| ; |
| ; ************************ |
| ; * INIT_TS.TXT SCRIPT * |
| ; ************************ |
| ; |
| ; *** CLOSE INPUT *** |
| ; |
| IN_SEL 0x00 |
| ; |
| ; *** CLOSE OUPUT *** |
| ; |
| OUT_SEL 0x00 |
| ; |
| ; *** RESET FIFO *** |
| ; |
| FIFO_CTRL 0x0f |
| SYNC_RTV_CTRL 0x0f |
| ; |
| ; |
| ; ************************* |
| ; * INIT_USB.TXT SCRIPT * |
| ; ************************* |
| ; |
| ; *** Endpoint Config *** |
| ; |
| DMA_ACC_EPS 0x3f |
| EPS_ENABLE 0x7f |
| ; |
| ; *** FIFO Control *** |
| ; |
| USB2TS_CTRL 0x0f |
| TS2USB_CTRL 0x0f |
| ; |
| ; *** FREQ Control *** |
| ; |
| USB2TS0_RDL 0x80 |
| USB2TS1_RDL 0x80 |
| ; |
| ;----------------------------------------------------------------------------- |
| ; Set CAM power |
| ;----------------------------------------------------------------------------- |
| ; |
| GPIO0_DATA_OUT 0x00 |
| ; |
| ; unlock CFG |
| CFG_2 0x00 |
| ; |
| ; 1) DVB/CI/CI+/SCARD 2slot |
| CFG_1 0x00 |
| ; |
| ; 2) Set the Default "power off" state such as VCC_MODA=VCC_MODB=VPPx_MODA=VPPx_MODB='Z' |
| GPIO0_DFT 0x00 |
| ; |
| ; 3) Set GPIO3 as external power switch driver |
| GPIO0_MASK_DATA 0x07 |
| ; |
| ; 4) Set "power on" state (VCC=VPP1=VPP2= 5V) |
| GPIO0_DATA_OUT 0x01 |
| ; |
| ; 5) Lock config |
| CFG_2 0x01 |
| ; |
| ; 6) Write in the GPIO0_DIR_REG: defines the GPIOs, which |
| ; are used to drive the external power switch, in output mode. |
| GPIO0_DIR 0x07 |
| ; |
| ; 7) Check VCCENable |
| ?CFG_1 0x20 |
| ; |
| ; 8) Set & wait for PcmciaOutputEnable |
| |CFG_1 0x08 |
| ?CFG_1 0x08 |
| ; |
| ;--------------------------------------- |
| ; Set Router CAM |
| ;--------------------------------------- |
| ; |
| ; |
| GAP_REMOVER_CH0_CTRL 0x0C |
| GAP_REMOVER_CH1_CTRL 0x0C |
| |
| ; 9) CH0 & CH1 from CAM A & B, CAM A & B from CH0 & CH1 |
| ; |
| ROUTER_CAM_MOD 0x21 |
| ROUTER_CAM_CH 0x00 |
| ; |
| ;_Wait 200 |
| ;--------------------------------------- |
| ; ROUTER CAM |
| ;--------------------------------------- |
| OUT_SEL 0x03 |
| ; |
| USB2TS0_RDL 0x80 |
| USB2TS1_RDL 0x80 |
| ; |
| IN_SEL 0x22 |
| |
