| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (c) 2019 Amlogic, Inc. All rights reserved. |
| */ |
| |
| #include <asm/arch/secure_apb.h> |
| #include <asm/arch/timing.h> |
| #include <asm/arch/ddr_define.h> |
| |
| /* board clk defines */ |
| #define CPU_CLK 1512 |
| |
| /* ddr config support multiple configs for boards which use same bootloader: |
| * config steps: |
| * 1. add a new data struct in __ddr_setting[] |
| * 2. config correct board_id, ddr_type, freq, etc.. |
| */ |
| |
| |
| /* CAUTION!! */ |
| /* Confirm ddr configs with hardware designer, |
| * if you don't know how to config, then don't edit it |
| */ |
| |
| /* Key configs */ |
| /* |
| * board_id: check hardware adc config |
| * dram_rank_config: |
| * #define CONFIG_DDR_CHL_AUTO 0xF |
| * #define CONFIG_DDR0_16BIT_CH0 0x1 |
| * #define CONFIG_DDR0_16BIT_RANK01_CH0 0x4 |
| * #define CONFIG_DDR0_32BIT_RANK0_CH0 0x2 |
| * #define CONFIG_DDR0_32BIT_RANK01_CH01 0x3 |
| * #define CONFIG_DDR0_32BIT_16BIT_RANK0_CH0 0x5 |
| * #define CONFIG_DDR0_32BIT_16BIT_RANK01_CH0 0x6 |
| * DramType: |
| * #define CONFIG_DDR_TYPE_DDR3 0 |
| * #define CONFIG_DDR_TYPE_DDR4 1 |
| * #define CONFIG_DDR_TYPE_LPDDR4 2 |
| * #define CONFIG_DDR_TYPE_LPDDR3 3 |
| * DRAMFreq: |
| * {pstate0, pstate1, pstate2, pstate3} //more than one pstate means use dynamic freq |
| * |
| */ |
| |
| |
| /* ddr configs */ |
| #define DDR_RFC_TYPE_DDR3_512Mbx1 0 |
| #define DDR_RFC_TYPE_DDR3_512Mbx2 1 |
| #define DDR_RFC_TYPE_DDR3_512Mbx4 2 |
| #define DDR_RFC_TYPE_DDR3_512Mbx8 3 |
| #define DDR_RFC_TYPE_DDR3_512Mbx16 4 |
| #define DDR_RFC_TYPE_DDR4_2Gbx1 5 |
| #define DDR_RFC_TYPE_DDR4_2Gbx2 6 |
| #define DDR_RFC_TYPE_DDR4_2Gbx4 7 |
| #define DDR_RFC_TYPE_DDR4_2Gbx8 8 |
| |
| #define DDR_RFC_TYPE_LPDDR4_2Gbx1 9 |
| #define DDR_RFC_TYPE_LPDDR4_3Gbx1 10 |
| #define DDR_RFC_TYPE_LPDDR4_4Gbx1 11 |
| |
| ddr_set_t __ddr_setting[] __attribute__ ((section(".ddr_param"))) = { |
| { |
| /* ddr3 */ |
| .board_id = CONFIG_BOARD_ID_MASK, |
| .version = 1, |
| .dram_rank_config = CONFIG_DDR0_32BIT_16BIT_RANK0_CH0,//CONFIG_DDR0_16BIT_CH0, |
| .DramType = CONFIG_DDR_TYPE_DDR3, |
| /* DRAMFreq = 192, 256, 384, 512, 768-1536 */ |
| .DRAMFreq = {912, 0, 0, 0}, |
| .ddr_base_addr = CFG_DDR_BASE_ADDR, |
| .ddr_start_offset = CFG_DDR_START_OFFSET, |
| //.dmem_load_size = 0x1000, //4K |
| |
| .DisabledDbyte = 0xf0, |
| .Is2Ttiming = 1, |
| .HdtCtrl = 0xC8, |
| .dram_cs0_size_MB = 768, |
| .dram_cs1_size_MB = 0, |
| .training_SequenceCtrl = {0x31f,0}, //ddr3 0x21f 0x31f |
| .phy_odt_config_rank = {0x23,0x13}, //use 0x23 0x13 compatibility with 1rank and 2rank //targeting rank 0. [3:0] is used //for write ODT [7:4] is used for //read ODT |
| .dfi_odt_config = 0x0d0d, //use 0d0d compatibility with 1rank and 2rank //0808 |
| .PllBypassEn = 0, //bit0-ps0,bit1-ps1 |
| .ddr_rdbi_wr_enable = 0, |
| .clk_drv_ohm = 40, |
| .cs_drv_ohm = 40, |
| .ac_drv_ohm = 40, |
| .soc_data_drv_ohm_p = 34, |
| .soc_data_drv_ohm_n = 34, |
| .soc_data_odt_ohm_p = 60, //48, |
| .soc_data_odt_ohm_n = 0, |
| .dram_data_drv_ohm = 34, //ddr4 sdram only 34 or 48, skt board use 34 better |
| .dram_data_odt_ohm = 60, |
| .dram_ac_odt_ohm = 0, |
| .soc_clk_slew_rate = 0x300, |
| .soc_cs_slew_rate = 0x300, |
| .soc_ac_slew_rate = 0x300, |
| .soc_data_slew_rate = 0x200, |
| .vref_output_permil = 500, |
| .vref_receiver_permil = 500, //700, |
| .vref_dram_permil = 500, //700, |
| //.vref_reverse = 0, |
| .ac_trace_delay = {32,32,32,32,32,32,32,32,32,32}, |
| //{00,00}, |
| .ac_pinmux = {00,00}, |
| #if 1 |
| .ddr_dmc_remap = { |
| [0] = ( 5 | 7 << 5 | 8 << 10 | 9 << 15 | 10 << 20 | 11 << 25 ), |
| [1] = ( 12| 0 << 5 | 0 << 10 | 14 << 15 | 15 << 20 | 16 << 25 ), |
| [2] = ( 17| 18 << 5 | 19 << 10 | 21 << 15 | 22 << 20 | 23 << 25 ), |
| [3] = ( 24| 25 << 5 | 26 << 10 | 27 << 15 | 28 << 20 | 29 << 25 ), |
| [4] = ( 30| 13 << 5 | 20 << 10 | 6 << 15 | 0 << 20 | 0 << 25 ), |
| }, |
| #else |
| //16bit |
| .ddr_dmc_remap = { |
| [0] = ( 0 | 5 << 5 | 6<< 10 | 7 << 15 | 8 << 20 | 9 << 25 ), |
| [1] = ( 10| 0 << 5 | 0 << 10 | 14 << 15 | 15 << 20 | 16 << 25 ), |
| [2] = ( 17|( 18 << 5) |( 19 << 10) |( 20 << 15) |( 21 << 20) | (22 << 25 )), |
| [3] = ( 23| 24 << 5 | 25 << 10 | 26 << 15 | 27 << 20 | 28 << 25 ), |
| [4] = ( 29| 11<< 5 | 12 << 10 | 13<< 15 | 0 << 20 | 0 << 25 ), |
| }, |
| #endif |
| .ddr_lpddr34_ca_remap = {00,00}, |
| .ddr_lpddr34_dq_remap = {00,00}, |
| .dram_rtt_nom_wr_park = {00,00}, |
| |
| /* pll ssc config: |
| * |
| * pll_ssc_mode = (1<<20) | (1<<8) | ([strength] << 4) | [mode], |
| * ppm = strength * 500 |
| * mode: 0=center, 1=up, 2=down |
| * |
| * eg: |
| * 1. config 1000ppm center ss. then mode=0, strength=2 |
| * .pll_ssc_mode = (1<<20) | (1<<8) | (2 << 4) | 0, |
| * 2. config 3000ppm down ss. then mode=2, strength=6 |
| * .pll_ssc_mode = (1<<20) | (1<<8) | (6 << 4) | 2, |
| */ |
| .pll_ssc_mode = (1<<20) | (1<<8) | (2<<4) | 0,//center_ssc_1000ppm |
| .ddr_func = DDR_FUNC, |
| .magic = DRAM_CFG_MAGIC, |
| }, |
| { |
| /* ddr4 */ |
| .board_id = CONFIG_BOARD_ID_MASK, |
| .version = 1, |
| .dram_rank_config = CONFIG_DDR0_32BIT_RANK0_CH0, |
| .ddr_rfc_type = DDR_RFC_TYPE_DDR4_2Gbx8, |
| .DramType = CONFIG_DDR_TYPE_DDR4, |
| .DRAMFreq = {1176, 0, 0, 0}, |
| .ddr_base_addr = CFG_DDR_BASE_ADDR, |
| .ddr_start_offset = CFG_DDR_START_OFFSET, |
| //.dmem_load_size = 0x1000, //4K |
| |
| .DisabledDbyte = 0xf0, |
| .Is2Ttiming = 1, |
| .HdtCtrl = 0xC8, |
| .dram_cs0_size_MB = 0xffff, |
| .dram_cs1_size_MB = 0, |
| .training_SequenceCtrl = {0x31f,0x61}, //ddr3 0x21f 0x31f |
| .phy_odt_config_rank = {0x23,0x13}, //use 0x23 0x13 compatibility with 1rank and 2rank //targeting rank 0. [3:0] is used //for write ODT [7:4] is used for //read ODT |
| .dfi_odt_config = 0x0d0d, //use 0d0d compatibility with 1rank and 2rank //0808 |
| .PllBypassEn = 0, //bit0-ps0,bit1-ps1 |
| .ddr_rdbi_wr_enable = 0, |
| .clk_drv_ohm = 40, |
| .cs_drv_ohm = 40, |
| .ac_drv_ohm = 40, |
| .soc_data_drv_ohm_p = 40, |
| .soc_data_drv_ohm_n = 40, |
| .soc_data_odt_ohm_p = 60, |
| .soc_data_odt_ohm_n = 0, |
| .dram_data_drv_ohm = 34,//48, //34, //ddr4 sdram only 34 or 48, skt board use 34 better |
| .dram_data_odt_ohm = 60, //60, |
| .dram_ac_odt_ohm = 0, |
| .soc_clk_slew_rate = 0x3ff, |
| .soc_cs_slew_rate = 0x3ff, |
| .soc_ac_slew_rate = 0x3ff, |
| .soc_data_slew_rate = 0x2ff, |
| .vref_output_permil = 500, |
| .vref_receiver_permil = 0,//700, |
| .vref_dram_permil = 0,//700, |
| //.vref_reverse = 0, |
| //.ac_trace_delay = {0x0,0x0},// {0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40}, |
| .ac_trace_delay = {16,32,32,32,32,32,32,32,32,32}, |
| .ddr_dmc_remap = { |
| [0] = ( 5 | 7 << 5 | 8 << 10 | 9 << 15 | 10 << 20 | 11 << 25 ), |
| [1] = ( 12| 0 << 5 | 0 << 10 | 14 << 15 | 15 << 20 | 16 << 25 ), |
| [2] = ( 17| 18 << 5 | 19 << 10 | 21 << 15 | 22 << 20 | 23 << 25 ), |
| [3] = ( 24| 25 << 5 | 26 << 10 | 27 << 15 | 28 << 20 | 29 << 25 ), |
| [4] = ( 30| 13 << 5 | 20 << 10 | 6 << 15 | 0 << 20 | 0 << 25 ), |
| }, |
| .ddr_lpddr34_ca_remap = {00,00}, |
| .ddr_lpddr34_dq_remap = {00,00}, |
| .dram_rtt_nom_wr_park = {00,00}, |
| |
| /* pll ssc config: |
| * |
| * pll_ssc_mode = (1<<20) | (1<<8) | ([strength] << 4) | [mode], |
| * ppm = strength * 500 |
| * mode: 0=center, 1=up, 2=down |
| * |
| * eg: |
| * 1. config 1000ppm center ss. then mode=0, strength=2 |
| * .pll_ssc_mode = (1<<20) | (1<<8) | (2 << 4) | 0, |
| * 2. config 3000ppm down ss. then mode=2, strength=6 |
| * .pll_ssc_mode = (1<<20) | (1<<8) | (6 << 4) | 2, |
| */ |
| .pll_ssc_mode = (1<<20) | (1<<8) | (2<<4) | 0,//center_ssc_1000ppm |
| .ddr_func = DDR_FUNC, |
| .magic = DRAM_CFG_MAGIC, |
| }, |
| }; |
| |
| board_clk_set_t __board_clk_setting |
| __attribute__ ((section(".clk_param"))) = { |
| /* clock settings for bl2 */ |
| .cpu_clk = CPU_CLK / 24 * 24, |
| #ifdef CONFIG_PXP_EMULATOR |
| .pxp = 1, |
| #else |
| .pxp = 0, |
| #endif |
| }; |
| |
| |
| #define VCCK_VAL AML_VCCK_INIT_VOLTAGE |
| #define VDDEE_VAL AML_VDDEE_INIT_VOLTAGE |
| /* VCCK PWM table */ |
| #if (VCCK_VAL == 1039) |
| #define VCCK_VAL_REG 0x00000022 |
| #elif (VCCK_VAL == 1029) |
| #define VCCK_VAL_REG 0x00010021 |
| #elif (VCCK_VAL == 1019) |
| #define VCCK_VAL_REG 0x00020020 |
| #elif (VCCK_VAL == 1009) |
| #define VCCK_VAL_REG 0x0003001f |
| #elif (VCCK_VAL == 999) |
| #define VCCK_VAL_REG 0x0004001e |
| #elif (VCCK_VAL == 989) |
| #define VCCK_VAL_REG 0x0005001d |
| #elif (VCCK_VAL == 979) |
| #define VCCK_VAL_REG 0x0006001c |
| #elif (VCCK_VAL == 969) |
| #define VCCK_VAL_REG 0x0007001b |
| #elif (VCCK_VAL == 959) |
| #define VCCK_VAL_REG 0x0008001a |
| #elif (VCCK_VAL == 949) |
| #define VCCK_VAL_REG 0x00090019 |
| #elif (VCCK_VAL == 939) |
| #define VCCK_VAL_REG 0x000a0018 |
| #elif (VCCK_VAL == 929) |
| #define VCCK_VAL_REG 0x000b0017 |
| #elif (VCCK_VAL == 919) |
| #define VCCK_VAL_REG 0x000c0016 |
| #elif (VCCK_VAL == 909) |
| #define VCCK_VAL_REG 0x000d0015 |
| #elif (VCCK_VAL == 899) |
| #define VCCK_VAL_REG 0x000e0014 |
| #elif (VCCK_VAL == 889) |
| #define VCCK_VAL_REG 0x000f0013 |
| #elif (VCCK_VAL == 879) |
| #define VCCK_VAL_REG 0x00100012 |
| #elif (VCCK_VAL == 869) |
| #define VCCK_VAL_REG 0x00110011 |
| #elif (VCCK_VAL == 859) |
| #define VCCK_VAL_REG 0x00120010 |
| #elif (VCCK_VAL == 849) |
| #define VCCK_VAL_REG 0x0013000f |
| #elif (VCCK_VAL == 839) |
| #define VCCK_VAL_REG 0x0014000e |
| #elif (VCCK_VAL == 829) |
| #define VCCK_VAL_REG 0x0015000d |
| #elif (VCCK_VAL == 819) |
| #define VCCK_VAL_REG 0x0016000c |
| #elif (VCCK_VAL == 809) |
| #define VCCK_VAL_REG 0x0017000b |
| #elif (VCCK_VAL == 799) |
| #define VCCK_VAL_REG 0x0018000a |
| #elif (VCCK_VAL == 789) |
| #define VCCK_VAL_REG 0x00190009 |
| #elif (VCCK_VAL == 779) |
| #define VCCK_VAL_REG 0x001a0008 |
| #elif (VCCK_VAL == 769) |
| #define VCCK_VAL_REG 0x001b0007 |
| #elif (VCCK_VAL == 759) |
| #define VCCK_VAL_REG 0x001c0006 |
| #elif (VCCK_VAL == 749) |
| #define VCCK_VAL_REG 0x001d0005 |
| #elif (VCCK_VAL == 739) |
| #define VCCK_VAL_REG 0x001e0004 |
| #elif (VCCK_VAL == 729) |
| #define VCCK_VAL_REG 0x001f0003 |
| #elif (VCCK_VAL == 719) |
| #define VCCK_VAL_REG 0x00200002 |
| #elif (VCCK_VAL == 709) |
| #define VCCK_VAL_REG 0x00210001 |
| #elif (VCCK_VAL == 699) |
| #define VCCK_VAL_REG 0x00220000 |
| #else |
| #error "VCCK val out of range\n" |
| #endif |
| |
| /* VDDEE_VAL_REG */ |
| #if (VDDEE_VAL == 700) |
| #define VDDEE_VAL_REG 0x120000 |
| #elif (VDDEE_VAL == 710) |
| #define VDDEE_VAL_REG 0x110001 |
| #elif (VDDEE_VAL == 720) |
| #define VDDEE_VAL_REG 0x100002 |
| #elif (VDDEE_VAL == 730) |
| #define VDDEE_VAL_REG 0xf0003 |
| #elif (VDDEE_VAL == 740) |
| #define VDDEE_VAL_REG 0xe0004 |
| #elif (VDDEE_VAL == 750) |
| #define VDDEE_VAL_REG 0xd0005 |
| #elif (VDDEE_VAL == 760) |
| #define VDDEE_VAL_REG 0xc0006 |
| #elif (VDDEE_VAL == 770) |
| #define VDDEE_VAL_REG 0xb0007 |
| #elif (VDDEE_VAL == 780) |
| #define VDDEE_VAL_REG 0xa0008 |
| #elif (VDDEE_VAL == 790) |
| #define VDDEE_VAL_REG 0x90009 |
| #elif (VDDEE_VAL == 800) |
| #define VDDEE_VAL_REG 0x8000a |
| #elif (VDDEE_VAL == 810) |
| #define VDDEE_VAL_REG 0x7000b |
| #elif (VDDEE_VAL == 820) |
| #define VDDEE_VAL_REG 0x6000c |
| #elif (VDDEE_VAL == 830) |
| #define VDDEE_VAL_REG 0x5000d |
| #elif (VDDEE_VAL == 840) |
| #define VDDEE_VAL_REG 0x4000e |
| #elif (VDDEE_VAL == 850) |
| #define VDDEE_VAL_REG 0x3000f |
| #elif (VDDEE_VAL == 860) |
| #define VDDEE_VAL_REG 0x20010 |
| #elif (VDDEE_VAL == 870) |
| #define VDDEE_VAL_REG 0x10011 |
| #elif (VDDEE_VAL == 880) |
| #define VDDEE_VAL_REG 0x12 |
| #else |
| #error "VDDEE val out of range\n" |
| #endif |
| |
| bl2_reg_t __bl2_reg[] __attribute__ ((section(".generic_param"))) = { |
| //hxbao, need fine tune |
| {0, 0, 0xffffffff, 0, 0, 0}, |
| }; |
| |
| /* gpio/pinmux/pwm init */ |
| register_ops_t __bl2_ops_reg[MAX_REG_OPS_ENTRIES] |
| __attribute__ ((section(".misc_param"))) = { |
| /* demo, user defined override register */ |
| {PWMGH_PWM_B, VDDEE_VAL_REG, 0xffffffff, 0, 0, 0}, |
| {PWMIJ_PWM_B, VCCK_VAL_REG, 0xffffffff, 0, 0, 0}, |
| {PWMGH_MISC_REG_AB, (0x1 << 1), (0x1 << 1), 0, 0, 0}, |
| {PWMIJ_MISC_REG_AB, (0x1 << 1), (0x1 << 1), 0, 0, 0}, |
| /* enable vddcpu dc-dc, set TEST_N to high */ |
| {PADCTRL_TESTN_O, (0x1 << 0), (0x1 << 0), 0, 0, 0}, |
| {PADCTRL_TESTN_OEN, (0x0 << 0), (0x1 << 0), 0, 0, 0}, |
| /* set pwm h and pwm j clock rate to 24M, enable them */ |
| {CLKCTRL_PWM_CLK_GH_CTRL, (1 << 8 | 1 << 24) , 0xffffffff, 0, 0, 0}, |
| {CLKCTRL_PWM_CLK_IJ_CTRL, (1 << 8 | 1 << 24) , 0xffffffff, 0, 0, 0}, |
| /* set GPIOE_0 GPIOE_1 drive strength to 3 */ |
| {PADCTRL_GPIOE_DS, 0xf, 0xf, 0, 0, 0}, |
| /* set GPIOE_0 GPIOE_1 mux to pwmh pwmj */ |
| {PADCTRL_PIN_MUX_REGI, (0x3 << 0), (0xf << 0), 0, 0, 0}, |
| {PADCTRL_PIN_MUX_REGI, (0x3 << 4), (0xf << 4), 0, 0, 0}, |
| }; |
| |
| #define DEV_FIP_SIZE 0x300000 |
| #define DDR_FIP_SIZE 0x40000 |
| /* for all the storage parameter */ |
| storage_parameter_t __store_para __attribute__ ((section(".store_param"))) = { |
| .common = { |
| .version = 0x01, |
| .device_fip_container_size = DEV_FIP_SIZE, |
| .device_fip_container_copies = 4, |
| .ddr_fip_container_size = DDR_FIP_SIZE, |
| }, |
| .nand = { |
| .version = 0x01, |
| .bbt_pages = 0x01, |
| .bbt_start_block = 20, |
| .discrete_mode = 1, |
| .setup_data.nand_setup_data = (2 << 20) | \ |
| (0 << 19) | \ |
| (1 << 17) | \ |
| (1 << 14) | \ |
| (0 << 13) | \ |
| (64 << 6) | \ |
| (4 << 0), |
| .reserved_area_blk_cnt = 48, |
| .page_per_block = 64, |
| .use_param_page_list = 0, |
| }, |
| }; |
