blob: e017d8b55895ba79328dd9281458e35a99b5900a [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2015-2018 NXP
* Copyright 2014 Freescale Semiconductor, Inc.
*
*/
#ifndef __FSL_STREAM_ID_H
#define __FSL_STREAM_ID_H
/*
* Stream IDs on NXP Chassis-3 (for example ls2080a, ls1088a, ls2088a)
* devices are not hardwired and are programmed by sw. There are a limited
* number of stream IDs available, and the partitioning of them is scenario
* dependent. This header defines the partitioning between legacy,
* PCI, and DPAA2 devices.
*
* This partitioning can be customized in this file depending
* on the specific hardware config:
*
* -non-PCI legacy, platform devices (USB, SD/MMC, SATA, DMA)
* -all legacy devices get a unique stream ID assigned and programmed in
* their AMQR registers by u-boot
*
* -PCIe
* -there is a range of stream IDs set aside for PCI in this
* file. U-boot will scan the PCI bus and for each device discovered:
* -allocate a streamID
* -set a PEXn LUT table entry mapping 'requester ID' to 'stream ID'
* -set a msi-map entry in the PEXn controller node in the
* device tree (see Documentation/devicetree/bindings/pci/pci-msi.txt
* for more info on the msi-map definition)
* -set a iommu-map entry in the PEXn controller node in the
* device tree (see Documentation/devicetree/bindings/pci/pci-iommu.txt
* for more info on the iommu-map definition)
*
* -DPAA2
* -u-boot will allocate a range of stream IDs to be used by the Management
* Complex for containers and will set these values in the MC DPC image.
* -u-boot will fixup the iommu-map property in the fsl-mc node in the
* device tree (see Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt
* for more info on the msi-map definition)
* -the MC is responsible for allocating and setting up 'isolation context
* IDs (ICIDs) based on the allocated stream IDs for all DPAA2 devices.
*
* On Chasis-3 SoCs stream IDs are programmed in AMQ registers (32-bits) for
* each of the different bus masters. The relationship between
* the AMQ registers and stream IDs is defined in the table below:
* AMQ bit streamID bit
* ---------------------------
* PL[18] 9 // privilege bit
* BMT[17] 8 // bypass translation
* VA[16] 7 // reserved
* [15] - // unused
* ICID[14:7] - // unused
* ICID[6:0] 6-0 // isolation context id
* ----------------------------
*
*/
#define AMQ_PL_MASK (0x1 << 18) /* priviledge bit */
#define AMQ_BMT_MASK (0x1 << 17) /* bypass bit */
#define FSL_INVALID_STREAM_ID 0
#define FSL_BYPASS_AMQ (AMQ_PL_MASK | AMQ_BMT_MASK)
/* legacy devices */
#define FSL_USB1_STREAM_ID 1
#define FSL_USB2_STREAM_ID 2
#define FSL_SDMMC_STREAM_ID 3
#define FSL_SATA1_STREAM_ID 4
#if defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LX2160A)
#define FSL_SATA2_STREAM_ID 5
#endif
#if defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LX2160A)
#define FSL_DMA_STREAM_ID 6
#elif defined(CONFIG_ARCH_LS1088A)
#define FSL_DMA_STREAM_ID 5
#endif
/* PCI - programmed in PEXn_LUT */
#define FSL_PEX_STREAM_ID_START 7
#ifdef CONFIG_ARCH_LX2160A
#define FSL_PEX_STREAM_ID_NUM (0x100)
#endif
#if defined(CONFIG_ARCH_LS2080A)
#define FSL_PEX_STREAM_ID_END 22
#elif defined(CONFIG_ARCH_LS1088A)
#define FSL_PEX_STREAM_ID_END 18
#endif
/* DPAA2 - set in MC DPC and alloced by MC */
#define FSL_DPAA2_STREAM_ID_START 23
#define FSL_DPAA2_STREAM_ID_END 63
#endif