin1"; |
| status = "disabled"; |
| reserve-iomap = "true"; |
| flag_cma = <0>;/*1:share with codec_mm;0:cma alone*/ |
| interrupts = <0 85 1>; |
| rdma-irq = <4>; |
| /*clocks = <&clock CLK_FPLL_DIV5>, |
| * <&clock CLK_VDIN_MEAS_CLK>; |
| *clock-names = "fclk_div5", "cts_vdin_meas_clk"; |
| */ |
| vdin_id = <1>; |
| }; |
| |
| vout { |
| compatible = "amlogic, vout"; |
| dev_name = "vout"; |
| status = "okay"; |
| }; |
| |
| vout2 { |
| compatible = "amlogic, vout2"; |
| dev_name = "vout"; |
| status = "okay"; |
| clocks = <&clkc CLKID_VPU_CLKC_P0_COMP>, |
| <&clkc CLKID_VPU_CLKC_MUX>; |
| clock-names = "vpu_clkc0", |
| "vpu_clkc"; |
| }; |
| |
| dummy_venc: dummy_venc { |
| compatible = "amlogic, dummy_venc"; |
| status = "okay"; |
| clocks = <&clkc CLKID_VCLK2_ENCP |
| &clkc CLKID_VCLK2_VENCP0 |
| &clkc CLKID_VCLK2_VENCP1 |
| &clkc CLKID_VCLK2_ENCI |
| &clkc CLKID_VCLK2_VENCI0 |
| &clkc CLKID_VCLK2_VENCI1 |
| &clkc CLKID_VCLK2_ENCL |
| &clkc CLKID_VCLK2_VENCL>; |
| clock-names = "encp_top_gate", |
| "encp_int_gate0", |
| "encp_int_gate1", |
| "venci_top_gate", |
| "enci_int_gate0", |
| "enci_int_gate1", |
| "encl_top_gate", |
| "encl_int_gate"; |
| }; |
| |
| vdac { |
| compatible = "amlogic, vdac-g12b"; |
| status = "okay"; |
| }; |
| |
| canvas: canvas{ |
| compatible = "amlogic, meson, canvas"; |
| dev_name = "amlogic-canvas"; |
| status = "okay"; |
| reg = <0xff638000 0x2000>; |
| }; |
| |
| ge2d { |
| compatible = "amlogic, ge2d-g12a"; |
| dev_name = "ge2d"; |
| status = "okay"; |
| interrupts = <0 146 1>; |
| interrupt-names = "ge2d"; |
| clocks = <&clkc CLKID_VAPB_MUX>, |
| <&clkc CLKID_G2D>, |
| <&clkc CLKID_GE2D_GATE>; |
| clock-names = "clk_vapb_0", |
| "clk_ge2d", |
| "clk_ge2d_gate"; |
| reg = <0xff940000 0x10000>; |
| }; |
| |
| meson-amvideom { |
| compatible = "amlogic, amvideom"; |
| dev_name = "amvideom"; |
| status = "okay"; |
| interrupts = <0 3 1>; |
| interrupt-names = "vsync"; |
| }; |
| |
| codec_io: codec_io { |
| compatible = "amlogic, codec_io"; |
| status = "okay"; |
| #address-cells=<1>; |
| #size-cells=<1>; |
| ranges; |
| io_cbus_base{ |
| reg = <0xffd00000 0x100000>; |
| }; |
| io_dos_base{ |
| reg = <0xff620000 0x10000>; |
| }; |
| io_hiubus_base{ |
| reg = <0xff63c000 0x2000>; |
| }; |
| io_aobus_base{ |
| reg = <0xff800000 0x10000>; |
| }; |
| io_vcbus_base{ |
| reg = <0xff900000 0x40000>; |
| }; |
| io_dmc_base{ |
| reg = <0xff638000 0x2000>; |
| }; |
| io_efuse_base{ |
| reg = <0xff630000 0x2000>; |
| }; |
| }; |
| |
| gdc:gdc { |
| #address-cells=<1>; |
| #size-cells=<1>; |
| status = "ok"; |
| compatible = "amlogic, g12b-gdc"; |
| reg = <0xFF950000 0x0000100 |
| 0xFF63C16C 0x0000004 |
| 0xFF63C100 0x0000004>; |
| interrupts = <0 144 1>; |
| interrupt-names = "GDC"; |
| clocks = <&clkc CLKID_GDC_CORE_CLK_COMP |
| &clkc CLKID_GDC_AXI_CLK_COMP >; |
| clock-names = "core","axi"; |
| }; |
| |
| mesonstream { |
| compatible = "amlogic, codec, streambuf"; |
| dev_name = "mesonstream"; |
| status = "okay"; |
| clocks = <&clkc CLKID_DOS_PARSER |
| &clkc CLKID_DEMUX |
| &clkc CLKID_AHB_ARB0 |
| &clkc CLKID_DOS |
| &clkc CLKID_VDEC_MUX |
| &clkc CLKID_HCODEC_MUX |
| &clkc CLKID_HEVC_MUX |
| &clkc CLKID_HEVCF_MUX>; |
| clock-names = "parser_top", |
| "demux", |
| "ahbarb0", |
| "vdec", |
| "clk_vdec_mux", |
| "clk_hcodec_mux", |
| "clk_hevc_mux", |
| "clk_hevcb_mux"; |
| }; |
| |
| vdec { |
| compatible = "amlogic, vdec"; |
| dev_name = "vdec.0"; |
| status = "okay"; |
| interrupts = <0 3 1 |
| 0 23 1 |
| 0 32 1 |
| 0 43 1 |
| 0 44 1 |
| 0 45 1>; |
| interrupt-names = "vsync", |
| "demux", |
| "parser", |
| "mailbox_0", |
| "mailbox_1", |
| "mailbox_2"; |
| }; |
| |
| amvenc_avc{ |
| compatible = "amlogic, amvenc_avc"; |
| dev_name = "amvenc_avc"; |
| status = "okay"; |
| interrupts = <0 45 1>; |
| interrupt-names = "mailbox_2"; |
| }; |
| |
| hevc_enc{ |
| compatible = "cnm, HevcEnc"; |
| //memory-region = <&hevc_enc_reserved>; |
| dev_name = "HevcEnc"; |
| status = "okay"; |
| interrupts = <0 187 1>; |
| interrupt-names = "wave420l_irq"; |
| #address-cells=<1>; |
| #size-cells=<1>; |
| ranges; |
| io_reg_base{ |
| reg = <0xff610000 0x4000>; |
| }; |
| }; |
| |
| rdma{ |
| compatible = "amlogic, meson, rdma"; |
| dev_name = "amlogic-rdma"; |
| status = "okay"; |
| interrupts = <0 89 1>; |
| interrupt-names = "rdma"; |
| }; |
| |
| meson_fb: meson-fb { |
| compatible = "amlogic, meson-g12b"; |
| memory-region = <&logo_reserved>; |
| dev_name = "meson-fb"; |
| status = "disable"; |
| interrupts = <0 3 1 |
| 0 56 1 |
| 0 89 1>; |
| interrupt-names = "viu-vsync", "viu2-vsync", "rdma"; |
| /* uboot logo,fb0/fb1 memory size,if afbcd fb0=0x01851000*/ |
| display_mode_default = "1080p60hz"; |
| scale_mode = <1>; |
| /** 0:VPU free scale 1:OSD free scale 2:OSD super scale */ |
| display_size_default = <1920 1080 1920 2160 32>; |
| /*1920*1080*4*3 = 0x17BB000*/ |
| clocks = <&clkc CLKID_VPU_CLKC_MUX>; |
| clock-names = "vpu_clkc"; |
| }; |
| irblaster: meson-irblaster { |
| compatible = "amlogic, meson_irblaster"; |
| reg = <0xff80014c 0x10>, |
| <0xff800040 0x4>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&irblaster_pins>; |
| interrupts = <0 198 1>; |
| status = "disabled"; |
| }; |
| |
| sd_emmc_c: emmc@ffe07000 { |
| status = "disabled"; |
| compatible = "amlogic, meson-mmc-g12b-a"; |
| reg = <0xffe07000 0x800>; |
| interrupts = <0 191 1>; |
| pinctrl-names = "emmc_clk_cmd_pins", "emmc_all_pins"; |
| pinctrl-0 = <&emmc_clk_cmd_pins>; |
| pinctrl-1 = <&emmc_conf_pull_up &emmc_conf_pull_done>; |
| clocks = <&clkc CLKID_SD_EMMC_C>, |
| <&clkc CLKID_SD_EMMC_C_P0_COMP>, |
| <&clkc CLKID_FCLK_DIV2>, |
| <&clkc CLKID_FCLK_DIV5>, |
| <&xtal>; |
| clock-names = "core", "clkin0", "clkin1", "clkin2", "xtal"; |
| |
| bus-width = <8>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| /* mmc-ddr-1_8v; */ |
| /* mmc-hs200-1_8v; */ |
| |
| max-frequency = <200000000>; |
| non-removable; |
| disable-wp; |
| emmc { |
| pinname = "emmc"; |
| ocr_avail = <0x200080>; /**VDD voltage 3.3 ~ 3.4 */ |
| /*caps defined in dts*/ |
| tx_delay = <0>; |
| max_req_size = <0x20000>; /**128KB*/ |
| gpio_dat3 = <&gpio BOOT_3 GPIO_ACTIVE_HIGH>; |
| hw_reset = <&gpio BOOT_9 GPIO_ACTIVE_HIGH>; |
| card_type = <1>; |
| /* 1:mmc card(include eMMC), |
| * 2:sd card(include tSD) |
| */ |
| }; |
| }; |
| |
| sd_emmc_b:sd@ffe05000 { |
| status = "disabled"; |
| compatible = "amlogic, meson-mmc-g12b"; |
| reg = <0xffe05000 0x800>; |
| interrupts = <0 190 1>; |
| |
| pinctrl-names = "sd_all_pins", |
| "sd_clk_cmd_pins", |
| "sd_1bit_pins", |
| "sd_clk_cmd_uart_pins", |
| "sd_1bit_uart_pins", |
| "sd_to_ao_uart_pins", |
| "ao_to_sd_uart_pins", |
| "sd_to_ao_jtag_pins", |
| "ao_to_sd_jtag_pins"; |
| pinctrl-0 = <&sd_all_pins>; |
| pinctrl-1 = <&sd_clk_cmd_pins>; |
| pinctrl-2 = <&sd_1bit_pins>; |
| pinctrl-3 = <&sd_to_ao_uart_clr_pins |
| &sd_clk_cmd_pins &ao_to_sd_uart_pins>; |
| pinctrl-4 = <&sd_to_ao_uart_clr_pins |
| &sd_1bit_pins &ao_to_sd_uart_pins>; |
| pinctrl-5 = <&sd_all_pins &sd_to_ao_uart_pins>; |
| pinctrl-6 = <&sd_to_ao_uart_clr_pins &ao_to_sd_uart_pins>; |
| pinctrl-7 = <&sd_all_pins &sd_to_ao_uart_pins>; |
| pinctrl-8 = <&sd_to_ao_uart_clr_pins &ao_to_sd_uart_pins>; |
| |
| clocks = <&clkc CLKID_SD_EMMC_B>, |
| <&clkc CLKID_SD_EMMC_B_P0_COMP>, |
| <&clkc CLKID_FCLK_DIV2>, |
| <&clkc CLKID_FCLK_DIV5>, |
| <&xtal>; |
| clock-names = "core", "clkin0", "clkin1", "clkin2", "xtal"; |
| |
| bus-width = <4>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| max-frequency = <100000000>; |
| disable-wp; |
| sd { |
| pinname = "sd"; |
| ocr_avail = <0x200080>; /**VDD voltage 3.3 ~ 3.4 */ |
| max_req_size = <0x20000>; /**128KB*/ |
| gpio_dat3 = <&gpio GPIOC_3 GPIO_ACTIVE_HIGH>; |
| jtag_pin = <&gpio GPIOC_0 GPIO_ACTIVE_HIGH>; |
| gpio_cd = <&gpio GPIOC_6 GPIO_ACTIVE_HIGH>; |
| card_type = <5>; |
| /* 3:sdio device(ie:sdio-wifi), |
| * 4:SD combo (IO+mem) card |
| */ |
| }; |
| }; |
| |
| sd_emmc_a:sdio@ffe03000 { |
| status = "disabled"; |
| compatible = "amlogic, meson-mmc-g12b"; |
| reg = <0xffe03000 0x800>; |
| interrupts = <0 189 4>; |
| |
| pinctrl-names = "sdio_all_pins", |
| "sdio_clk_cmd_pins"; |
| pinctrl-0 = <&sdio_all_pins>; |
| pinctrl-1 = <&sdio_clk_cmd_pins>; |
| |
| clocks = <&clkc CLKID_SD_EMMC_A>, |
| <&clkc CLKID_SD_EMMC_A_P0_COMP>, |
| <&clkc CLKID_FCLK_DIV2>, |
| <&clkc CLKID_FCLK_DIV5>, |
| <&xtal>; |
| clock-names = "core", "clkin0", "clkin1", "clkin2", "xtal"; |
| |
| bus-width = <4>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| max-frequency = <100000000>; |
| disable-wp; |
| sdio { |
| pinname = "sdio"; |
| ocr_avail = <0x200080>; /**VDD voltage 3.3 ~ 3.4 */ |
| max_req_size = <0x20000>; /**128KB*/ |
| card_type = <3>; |
| /* 3:sdio device(ie:sdio-wifi), |
| * 4:SD combo (IO+mem) card |
| */ |
| }; |
| }; |
| |
| nand: nfc@0 { |
| compatible = "amlogic, aml_mtd_nand"; |
| dev_name = "mtdnand"; |
| status = "disabled"; |
| reg = <0xFFE07800 0x200>; |
| interrupts = <0 34 1>; |
| |
| pinctrl-names = "nand_rb_mod","nand_norb_mod", "nand_cs_only"; |
| pinctrl-0 = <&all_nand_pins>; |
| pinctrl-1 = <&all_nand_pins>; |
| pinctrl-2 = <&nand_cs_pins>; |
| clocks = <&clkc CLKID_SD_EMMC_C>, |
| <&clkc CLKID_SD_EMMC_C_P0_COMP>; |
| clock-names = "core", "clkin"; |
| |
| device_id = <0>; |
| /*fip/tpl configurations, must be same |
| * with uboot if bl_mode was set as 1 |
| * bl_mode: 0 compact mode; 1 descrete mode |
| * if bl_mode was set as 1, fip configuration will work |
| */ |
| bl_mode = <1>; |
| /*copy count of fip*/ |
| fip_copies = <4>; |
| /*size of each fip copy */ |
| fip_size = <0x200000>; |
| nand_clk_ctrl = <0xFFE07000>; |
| /*partions defined in dts */ |
| }; |
| |
| meson_cooldev: meson-cooldev@0 { |
| status = "okay"; |
| compatible = "amlogic, meson-cooldev"; |
| device_name = "mcooldev"; |
| cooling_devices { |
| cpufreq_cool_cluster0 { |
| min_state = <1000000>; |
| dyn_coeff = <120>; |
| cluster_id = <0>; |
| gpu_pp = <2>; |
| node_name = "cpufreq_cool0"; |
| device_type = "cpufreq"; |
| }; |
| cpufreq_cool_cluster1 { |
| min_state = <1000000>; |
| dyn_coeff = <460>; |
| cluster_id = <1>; |
| gpu_pp = <2>; |
| node_name = "cpufreq_cool1"; |
| device_type = "cpufreq"; |
| }; |
| cpucore_cool_cluster { |
| min_state = <1>; |
| dyn_coeff = <0>; |
| gpu_pp = <2>; |
| node_name = "cpucore_cool"; |
| device_type = "cpucore"; |
| }; |
| gpufreq_cool { |
| min_state = <400>; |
| dyn_coeff = <358>; |
| cluster_id = <0>; |
| gpu_pp = <2>; |
| node_name = "gpufreq_cool0"; |
| device_type = "gpufreq"; |
| }; |
| gpucore_cool { |
| min_state = <1>; |
| dyn_coeff = <0>; |
| cluster_id = <0>; |
| gpu_pp = <2>; |
| node_name = "gpucore_cool0"; |
| device_type = "gpucore"; |
| }; |
| }; |
| cpufreq_cool0:cpufreq_cool0 { |
| #cooling-cells = <2>; /* min followed by max */ |
| }; |
| cpufreq_cool1:cpufreq_cool1 { |
| #cooling-cells = <2>; /* min followed by max */ |
| }; |
| cpucore_cool:cpucore_cool { |
| #cooling-cells = <2>; /* min followed by max */ |
| }; |
| gpufreq_cool0:gpufreq_cool0 { |
| #cooling-cells = <2>; /* min followed by max */ |
| }; |
| gpucore_cool0:gpucore_cool0 { |
| #cooling-cells = <2>; /* min followed by max */ |
| }; |
| }; |
| /*meson cooling devices end*/ |
| |
| thermal-zones { |
| soc_thermal: soc_thermal { |
| polling-delay = <1000>; |
| polling-delay-passive = <100>; |
| sustainable-power = <3550>; |
| thermal-sensors = <&p_tsensor 0>; |
| trips { |
| pswitch_on: trip-point@0 { |
| temperature = <60000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| pcontrol: trip-point@1 { |
| temperature = <75000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| phot: trip-point@2 { |
| temperature = <85000>; |
| hysteresis = <5000>; |
| type = "hot"; |
| }; |
| pcritical: trip-point@3 { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| cpufreq_cooling_map0 { |
| trip = <&pcontrol>; |
| cooling-device = <&cpufreq_cool0 0 10>; |
| contribution = <1024>; |
| }; |
| cpufreq_cooling_map1 { |
| trip = <&pcontrol>; |
| cooling-device = <&cpufreq_cool1 0 9>; |
| contribution = <1024>; |
| }; |
| cpucore_cooling_map { |
| trip = <&pcontrol>; |
| cooling-device = <&cpucore_cool 0 5>; |
| contribution = <1024>; |
| }; |
| gpufreq_cooling_map { |
| trip = <&pcontrol>; |
| cooling-device = <&gpufreq_cool0 0 4>; |
| contribution = <1024>; |
| }; |
| gpucore_cooling_map { |
| trip = <&pcontrol>; |
| cooling-device = <&gpucore_cool0 0 2>; |
| contribution = <1024>; |
| }; |
| }; |
| }; |
| ddr_thermal: ddr_thermal { |
| polling-delay = <1000>; |
| polling-delay-passive = <100>; |
| sustainable-power = <3550>; |
| thermal-sensors = <&d_tsensor 1>; |
| trips { |
| dswitch_on: trip-point@0 { |
| temperature = <60000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| dcontrol: trip-point@1 { |
| temperature = <75000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| dhot: trip-point@2 { |
| temperature = <85000>; |
| hysteresis = <5000>; |
| type = "hot"; |
| }; |
| dcritical: trip-point@3 { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| }; |
| }; |
| /*thermal zone end*/ |
| |
| /* Sound iomap */ |
| aml_snd_iomap { |
| compatible = "amlogic, snd-iomap"; |
| status = "okay"; |
| #address-cells=<1>; |
| #size-cells=<1>; |
| ranges; |
| pdm_bus { |
| reg = <0xFF640000 0x2000>; |
| }; |
| audiobus_base { |
| reg = <0xFF642000 0x2000>; |
| }; |
| audiolocker_base { |
| reg = <0xFF64A000 0x2000>; |
| }; |
| eqdrc_base { |
| reg = <0xFF656000 0x1800>; |
| }; |
| reset_base { |
| reg = <0xFFD01000 0x1000>; |
| }; |
| }; |
| |
| vddcpu0: pwmao_d-regulator { |
| compatible = "pwm-regulator"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm_ao_d_pins3>; |
| pwms = <&pwm_AO_cd MESON_PWM_1 1250 0>; |
| regulator-name = "vddcpu0"; |
| regulator-min-microvolt = <721000>; |
| regulator-max-microvolt = <1022000>; |
| regulator-always-on; |
| max-duty-cycle = <1250>; |
| /* Voltage Duty-Cycle */ |
| voltage-table = <1022000 0>, |
| <1011000 3>, |
| <1001000 6>, |
| <991000 10>, |
| <981000 13>, |
| <971000 16>, |
| <961000 20>, |
| <951000 23>, |
| <941000 26>, |
| <931000 30>, |
| <921000 33>, |
| <911000 36>, |
| <901000 40>, |
| <891000 43>, |
| <881000 46>, |
| <871000 50>, |
| <861000 53>, |
| <851000 56>, |
| <841000 60>, |
| <831000 63>, |
| <821000 67>, |
| <811000 70>, |
| <801000 73>, |
| <791000 76>, |
| <781000 80>, |
| <771000 83>, |
| <761000 86>, |
| <751000 90>, |
| <741000 93>, |
| <731000 96>, |
| <721000 100>; |
| status = "okay"; |
| }; |
| |
| vddcpu1: pwmab_a-regulator { |
| compatible = "pwm-regulator"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm_a_e2>; |
| pwms = <&pwm_ab MESON_PWM_0 1250 0>; |
| regulator-name = "vddcpu1"; |
| regulator-min-microvolt = <721000>; |
| regulator-max-microvolt = <1022000>; |
| regulator-always-on; |
| max-duty-cycle = <1250>; |
| /* Voltage Duty-Cycle */ |
| voltage-table = <1022000 0>, |
| <1011000 3>, |
| <1001000 6>, |
| <991000 10>, |
| <981000 13>, |
| <971000 16>, |
| <961000 20>, |
| <951000 23>, |
| <941000 26>, |
| <931000 30>, |
| <921000 33>, |
| <911000 36>, |
| <901000 40>, |
| <891000 43>, |
| <881000 46>, |
| <871000 50>, |
| <861000 53>, |
| <851000 56>, |
| <841000 60>, |
| <831000 63>, |
| <821000 67>, |
| <811000 70>, |
| <801000 73>, |
| <791000 76>, |
| <781000 80>, |
| <771000 83>, |
| <761000 86>, |
| <751000 90>, |
| <741000 93>, |
| <731000 96>, |
| <721000 100>; |
| status = "okay"; |
| }; |
| |
| rng { |
| compatible = "amlogic,meson-rng"; |
| status = "okay"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0xff630218 0x4>; |
| quality = /bits/ 16 <1000>; |
| }; |
| |
| ddr_bandwidth { |
| compatible = "amlogic, ddr-bandwidth"; |
| status = "okay"; |
| reg = <0xff638000 0x100 |
| 0xff638c00 0x100>; |
| interrupts = <0 52 1>; |
| interrupt-names = "ddr_bandwidth"; |
| }; |
| dmc_monitor { |
| compatible = "amlogic, dmc_monitor"; |
| status = "okay"; |
| reg_base = <0xff639000>; |
| interrupts = <0 51 1>; |
| }; |
| |
| isp_sc: isp-sc@ff655400 { |
| compatible = "amlogic, isp-sc"; |
| reg = <0xff655400 0x00001000>; |
| reg-names = "isp_sc"; |
| interrupts = <0 17 0>; |
| interrupt-names = "isp_sc"; |
| }; |
| |
| isp: isp@ff140000 { |
| compatible = "arm, isp"; |
| reg = <0xff140000 0x00040000>; |
| reg-names = "ISP"; |
| isp-efuse = <0xff630038 0x4000>; |
| interrupts = <0 142 4>; |
| interrupt-names = "ISP"; |
| temper-buf-size = <24>; |
| clocks = <&clkc CLKID_MIPI_ISP_CLK_COMP>, |
| <&clkc CLKID_MIPI_CSI_PHY_CLK0_COMP>; |
| clock-names = "cts_mipi_isp_clk_composite", |
| "cts_mipi_csi_phy_clk0_composite"; |
| link-device = <&isp_sc>; |
| }; |
| |
| adapter: isp-adapter@ff650000 { |
| compatible = "amlogic, isp-adapter"; |
| reg = <0xff650000 0x00006000>; |
| reg-names = "adapter"; |
| interrupts = <0 179 0>; |
| interrupt-names = "adapter-irq"; |
| }; |
| |
| phycsi: phy-csi@ff650000 { |
| compatible = "amlogic, phy-csi"; |
| reg = <0xff650000 0x00002000>, |
| <0xff652000 0x00002000>, |
| <0xff63c300 0x00000100>, |
| <0xff654000 0x00000100>, |
| <0xff654400 0x00000100>; |
| reg-names = "csi2_phy0", "csi2_phy1", "aphy_reg", |
| "csi0_host", "csi1_host"; |
| interrupts = <0 41 0>, |
| <0 42 0>, |
| <0 72 0>, |
| <0 74 0>, |
| <0 87 0>, |
| <0 88 0>; |
| interrupt-names = "phy0-irq", |
| "phy1-irq", |
| "csi-host0-intr2", |
| "csi-host0-intr1", |
| "csi-host1-intr2", |
| "csi-host1-intr1"; |
| link-device = <&adapter>; |
| }; |
| |
| defendkey: defendkey { |
| compatible = "amlogic, defendkey"; |
| reg = <0xff630218 0x4>; /*RNG_USR_DATA*/ |
| mem_size = <0 0x100000>; |
| status = "okay"; |
| }; |
| };/* end of / */ |
| |
| &pinctrl_aobus { |
| ao_uart_pins:ao_uart { |
| mux { |
| groups = "uart_ao_tx_a", |
| "uart_ao_rx_a"; |
| function = "uart_ao_a"; |
| }; |
| }; |
| |
| ao_b_uart_pins:ao_b_uart { |
| mux { |
| groups = "uart_ao_tx_b_2", |
| "uart_ao_rx_b_3"; |
| function = "uart_ao_b"; |
| }; |
| }; |
| |
| ao_i2c_master_pins1:ao_i2c_pins1 { |
| mux { |
| groups = "i2c_ao_sck", |
| "i2c_ao_sda"; |
| function = "i2c_ao"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| ao_i2c_master_pins2:ao_i2c_pins2 { |
| mux { |
| groups = "i2c_ao_sck_e", |
| "i2c_ao_sda_e"; |
| function = "i2c_ao"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| ao_i2c_slave_pins:ao_i2c_slave_pins { |
| mux { |
| groups = "i2c_ao_slave_sck", |
| "i2c_ao_slave_sda"; |
| function = "i2c_ao_slave"; |
| }; |
| }; |
| |
| pwm_ao_a_pins: pwm_ao_a { |
| mux { |
| groups = "pwm_ao_a"; |
| function = "pwm_ao_a"; |
| }; |
| }; |
| |
| pwm_ao_a_hiz_pins: pwm_ao_a_hiz { |
| mux { |
| groups = "pwm_ao_a_hiz"; |
| function = "pwm_ao_a"; |
| }; |
| }; |
| |
| pwm_ao_b_pins: pwm_ao_b { |
| mux { |
| groups = "pwm_ao_b"; |
| function = "pwm_ao_b"; |
| }; |
| }; |
| |
| pwm_ao_c_pins1: pwm_ao_c_pins1 { |
| mux { |
| groups = "pwm_ao_c_4"; |
| function = "pwm_ao_c"; |
| }; |
| }; |
| |
| pwm_ao_c_pins2: pwm_ao_c_pins2 { |
| mux { |
| groups = "pwm_ao_c_6"; |
| function = "pwm_ao_c"; |
| }; |
| }; |
| |
| pwm_ao_c_hiz_pins: pwm_ao_c_hiz { |
| mux { |
| groups = "pwm_ao_c_hiz_4"; |
| function = "pwm_ao_c"; |
| }; |
| }; |
| |
| pwm_ao_d_pins1: pwm_ao_d_pins1 { |
| mux { |
| groups = "pwm_ao_d_5"; |
| function = "pwm_ao_d"; |
| }; |
| }; |
| |
| pwm_ao_d_pins2: pwm_ao_d_pins2 { |
| mux { |
| groups = "pwm_ao_d_10"; |
| function = "pwm_ao_d"; |
| }; |
| }; |
| |
| pwm_ao_d_pins3: pwm_ao_d_pins3 { |
| mux { |
| groups = "pwm_ao_d_e"; |
| function = "pwm_ao_d"; |
| }; |
| }; |
| |
| aocec_a: ao_ceca { |
| mux { |
| groups = "cec_ao_a"; |
| function = "cec_ao"; |
| }; |
| }; |
| |
| aocec_b: ao_cecb { |
| mux { |
| groups = "cec_ao_b"; |
| function = "cec_ao"; |
| }; |
| }; |
| pwm_a_e2: pwm_a_e2 { |
| mux { |
| groups = "pwm_a_e2"; |
| function = "pwm_a_gpioe"; |
| }; |
| }; |
| |
| jtag_apao_pins:jtag_apao_pin { |
| mux { |
| groups = "jtag_a_tdi", |
| "jtag_a_tdo", |
| "jtag_a_clk", |
| "jtag_a_tms"; |
| function = "jtag_a"; |
| }; |
| }; |
| }; |
| |
| &pinctrl_periphs { |
| /* sdemmc portC */ |
| emmc_clk_cmd_pins:emmc_clk_cmd_pins { |
| mux { |
| groups = "emmc_clk", |
| "emmc_cmd"; |
| function = "emmc"; |
| input-enable; |
| bias-pull-up; |
| drive-strength = <3>; |
| }; |
| }; |
| |
| emmc_conf_pull_up:emmc_conf_pull_up { |
| mux { |
| groups = "emmc_nand_d7", |
| "emmc_nand_d6", |
| "emmc_nand_d5", |
| "emmc_nand_d4", |
| "emmc_nand_d3", |
| "emmc_nand_d2", |
| "emmc_nand_d1", |
| "emmc_nand_d0", |
| "emmc_clk", |
| "emmc_cmd"; |
| function = "emmc"; |
| input-enable; |
| bias-pull-up; |
| drive-strength = <3>; |
| }; |
| }; |
| |
| emmc_conf_pull_done:emmc_conf_pull_done { |
| mux { |
| groups = "emmc_nand_ds"; |
| function = "emmc"; |
| input-enable; |
| bias-pull-down; |
| drive-strength = <3>; |
| }; |
| }; |
| |
| /* sdemmc portB */ |
| sd_clk_cmd_pins:sd_clk_cmd_pins { |
| mux { |
| groups = "sdcard_cmd_c", |
| "sdcard_clk_c"; |
| function = "sdcard"; |
| input-enable; |
| bias-pull-up; |
| drive-strength = <3>; |
| }; |
| }; |
| |
| sd_all_pins:sd_all_pins { |
| mux { |
| groups = "sdcard_d0_c", |
| "sdcard_d1_c", |
| "sdcard_d2_c", |
| "sdcard_d3_c", |
| "sdcard_cmd_c", |
| "sdcard_clk_c"; |
| function = "sdcard"; |
| input-enable; |
| bias-pull-up; |
| drive-strength = <3>; |
| }; |
| }; |
| sd_1bit_pins:sd_1bit_pins { |
| mux { |
| groups = "sdcard_d0_c", |
| "sdcard_cmd_c", |
| "sdcard_clk_c"; |
| function = "sdcard"; |
| input-enable; |
| bias-pull-up; |
| drive-strength = <3>; |
| }; |
| }; |
| |
| ao_to_sd_uart_pins:ao_to_sd_uart_pins { |
| mux { |
| groups = "uart_ao_tx_a_c3", |
| "uart_ao_rx_a_c2"; |
| function = "uart_ao_a_ee"; |
| bias-pull-up; |
| input-enable; |
| }; |
| }; |
| /* sdemmc portA */ |
| sdio_clk_cmd_pins:sdio_clk_cmd_pins { |
| mux { |
| groups = "sdio_clk", |
| "sdio_cmd"; |
| function = "sdio"; |
| input-enable; |
| bias-pull-up; |
| drive-strength = <3>; |
| }; |
| }; |
| |
| sdio_all_pins:sdio_all_pins { |
| mux { |
| groups = "sdio_d0", |
| "sdio_d1", |
| "sdio_d2", |
| "sdio_d3", |
| "sdio_clk", |
| "sdio_cmd"; |
| function = "sdio"; |
| input-enable; |
| bias-pull-up; |
| drive-strength = <3>; |
| }; |
| }; |
| all_nand_pins: all_nand_pins { |
| mux { |
| groups = "emmc_nand_d0", |
| "emmc_nand_d1", |
| "emmc_nand_d2", |
| "emmc_nand_d3", |
| "emmc_nand_d4", |
| "emmc_nand_d5", |
| "emmc_nand_d6", |
| "emmc_nand_d7", |
| "nand_ce0", |
| "nand_ale", |
| "nand_cle", |
| "nand_wen_clk", |
| "nand_ren_wr", |
| "nand_rb0"; |
| function = "nand"; |
| input-enable; |
| }; |
| }; |
| |
| nand_cs_pins: nand_cs { |
| mux { |
| groups = "nand_ce0"; |
| function = "nand"; |
| }; |
| }; |
| |
| i2c0_master_pins1:i2c0_pins1 { |
| mux { |
| groups = "i2c0_sda_c", |
| "i2c0_sck_c"; |
| function = "i2c0"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| i2c0_master_pins2:i2c0_pins2 { |
| mux { |
| groups = "i2c0_sda_z0", |
| "i2c0_sck_z1"; |
| function = "i2c0"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| i2c0_master_pins3:i2c0_pins3 { |
| mux { |
| groups = "i2c0_sda_z7", |
| "i2c0_sck_z8"; |
| function = "i2c0"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| i2c1_master_pins1:i2c1_pins1 { |
| mux { |
| groups = "i2c1_sda_x", |
| "i2c1_sck_x"; |
| function = "i2c1"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| i2c1_master_pins2:i2c1_pins2 { |
| mux { |
| groups = "i2c1_sda_h2", |
| "i2c1_sck_h3"; |
| function = "i2c1"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| i2c1_master_pins3:i2c1_pins3 { |
| mux { |
| groups = "i2c1_sda_h6", |
| "i2c1_sck_h7"; |
| function = "i2c1"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| i2c2_master_pins1:i2c2_pins1 { |
| mux { |
| groups = "i2c2_sda_x", |
| "i2c2_sck_x"; |
| function = "i2c2"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| i2c2_master_pins2:i2c2_pins2 { |
| mux { |
| groups = "i2c2_sda_z", |
| "i2c2_sck_z"; |
| function = "i2c2"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| i2c3_master_pins1:i2c3_pins1 { |
| mux { |
| groups = "i2c3_sda_h", |
| "i2c3_sck_h"; |
| function = "i2c3"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| i2c3_master_pins2:i2c3_pins2 { |
| mux { |
| groups = "i2c3_sda_a", |
| "i2c3_sck_a"; |
| function = "i2c3"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| pwm_a_pins: pwm_a { |
| mux { |
| groups = "pwm_a"; |
| function = "pwm_a"; |
| }; |
| }; |
| |
| pwm_b_pins1: pwm_b_pins1 { |
| mux { |
| groups = "pwm_b_x7"; |
| function = "pwm_b"; |
| }; |
| }; |
| |
| pwm_b_pins2: pwm_b_pins2 { |
| mux { |
| groups = "pwm_b_x19"; |
| function = "pwm_b"; |
| }; |
| }; |
| |
| pwm_b_pins3: pwm_b_pins3 { |
| mux { |
| groups = "pwm_b_h"; |
| function = "pwm_b"; |
| }; |
| }; |
| |
| pwm_b_pins4: pwm_b_pins4 { |
| mux { |
| groups = "pwm_b_z0"; |
| function = "pwm_b"; |
| }; |
| }; |
| |
| pwm_b_pins5: pwm_b_pins5 { |
| mux { |
| groups = "pwm_b_z13"; |
| function = "pwm_b"; |
| }; |
| }; |
| |
| pwm_c_pins1: pwm_c_pins1 { |
| mux { |
| groups = "pwm_c_c4"; |
| function = "pwm_c"; |
| }; |
| }; |
| |
| pwm_c_pins2: pwm_c_pins2 { |
| mux { |
| groups = "pwm_c_x5"; |
| function = "pwm_c"; |
| }; |
| }; |
| |
| pwm_c_pins3: pwm_c_pins3 { |
| mux { |
| groups = "pwm_c_x8"; |
| function = "pwm_c"; |
| }; |
| }; |
| |
| pwm_c_pins4: pwm_c_pins4 { |
| mux { |
| groups = "pwm_c_z"; |
| function = "pwm_c"; |
| }; |
| }; |
| |
| pwm_d_pins1: pwm_d_pins1 { |
| mux { |
| groups = "pwm_d_x3"; |
| function = "pwm_d"; |
| }; |
| }; |
| |
| pwm_d_pins2: pwm_d_pins2 { |
| mux { |
| groups = "pwm_d_x6"; |
| function = "pwm_d"; |
| }; |
| }; |
| |
| pwm_d_pins3: pwm_d_pins3 { |
| mux { |
| groups = "pwm_d_z"; |
| function = "pwm_d"; |
| }; |
| }; |
| |
| pwm_d_pins4: pwm_d_pins4 { |
| mux { |
| groups = "pwm_d_a4"; |
| function = "pwm_d"; |
| }; |
| }; |
| |
| pwm_e_pins: pwm_e { |
| mux { |
| groups = "pwm_e"; |
| function = "pwm_e"; |
| }; |
| }; |
| |
| pwm_f_pins1: pwm_f_pins1 { |
| mux { |
| groups = "pwm_f_x"; |
| function = "pwm_f"; |
| }; |
| }; |
| |
| pwm_f_pins2: pwm_f_pins2 { |
| mux { |
| groups = "pwm_f_h"; |
| function = "pwm_f"; |
| }; |
| }; |
| |
| pwm_f_pins3: pwm_f_pins3 { |
| mux { |
| groups = "pwm_f_z"; |
| function = "pwm_f"; |
| }; |
| }; |
| |
| pwm_f_pins4: pwm_f_pins4 { |
| mux { |
| groups = "pwm_f_a11"; |
| function = "pwm_f"; |
| }; |
| }; |
| |
| spicc0_pins_x: spicc0_pins_x { |
| mux { |
| groups = "spi0_mosi_x", |
| "spi0_miso_x", |
| //"spi0_ss0_x", |
| "spi0_clk_x"; |
| function = "spi0"; |
| drive-strength = <1>; |
| }; |
| }; |
| |
| spicc1_pins: spicc1_pins { |
| mux { |
| groups = "spi1_mosi", |
| "spi1_miso", |
| //"spi1_ss0", |
| "spi1_clk"; |
| function = "spi1"; |
| drive-strength = <1>; |
| }; |
| }; |
| |
| a_uart_pins:a_uart { |
| mux { |
| groups = "uart_tx_a", |
| "uart_rx_a", |
| "uart_cts_a", |
| "uart_rts_a"; |
| function = "uart_a"; |
| }; |
| }; |
| |
| b_uart_pins:b_uart { |
| mux { |
| groups = "uart_tx_b", |
| "uart_rx_b"; |
| function = "uart_b"; |
| }; |
| }; |
| |
| c_uart_pins:c_uart { |
| mux { |
| groups = "uart_tx_c", |
| "uart_rx_c"; |
| function = "uart_c"; |
| }; |
| }; |
| |
| hdmitx_hpd: hdmitx_hpd { |
| mux { |
| groups = "hdmitx_hpd_in"; |
| function = "hdmitx"; |
| bias-disable; |
| }; |
| }; |
| |
| hdmitx_hpd_gpio: hdmitx_hpd_gpio { |
| mux { |
| groups = "GPIOH_1"; |
| function = "gpio_periphs"; |
| bias-disable; |
| }; |
| }; |
| |
| hdmitx_ddc: hdmitx_ddc { |
| mux { |
| groups = "hdmitx_sda", |
| "hdmitx_sck"; |
| function = "hdmitx"; |
| bias-disable; |
| }; |
| }; |
| |
| eecec_a: ee_ceca { |
| mux { |
| groups = "cec_ao_a_ee"; |
| function = "cec_ao_ee"; |
| }; |
| }; |
| |
| eecec_b: ee_cecb { |
| mux { |
| groups = "cec_ao_b_ee"; |
| function = "cec_ao_ee"; |
| }; |
| }; |
| |
| internal_eth_pins: internal_eth_pins { |
| mux { |
| groups = "eth_link_led", |
| "eth_act_led"; |
| function = "eth"; |
| }; |
| }; |
| |
| external_eth_pins: external_eth_pins { |
| mux { |
| groups = "eth_mdio", |
| "eth_mdc", |
| "eth_rgmii_rx_clk", |
| "eth_rx_dv", |
| "eth_rxd0", |
| "eth_rxd1", |
| "eth_rxd2_rgmii", |
| "eth_rxd3_rgmii", |
| "eth_rgmii_tx_clk", |
| "eth_txen", |
| "eth_txd0", |
| "eth_txd1", |
| "eth_txd2_rgmii", |
| "eth_txd3_rgmii"; |
| function = "eth"; |
| drive-strength = <3>; |
| }; |
| }; |
| |
| irblaster_pins2:irblaster_pins2 { |
| mux { |
| groups = "remote_out_h"; |
| function = "remote_out"; |
| }; |
| }; |
| |
| irblaster_pins3:irblaster_pins3 { |
| mux { |
| groups = "remote_out_z"; |
| function = "remote_out"; |
| }; |
| }; |
| |
| jtag_apee_pins:jtag_apee_pin { |
| mux { |
| groups = "jtag_b_tdi", |
| "jtag_b_tdo", |
| "jtag_b_clk", |
| "jtag_b_tms"; |
| function = "jtag_b"; |
| }; |
| }; |
| }; |
| |
| &gpu{ |
| system-coherency = <0>; |
| tbl = <&dvfs285_cfg |
| &dvfs400_cfg |
| &dvfs500_cfg |
| &dvfs666_cfg |
| &dvfs800_cfg |
| &dvfs800_cfg>; |
| }; |
| |
| &pinctrl_aobus { |
| sd_to_ao_uart_clr_pins:sd_to_ao_uart_clr_pins { |
| mux { |
| groups = "GPIOAO_0", |
| "GPIOAO_1"; |
| function = "gpio_aobus"; |
| }; |
| }; |
| |
| sd_to_ao_uart_pins:sd_to_ao_uart_pins { |
| mux { |
| groups = "uart_ao_tx_a", |
| "uart_ao_rx_a"; |
| function = "uart_ao_a"; |
| bias-pull-up; |
| input-enable; |
| }; |
| }; |
| |
| remote_pins:remote_pin { |
| mux { |
| groups = "remote_input_ao"; |
| function = "remote_input_ao"; |
| }; |
| }; |
| |
| irblaster_pins:irblaster_pin { |
| mux { |
| groups = "remote_out_ao"; |
| function = "remote_out_ao"; |
| }; |
| }; |
| |
| irblaster_pins1:irblaster_pin1 { |
| mux { |
| groups = "remote_out_ao9"; |
| function = "remote_out_ao"; |
| }; |
| }; |
| }; /* end of pinctrl_aobus */ |