| # bt.cfg,now just parse '#' for annotation |
| SUPPORT_UNIFY_WOBLE 1 |
| # this item is valid only when SUPPORT_UNIFY_WOBLE enabled. 0: LEGACY, LOW or HIGH. 1: Waveform. 2: IR |
| UNIFY_WOBLE_TYPE 1 |
| SUPPORT_LEGACY_WOBLE 0 |
| SUPPORT_WOBLE_BY_EINT 0 |
| BT_DONGLE_RESET_GPIO_PIN 220 |
| SAVE_FW_DUMP_IN_KERNEL 0 |
| # this item is valid only when support save fw_dump in kernel |
| SYS_LOG_FILE_NAME /sdcard/bt_sys_log |
| # this item is valid only when support save fw_dump in kernel |
| FW_DUMP_FILE_NAME /sdcard/bt_fw_dump |
| SUPPORT_DONGLE_RESET 1 |
| SUPPORT_FULL_FW_DUMP 0 |
| SUPPORT_WOBLE_WAKELOCK 1 |
| SUPPORT_WOBLE_FOR_BT_DISABLE 1 |
| RESET_STACK_AFTER_WOBLE 1 |
| SUPPORT_BT_SINGLE_SKU 1 |
| |
| SUPPORT_BT_AUDIO_SETTING 1 |
| # this item is vaild only when SUPPORT_BT_AUDIO_SETTING = 1 |
| AUDIO_ENABLE_CMD: 0x49, 0x00, 0x80, 0x00, |
| # this item is vaild only when SUPPORT_BT_AUDIO_SETTING = 1. Only for Kiwi, set pinmux num & mode |
| AUDIO_PINMUX_NUM: 0x00, 0x01, 0x02, 0x04, |
| AUDIO_PINMUX_MODE: 0x01, 0x01, 0x01, 0x01, |
| |
| SUPPORT_PICUS_TO_HOST 0 |
| SUPPORT_AUTO_PICUS 0 |
| PICUS_ENABLE_COMMAND: 0x01, 0x5D, 0xFC, 0x04, 0x00, 0x00, 0x02, 0x02, |
| PICUS_FILTER_COMMAND: 0x5F, 0xFC, 0x2E, 0x50, 0x01, 0x0A, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0xE0, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x01, 0x01, 0x01, 0x00, 0x01, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| |
| WMT_CMD000: 0x6F, 0xFC, 0x06, 0x01, 0x06, 0x02, 0x00, 0x03, 0x01, |
| # phase1 means this wmt cmd should be send to FW after download patch or after BT power on |
| # this wmt cmd used to enable bus vio |
| PHASE1_WMT_CMD000: 0x6F, 0xFC, 0x08, 0x01, 0x02, 0x04, 0x00, 0x1D, 0x01, 0x00, 0x00, |
| #vendor cmd need to send to FW after BT power on |
| VENDOR_CMD000: 0x96, 0xFD, 0x18, 0x03, 0x03, 0x06, 0x0E, 0x03, 0x03, 0x07, 0x0E, 0x03, 0x03, 0x08, 0x0E, 0x03, 0x03, 0x0B, 0x11, 0x03, 0x03, 0x0D, 0x0C, 0x03, 0x03, 0x13, 0x10, |
