| /* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ |
| /* |
| * Copyright (c) 2019 Amlogic, Inc. All rights reserved. |
| */ |
| |
| #ifndef __BOARD_CFG_H__ |
| #define __BOARD_CFG_H__ |
| |
| #include <asm/arch/cpu.h> |
| |
| /* |
| * platform power init config |
| */ |
| |
| #define AML_VCCK_INIT_VOLTAGE 939 //VCCK power up voltage |
| #define AML_VDDEE_INIT_VOLTAGE 810 // VDDEE power up voltage |
| |
| /* SMP Definitinos */ |
| #define CPU_RELEASE_ADDR secondary_boot_func |
| |
| /* Bootloader Control Block function |
| That is used for recovery and the bootloader to talk to each other |
| */ |
| #define CONFIG_BOOTLOADER_CONTROL_BLOCK |
| |
| /* Serial config */ |
| #define CONFIG_CONS_INDEX 2 |
| #define CONFIG_BAUDRATE 115200 |
| |
| /*if disable uboot console, enable it*/ |
| //#define CONFIG_SILENT_CONSOLE |
| #ifdef CONFIG_SILENT_CONSOLE |
| #undef CONFIG_SILENT_CONSOLE_UPDATE_ON_RELOC |
| #endif |
| |
| /* Enable ir remote wake up for bl30 */ |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL1 0xef10fe01 //amlogic tv ir --- power |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL2 0XBB44FB04 //amlogic tv ir --- ch+ |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL3 0xF20DFE01 //amlogic tv ir --- ch- |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL4 0XBA45BD02 //amlogic small ir--- power |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL5 0xe51afb04 |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL6 0xFFFFFFFF |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL7 0xFFFFFFFF |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL8 0xFFFFFFFF |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL9 0xFFFFFFFF |
| |
| /*config the default parameters for adc power key*/ |
| #define AML_ADC_POWER_KEY_CHAN 2 /*channel range: 0-7*/ |
| #define AML_ADC_POWER_KEY_VAL 0 /*sample value range: 0-1023*/ |
| |
| #ifdef CONFIG_DTB_BIND_KERNEL //load dtb from kernel, such as boot partition |
| #define CONFIG_DTB_LOAD "imgread dtb ${boot_part} ${dtb_mem_addr}" |
| #else |
| #define CONFIG_DTB_LOAD "imgread dtb _aml_dtb ${dtb_mem_addr}" |
| #endif//#ifdef CONFIG_DTB_BIND_KERNEL //load dtb from kernel, such as boot partition |
| |
| /* args/envs */ |
| #define CONFIG_SYS_MAXARGS 64 |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "firstboot=1\0"\ |
| "silent=1\0"\ |
| "upgrade_step=0\0"\ |
| "jtag=disable\0"\ |
| "loadaddr=0x00020000\0"\ |
| "os_ident_addr=0x00500000\0"\ |
| "loadaddr_rtos=0x00001000\0"\ |
| "loadaddr_kernel=0x03080000\0"\ |
| "otg_device=1\0" \ |
| "panel_type=lcd_1\0" \ |
| "outputmode=1080p60hz\0" \ |
| "hdmimode=1080p60hz\0" \ |
| "colorattribute=444,8bit\0"\ |
| "cvbsmode=576cvbs\0" \ |
| "vout_init=disable\0" \ |
| "display_width=1920\0" \ |
| "display_height=1080\0" \ |
| "display_bpp=16\0" \ |
| "display_color_index=16\0" \ |
| "display_layer=osd0\0" \ |
| "display_color_fg=0xffff\0" \ |
| "display_color_bg=0\0" \ |
| "dtb_mem_addr=0x01000000\0" \ |
| "fb_addr=0x00300000\0" \ |
| "fb_width=1920\0" \ |
| "fb_height=1080\0" \ |
| "hdmichecksum=0x00000000\0" \ |
| "dolby_status=0\0" \ |
| "dolby_vision_on=0\0" \ |
| "frac_rate_policy=1\0" \ |
| "hdr_policy=0\0" \ |
| "hdmi_read_edid=1\0" \ |
| "usb_burning=" CONFIG_USB_TOOL_ENTRY "\0" \ |
| "fdt_high=0x20000000\0"\ |
| "sdcburncfg=aml_sdc_burn.ini\0"\ |
| "EnableSelinux=enforcing\0" \ |
| "recovery_part=recovery\0"\ |
| "lock=10101000\0"\ |
| "recovery_offset=0\0"\ |
| "cvbs_drv=0\0"\ |
| "osd_reverse=0\0"\ |
| "video_reverse=0\0"\ |
| "active_slot=normal\0"\ |
| "boot_part=boot\0"\ |
| "vendor_boot_part=vendor_boot\0"\ |
| "board=ohm\0"\ |
| "Irq_check_en=0\0"\ |
| "common_dtb_load=" CONFIG_DTB_LOAD "\0"\ |
| "get_os_type=if store read ${os_ident_addr} ${boot_part} 0 0x1000; then os_ident ${os_ident_addr}; fi\0"\ |
| "fatload_dev=usb\0"\ |
| "fs_type=""rootfstype=ramfs""\0"\ |
| "initargs="\ |
| "init=/init" CONFIG_KNL_LOG_LEVEL "console=ttyS0,921600 no_console_suspend earlycon=aml-uart,0xfe07a000 "\ |
| "ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 loop.max_part=4 "\ |
| "\0"\ |
| "upgrade_check="\ |
| "echo recovery_status=${recovery_status};"\ |
| "if itest.s \"${recovery_status}\" == \"in_progress\"; then "\ |
| "run init_display;run storeargs; run recovery_from_flash;"\ |
| "else fi;"\ |
| "echo upgrade_step=${upgrade_step}; "\ |
| "if itest ${upgrade_step} == 3; then run init_display;run storeargs; run update; fi;"\ |
| "\0"\ |
| "storeargs="\ |
| "get_bootloaderversion;" \ |
| "setenv bootargs ${initargs} otg_device=${otg_device} "\ |
| "logo=${display_layer},loaded,${fb_addr} vout=${outputmode},${vout_init} panel_type=${panel_type} "\ |
| "hdmitx=${cecconfig},${colorattribute} hdmimode=${hdmimode} "\ |
| "hdmichecksum=${hdmichecksum} dolby_vision_on=${dolby_vision_on} " \ |
| "hdr_policy=${hdr_policy} hdr_priority=${hdr_priority} "\ |
| "frac_rate_policy=${frac_rate_policy} hdmi_read_edid=${hdmi_read_edid} cvbsmode=${cvbsmode} "\ |
| "osd_reverse=${osd_reverse} video_reverse=${video_reverse} irq_check_en=${Irq_check_en} "\ |
| "androidboot.selinux=${EnableSelinux} androidboot.firstboot=${firstboot} jtag=${jtag}; "\ |
| "setenv bootargs ${bootargs} androidboot.bootloader=${bootloader_version} androidboot.hardware=amlogic;"\ |
| "run cmdline_keys;"\ |
| "\0"\ |
| "switch_bootmode="\ |
| "get_rebootmode;"\ |
| "if test ${reboot_mode} = factory_reset; then "\ |
| "run recovery_from_flash;"\ |
| "else if test ${reboot_mode} = update; then "\ |
| "run update;"\ |
| "else if test ${reboot_mode} = quiescent; then "\ |
| "setenv bootargs ${bootargs} androidboot.quiescent=1;"\ |
| "else if test ${reboot_mode} = recovery_quiescent; then "\ |
| "setenv bootargs ${bootargs} androidboot.quiescent=1;"\ |
| "run recovery_from_flash;"\ |
| "else if test ${reboot_mode} = cold_boot; then "\ |
| "else if test ${reboot_mode} = fastboot; then "\ |
| "fastboot 0;"\ |
| "fi;fi;fi;fi;fi;fi;"\ |
| "\0" \ |
| "storeboot="\ |
| "run get_os_type;"\ |
| "run storage_param;"\ |
| "if test ${os_type} = rtos; then "\ |
| "setenv loadaddr ${loadaddr_rtos};"\ |
| "store read ${loadaddr} ${boot_part} 0 0x400000;"\ |
| "bootm ${loadaddr};"\ |
| "else if test ${os_type} = kernel; then "\ |
| "get_system_as_root_mode;"\ |
| "echo system_mode in storeboot: ${system_mode};"\ |
| "get_avb_mode;"\ |
| "echo active_slot in storeboot: ${active_slot};"\ |
| "if test ${system_mode} = 1; then "\ |
| "setenv bootargs ${bootargs} ro rootwait skip_initramfs;"\ |
| "else "\ |
| "setenv bootargs ${bootargs} androidboot.force_normal_boot=1;"\ |
| "fi;"\ |
| "if test ${active_slot} != normal; then "\ |
| "setenv bootargs ${bootargs} androidboot.slot_suffix=${active_slot};"\ |
| "fi;"\ |
| "if fdt addr ${dtb_mem_addr}; then else echo retry common dtb; run common_dtb_load; fi;"\ |
| "setenv loadaddr ${loadaddr_kernel};"\ |
| "if imgread kernel ${boot_part} ${loadaddr}; then bootm ${loadaddr}; fi;"\ |
| "else echo wrong OS format ${os_type}; fi;fi;"\ |
| "echo try upgrade as booting failure; run update;"\ |
| "\0" \ |
| "update="\ |
| /*first usb burning, second sdc_burn, third ext-sd autoscr/recovery, last udisk autoscr/recovery*/\ |
| "run usb_burning; "\ |
| "run recovery_from_sdcard;"\ |
| "run recovery_from_udisk;"\ |
| "run recovery_from_flash;"\ |
| "\0"\ |
| "recovery_from_fat_dev="\ |
| "setenv loadaddr ${loadaddr_kernel};"\ |
| "if fatload ${fatload_dev} 0 ${loadaddr} aml_autoscript; then autoscr ${loadaddr}; fi;"\ |
| "if fatload ${fatload_dev} 0 ${loadaddr} recovery.img; then "\ |
| "if fatload ${fatload_dev} 0 ${dtb_mem_addr} dtb.img; then echo ${fatload_dev} dtb.img loaded; fi;"\ |
| "setenv bootargs ${bootargs} ${fs_type};"\ |
| "bootm ${loadaddr};fi;"\ |
| "\0"\ |
| "recovery_from_udisk="\ |
| "setenv fatload_dev usb;"\ |
| "if usb start 0; then run recovery_from_fat_dev; fi;"\ |
| "\0"\ |
| "recovery_from_sdcard="\ |
| "setenv fatload_dev mmc;"\ |
| "if mmcinfo; then run recovery_from_fat_dev; fi;"\ |
| "\0"\ |
| "recovery_from_flash="\ |
| "echo active_slot: ${active_slot};"\ |
| "setenv loadaddr ${loadaddr_kernel};"\ |
| "if test ${active_slot} = normal; then "\ |
| "setenv bootargs ${bootargs} ${fs_type} aml_dt=${aml_dt} recovery_part=${recovery_part} recovery_offset=${recovery_offset};"\ |
| "if test ${upgrade_step} == 3; then "\ |
| "if ext4load mmc 1:2 ${dtb_mem_addr} /recovery/dtb.img; then echo cache dtb.img loaded; fi;"\ |
| "if ext4load mmc 1:2 ${loadaddr} /recovery/recovery.img; then echo cache recovery.img loaded; wipeisb; bootm ${loadaddr}; fi;"\ |
| "else "\ |
| "if imgread dtb recovery ${dtb_mem_addr}; then "\ |
| "else echo restore dtb; run common_dtb_load;"\ |
| "fi;"\ |
| "fi;"\ |
| "if imgread kernel ${recovery_part} ${loadaddr} ${recovery_offset}; then bootm ${loadaddr}; fi;"\ |
| "else "\ |
| "if fdt addr ${dtb_mem_addr}; then else echo retry common dtb; run common_dtb_load; fi;"\ |
| "if test ${partiton_mode} = normal; then "\ |
| "setenv bootargs ${bootargs} ${fs_type} aml_dt=${aml_dt} recovery_part=${boot_part} recovery_offset=${recovery_offset};"\ |
| "if imgread kernel ${boot_part} ${loadaddr}; then bootm ${loadaddr}; fi;"\ |
| "else "\ |
| "if test ${vendor_boot_mode} = true; then "\ |
| "setenv bootargs ${bootargs} ${fs_type} aml_dt=${aml_dt} recovery_part=${boot_part} recovery_offset=${recovery_offset} androidboot.slot_suffix=${active_slot};"\ |
| "if imgread kernel ${boot_part} ${loadaddr}; then bootm ${loadaddr}; fi;"\ |
| "else "\ |
| "setenv bootargs ${bootargs} ${fs_type} aml_dt=${aml_dt} recovery_part=${recovery_part} recovery_offset=${recovery_offset} androidboot.slot_suffix=${active_slot};"\ |
| "if imgread kernel ${recovery_part} ${loadaddr} ${recovery_offset}; then wipeisb; bootm ${loadaddr}; fi;"\ |
| "fi;"\ |
| "fi;"\ |
| "fi;"\ |
| "\0"\ |
| "bcb_cmd="\ |
| "get_avb_mode;"\ |
| "get_valid_slot;"\ |
| "if test ${vendor_boot_mode} = true; then "\ |
| "setenv loadaddr_kernel 0x3080000;"\ |
| "setenv dtb_mem_addr 0x1000000;"\ |
| "fi;"\ |
| "if test ${active_slot} != normal; then "\ |
| "echo ab mode, read dtb from kernel;"\ |
| "setenv common_dtb_load ""imgread dtb ${boot_part} ${dtb_mem_addr}"";"\ |
| "fi;"\ |
| "\0"\ |
| "init_display="\ |
| "get_rebootmode;"\ |
| "echo reboot_mode:::: ${reboot_mode};"\ |
| "if test ${reboot_mode} = quiescent; then "\ |
| "setenv reboot_mode_android ""quiescent"";"\ |
| "setenv dolby_status 0;"\ |
| "setenv dolby_vision_on 0;"\ |
| "run storeargs;"\ |
| "setenv bootargs ${bootargs} androidboot.quiescent=1;"\ |
| "osd open;osd clear;"\ |
| "else if test ${reboot_mode} = recovery_quiescent; then "\ |
| "setenv reboot_mode_android ""quiescent"";"\ |
| "setenv dolby_status 0;"\ |
| "setenv dolby_vision_on 0;"\ |
| "run storeargs;"\ |
| "setenv bootargs ${bootargs} androidboot.quiescent=1;"\ |
| "osd open;osd clear;"\ |
| "else "\ |
| "setenv reboot_mode_android ""normal"";"\ |
| "run storeargs;"\ |
| "hdmitx hpd;hdmitx get_preferred_mode;hdmitx get_parse_edid;setenv dolby_status 0;setenv dolby_vision_on 0;osd open;osd clear;imgread pic logo bootup $loadaddr;bmp display $bootup_offset;bmp scale;vout output ${outputmode};vpp hdrpkt;"\ |
| "fi;fi;"\ |
| "\0"\ |
| "storage_param="\ |
| "store param;"\ |
| "setenv bootargs ${bootargs} ${mtdbootparts}; "\ |
| "\0"\ |
| "cmdline_keys="\ |
| "setenv usid 1234567890; setenv region_code US;"\ |
| "if keyman init 0x1234; then "\ |
| "if keyman read usid ${loadaddr} str; then fi;"\ |
| "if keyman read region_code ${loadaddr} str; then fi;"\ |
| "if keyman read mac ${loadaddr} str; then "\ |
| "setenv bootargs ${bootargs} mac=${mac} androidboot.mac=${mac};"\ |
| "fi;"\ |
| "if keyman read deviceid ${loadaddr} str; then "\ |
| "setenv bootargs ${bootargs} androidboot.deviceid=${deviceid};"\ |
| "fi;"\ |
| "fi;"\ |
| "setenv bootargs ${bootargs} androidboot.wificountrycode=${region_code};"\ |
| "setenv bootargs ${bootargs} androidboot.serialno=${usid};"\ |
| "setenv serial ${usid}; setenv serial# ${usid};"\ |
| "factory_provision init;"\ |
| "\0"\ |
| "upgrade_key="\ |
| "if gpio input GPIOD_3; then "\ |
| "echo detect upgrade key; run update;"\ |
| "fi;"\ |
| "\0"\ |
| |
| #if 1 |
| #define CONFIG_PREBOOT \ |
| "run bcb_cmd; "\ |
| "run upgrade_check;"\ |
| "run init_display;"\ |
| "run storeargs;"\ |
| "run upgrade_key;" \ |
| "bcb uboot-command;"\ |
| "run switch_bootmode;" |
| #else |
| #define CONFIG_PREBOOT "echo preboot" |
| #endif |
| /* #define CONFIG_ENV_IS_NOWHERE 1 */ |
| #define CONFIG_ENV_SIZE (64*1024) |
| #define CONFIG_FIT 1 |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_ANDROID_BOOT_IMAGE 1 |
| #define CONFIG_SYS_BOOTM_LEN (64<<20) /* Increase max gunzip size*/ |
| |
| /* ATTENTION */ |
| /* DDR configs move to board/amlogic/[board]/firmware/timing.c */ |
| |
| /* running in sram */ |
| //#define UBOOT_RUN_IN_SRAM |
| #ifdef UBOOT_RUN_IN_SRAM |
| #define CONFIG_SYS_INIT_SP_ADDR (0x00200000) |
| /* Size of malloc() pool */ |
| #define CONFIG_SYS_MALLOC_LEN (256*1024) |
| #else |
| #define CONFIG_SYS_INIT_SP_ADDR (0x00200000) |
| #define CONFIG_SYS_MALLOC_LEN (96*1024*1024) |
| #endif |
| |
| //#define CONFIG_NR_DRAM_BANKS 1 |
| /* ddr functions */ |
| #define DDR_FULL_TEST 0 //0:disable, 1:enable. ddr full test |
| #define DDR_LOW_POWER 0 //0:disable, 1:enable. ddr clk gate for lp |
| #define DDR_ZQ_PD 0 //0:disable, 1:enable. ddr zq power down |
| #define DDR_USE_EXT_VREF 0 //0:disable, 1:enable. ddr use external vref |
| #define DDR4_TIMING_TEST 0 //0:disable, 1:enable. ddr4 timing test function |
| #define DDR_PLL_BYPASS 0 //0:disable, 1:enable. ddr pll bypass function |
| |
| /* storage: emmc/nand/sd */ |
| #define CONFIG_ENV_OVERWRITE |
| /* #define CONFIG_CMD_SAVEENV */ |
| /* fixme, need fix*/ |
| |
| #if (defined(CONFIG_ENV_IS_IN_AMLNAND) || defined(CONFIG_ENV_IS_IN_MMC)) && defined(CONFIG_STORE_COMPATIBLE) |
| #error env in amlnand/mmc already be compatible; |
| #endif |
| |
| /* |
| * storage |
| * |---------|---------| |
| * | | |
| * emmc<--Compatible-->nand |
| * |-------|-------| |
| * | | |
| * MTD<-Exclusive->NFTL |
| * | |
| * |***************|***************| |
| * slc-nand SPI-nand SPI-nor |
| * (raw nand) |
| */ |
| /* axg only support slc nand */ |
| /* swither for mtd nand which is for slc only. */ |
| |
| |
| #if defined(CONFIG_AML_NAND) && defined(CONFIG_MESON_NFC) |
| #error CONFIG_AML_NAND/CONFIG_MESON_NFC can not support at the sametime; |
| #endif |
| |
| #if (defined(CONFIG_AML_NAND) || defined(CONFIG_MESON_NFC)) && defined(CONFIG_MESON_FBOOT) |
| #error CONFIG_AML_NAND/CONFIG_MESON_NFC CONFIG _MESON_FBOOT can not support at the sametime; |
| #endif |
| |
| #if defined(CONFIG_SPI_NAND) && defined(CONFIG_MTD_SPI_NAND) && defined(CONFIG_MESON_NFC) |
| #error CONFIG_SPI_NAND/CONFIG_MTD_SPI_NAND/CONFIG_MESON_NFC can not support at the sametime; |
| #endif |
| |
| /* #define CONFIG_AML_SD_EMMC 1 */ |
| #ifdef CONFIG_AML_SD_EMMC |
| #define CONFIG_GENERIC_MMC 1 |
| #define CONFIG_CMD_MMC 1 |
| #define CONFIG_CMD_GPT 1 |
| #define CONFIG_SYS_MMC_ENV_DEV 1 |
| #define CONFIG_EMMC_DDR52_EN 0 |
| #define CONFIG_EMMC_DDR52_CLK 35000000 |
| #endif |
| #define CONFIG_PARTITIONS 1 |
| #if 0 |
| #define CONFIG_SYS_NO_FLASH 1 |
| #endif |
| |
| #if defined CONFIG_MESON_NFC || defined CONFIG_SPI_NAND || defined CONFIG_MTD_SPI_NAND |
| #define CONFIG_SYS_MAX_NAND_DEVICE 2 |
| #endif |
| |
| /* vpu */ |
| #define AML_VPU_CLK_LEVEL_DFT 7 |
| |
| /* osd */ |
| #define OSD_SCALE_ENABLE |
| #define AML_OSD_HIGH_VERSION |
| |
| /* USB |
| * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard |
| * Enable CONFIG_MUSB_UDD for Device functionalities. |
| */ |
| /* #define CONFIG_MUSB_UDC 1 */ |
| /* #define CONFIG_CMD_USB 1 */ |
| |
| #define USB_PHY2_PLL_PARAMETER_1 0x09400414 |
| #define USB_PHY2_PLL_PARAMETER_2 0x927e0000 |
| #define USB_PHY2_PLL_PARAMETER_3 0xAC5F49E5 |
| |
| #define USB_G12x_PHY_PLL_SETTING_1 (0xfe18) |
| #define USB_G12x_PHY_PLL_SETTING_2 (0xfff) |
| #define USB_G12x_PHY_PLL_SETTING_3 (0x78000) |
| #define USB_G12x_PHY_PLL_SETTING_4 (0xe0004) |
| #define USB_G12x_PHY_PLL_SETTING_5 (0xe000c) |
| |
| #define AML_TXLX_USB 1 |
| #define AML_USB_V2 1 |
| #define USB_GENERAL_BIT 3 |
| #define USB_PHY21_BIT 4 |
| |
| /* UBOOT fastboot config */ |
| |
| |
| /* UBOOT Facotry usb/sdcard burning config */ |
| |
| /* net */ |
| #define CONFIG_CMD_NET 1 |
| #define CONFIG_ETH_DESIGNWARE |
| #if defined(CONFIG_CMD_NET) |
| #define CONFIG_DESIGNWARE_ETH 1 |
| #define CONFIG_PHYLIB 1 |
| #define CONFIG_NET_MULTI 1 |
| #define CONFIG_CMD_PING 1 |
| #define CONFIG_CMD_DHCP 1 |
| #define CONFIG_CMD_RARP 1 |
| #define CONFIG_HOSTNAME "arm_gxbb" |
| #if 0 |
| #define CONFIG_RANDOM_ETHADDR 1 /* use random eth addr, or default */ |
| #endif |
| #define CONFIG_ETHADDR 00:15:18:01:81:31 /* Ethernet address */ |
| #define CONFIG_IPADDR 10.18.9.97 /* Our ip address */ |
| #define CONFIG_GATEWAYIP 10.18.9.1 /* Our getway ip address */ |
| #define CONFIG_SERVERIP 10.18.9.113 /* Tftp server ip address */ |
| #define CONFIG_NETMASK 255.255.255.0 |
| #endif /* (CONFIG_CMD_NET) */ |
| |
| #define MAC_ADDR_NEW 1 |
| |
| /* other devices */ |
| #define CONFIG_SHA1 1 |
| #define CONFIG_MD5 1 |
| |
| /* commands */ |
| |
| /*file system*/ |
| #define CONFIG_DOS_PARTITION 1 |
| #define CONFIG_EFI_PARTITION 1 |
| /* #define CONFIG_MMC 1 */ |
| #define CONFIG_FS_FAT 1 |
| #define CONFIG_FS_EXT4 1 |
| #define CONFIG_LZO 1 |
| |
| /* Cache Definitions */ |
| /* #define CONFIG_SYS_DCACHE_OFF */ |
| /* #define CONFIG_SYS_ICACHE_OFF */ |
| |
| /* other functions */ |
| #define CONFIG_LIBAVB 1 |
| |
| /* define CONFIG_SYS_MEM_TOP_HIDE 8M space for free buffer */ |
| #define CONFIG_SYS_MEM_TOP_HIDE 0x00800000 |
| |
| /* define CONFIG_UPDATE_MMU_TABLE for need update mmu */ |
| //#define CONFIG_UPDATE_MMU_TABLE |
| |
| #define CONFIG_CPU_ARMV8 |
| |
| //use sha2 command |
| #define CONFIG_CMD_SHA2 |
| #define CONFIG_CMD_STARTDSP |
| |
| //use hardware sha2 |
| //#define CONFIG_AML_HW_SHA2 |
| |
| #define CONFIG_MULTI_DTB 1 |
| #define CONFIG_AUTO_ADAPT_DDR_DTB 1 |
| |
| /* support secure boot */ |
| #define CONFIG_AML_SECURE_UBOOT 1 |
| |
| #if defined(CONFIG_AML_SECURE_UBOOT) |
| |
| /* unify build for generate encrypted bootloader "u-boot.bin.encrypt" */ |
| #define CONFIG_AML_CRYPTO_UBOOT 1 |
| //#define CONFIG_AML_SIGNED_UBOOT 1 |
| /* unify build for generate encrypted kernel image |
| SRC : "board/amlogic/(board)/boot.img" |
| DST : "fip/boot.img.encrypt" */ |
| /* #define CONFIG_AML_CRYPTO_IMG 1 */ |
| |
| #endif /* CONFIG_AML_SECURE_UBOOT */ |
| |
| #define CONFIG_FIP_IMG_SUPPORT 1 |
| |
| #define BL32_SHARE_MEM_SIZE 0x800000 |
| |
| #endif |
| |
