blob: 76aa69a35b365e061a142ab382ddb88ad31d30e3 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2017 NXP
*/
/dts-v1/;
#include "imx7d.dtsi"
/ {
model = "Freescale i.MX7 SabreSD Board";
compatible = "fsl,imx7d-sdb", "fsl,imx7d";
aliases {
spi5 = &soft_spi;
};
memory {
reg = <0x80000000 0x80000000>;
};
soft_spi: soft-spi {
compatible = "spi-gpio";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi1>;
status = "okay";
gpio-sck = <&gpio1 13 0>;
gpio-mosi = <&gpio1 9 0>;
cs-gpios = <&gpio1 12 0>;
num-chipselects = <1>;
#address-cells = <1>;
#size-cells = <0>;
gpio_spi: gpio_spi@0 {
compatible = "fairchild,74hc595";
gpio-controller;
#gpio-cells = <2>;
reg = <0>;
registers-number = <1>;
registers-default = /bits/ 8 <0x74>; /* Enable PERI_3V3, SENSOR_RST_B and HDMI_RST*/
spi-max-frequency = <100000>;
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
reg_usb_otg1_vbus: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "usb_otg1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_usb_otg2_vbus: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
regulator-name = "usb_otg2_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_sd1_vmmc: regulator@3 {
compatible = "regulator-fixed";
regulator-name = "VDD_SD1";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
startup-delay-us = <200000>;
enable-active-high;
};
};
};
&iomuxc {
imx7d-sdb {
pinctrl_spi1: spi1grp {
fsl,pins = <
MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x59
MX7D_PAD_GPIO1_IO12__GPIO1_IO12 0x59
MX7D_PAD_GPIO1_IO13__GPIO1_IO13 0x59
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX7D_PAD_I2C1_SDA__I2C1_SDA 0x4000007f
MX7D_PAD_I2C1_SCL__I2C1_SCL 0x4000007f
>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX7D_PAD_I2C2_SDA__I2C2_SDA 0x4000007f
MX7D_PAD_I2C2_SCL__I2C2_SCL 0x4000007f
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX7D_PAD_I2C3_SDA__I2C3_SDA 0x4000007f
MX7D_PAD_I2C3_SCL__I2C3_SCL 0x4000007f
>;
};
pinctrl_i2c4: i2c4grp {
fsl,pins = <
MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA 0x4000007f
MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL 0x4000007f
>;
};
pinctrl_usdhc1_gpio: usdhc1_gpiogrp {
fsl,pins = <
MX7D_PAD_SD1_CD_B__GPIO5_IO0 0x59 /* CD */
MX7D_PAD_SD1_WP__GPIO5_IO1 0x59 /* WP */
MX7D_PAD_SD1_RESET_B__GPIO5_IO2 0x59 /* vmmc */
MX7D_PAD_GPIO1_IO08__SD1_VSELECT 0x59 /* VSELECT */
>;
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX7D_PAD_SD1_CMD__SD1_CMD 0x59
MX7D_PAD_SD1_CLK__SD1_CLK 0x19
MX7D_PAD_SD1_DATA0__SD1_DATA0 0x59
MX7D_PAD_SD1_DATA1__SD1_DATA1 0x59
MX7D_PAD_SD1_DATA2__SD1_DATA2 0x59
MX7D_PAD_SD1_DATA3__SD1_DATA3 0x59
>;
};
pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
fsl,pins = <
MX7D_PAD_SD1_CMD__SD1_CMD 0x5a
MX7D_PAD_SD1_CLK__SD1_CLK 0x1a
MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5a
MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5a
MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5a
MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5a
>;
};
pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
fsl,pins = <
MX7D_PAD_SD1_CMD__SD1_CMD 0x5b
MX7D_PAD_SD1_CLK__SD1_CLK 0x1b
MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5b
MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5b
MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5b
MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5b
>;
};
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX7D_PAD_SD2_CMD__SD2_CMD 0x59
MX7D_PAD_SD2_CLK__SD2_CLK 0x19
MX7D_PAD_SD2_DATA0__SD2_DATA0 0x59
MX7D_PAD_SD2_DATA1__SD2_DATA1 0x59
MX7D_PAD_SD2_DATA2__SD2_DATA2 0x59
MX7D_PAD_SD2_DATA3__SD2_DATA3 0x59
MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21 0x19 /* WL_REG_ON */
MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20 0x19 /* WL_HOST_WAKE */
>;
};
pinctrl_usdhc2_100mhz: usdhc2grp_100mhz {
fsl,pins = <
MX7D_PAD_SD2_CMD__SD2_CMD 0x5a
MX7D_PAD_SD2_CLK__SD2_CLK 0x1a
MX7D_PAD_SD2_DATA0__SD2_DATA0 0x5a
MX7D_PAD_SD2_DATA1__SD2_DATA1 0x5a
MX7D_PAD_SD2_DATA2__SD2_DATA2 0x5a
MX7D_PAD_SD2_DATA3__SD2_DATA3 0x5a
>;
};
pinctrl_usdhc2_200mhz: usdhc2grp_200mhz {
fsl,pins = <
MX7D_PAD_SD2_CMD__SD2_CMD 0x5b
MX7D_PAD_SD2_CLK__SD2_CLK 0x1b
MX7D_PAD_SD2_DATA0__SD2_DATA0 0x5b
MX7D_PAD_SD2_DATA1__SD2_DATA1 0x5b
MX7D_PAD_SD2_DATA2__SD2_DATA2 0x5b
MX7D_PAD_SD2_DATA3__SD2_DATA3 0x5b
>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX7D_PAD_SD3_CMD__SD3_CMD 0x59
MX7D_PAD_SD3_CLK__SD3_CLK 0x19
MX7D_PAD_SD3_DATA0__SD3_DATA0 0x59
MX7D_PAD_SD3_DATA1__SD3_DATA1 0x59
MX7D_PAD_SD3_DATA2__SD3_DATA2 0x59
MX7D_PAD_SD3_DATA3__SD3_DATA3 0x59
MX7D_PAD_SD3_DATA4__SD3_DATA4 0x59
MX7D_PAD_SD3_DATA5__SD3_DATA5 0x59
MX7D_PAD_SD3_DATA6__SD3_DATA6 0x59
MX7D_PAD_SD3_DATA7__SD3_DATA7 0x59
MX7D_PAD_SD3_STROBE__SD3_STROBE 0x19
>;
};
pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
fsl,pins = <
MX7D_PAD_SD3_CMD__SD3_CMD 0x5a
MX7D_PAD_SD3_CLK__SD3_CLK 0x1a
MX7D_PAD_SD3_DATA0__SD3_DATA0 0x5a
MX7D_PAD_SD3_DATA1__SD3_DATA1 0x5a
MX7D_PAD_SD3_DATA2__SD3_DATA2 0x5a
MX7D_PAD_SD3_DATA3__SD3_DATA3 0x5a
MX7D_PAD_SD3_DATA4__SD3_DATA4 0x5a
MX7D_PAD_SD3_DATA5__SD3_DATA5 0x5a
MX7D_PAD_SD3_DATA6__SD3_DATA6 0x5a
MX7D_PAD_SD3_DATA7__SD3_DATA7 0x5a
MX7D_PAD_SD3_STROBE__SD3_STROBE 0x1a
>;
};
pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
fsl,pins = <
MX7D_PAD_SD3_CMD__SD3_CMD 0x5b
MX7D_PAD_SD3_CLK__SD3_CLK 0x1b
MX7D_PAD_SD3_DATA0__SD3_DATA0 0x5b
MX7D_PAD_SD3_DATA1__SD3_DATA1 0x5b
MX7D_PAD_SD3_DATA2__SD3_DATA2 0x5b
MX7D_PAD_SD3_DATA3__SD3_DATA3 0x5b
MX7D_PAD_SD3_DATA4__SD3_DATA4 0x5b
MX7D_PAD_SD3_DATA5__SD3_DATA5 0x5b
MX7D_PAD_SD3_DATA6__SD3_DATA6 0x5b
MX7D_PAD_SD3_DATA7__SD3_DATA7 0x5b
MX7D_PAD_SD3_STROBE__SD3_STROBE 0x1b
>;
};
};
};
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
pmic: pfuze3000@08 {
compatible = "fsl,pfuze3000";
reg = <0x08>;
regulators {
sw1a_reg: sw1a {
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <6250>;
};
/* use sw1c_reg to align with pfuze100/pfuze200 */
sw1c_reg: sw1b {
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1475000>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <6250>;
};
sw2_reg: sw2 {
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1850000>;
regulator-boot-on;
regulator-always-on;
};
sw3a_reg: sw3 {
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1650000>;
regulator-boot-on;
regulator-always-on;
};
swbst_reg: swbst {
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5150000>;
};
snvs_reg: vsnvs {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <3000000>;
regulator-boot-on;
regulator-always-on;
};
vref_reg: vrefddr {
regulator-boot-on;
regulator-always-on;
};
vgen1_reg: vldo1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vgen2_reg: vldo2 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1550000>;
regulator-always-on;
};
vgen3_reg: vccsd {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vgen4_reg: v33 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vgen5_reg: vldo3 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vgen6_reg: vldo4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
};
};
};
&i2c2 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
};
&i2c3 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
};
&i2c4 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c4>;
status = "okay";
};
&usdhc1 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_usdhc1_gpio>;
pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_usdhc1_gpio>;
cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
vmmc-supply = <&reg_sd1_vmmc>;
fsl,tuning-start-tap = <20>;
fsl,tuning-step= <2>;
status = "okay";
};
&usdhc2 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc2>;
pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
non-removable;
fsl,tuning-start-tap = <20>;
fsl,tuning-step= <2>;
status = "okay";
};
&usdhc3 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc3>;
pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
bus-width = <8>;
non-removable;
fsl,tuning-start-tap = <20>;
fsl,tuning-step= <2>;
status = "okay";
};