| # |
| # Copyright (c) 2012 Michael Walle |
| # Michael Walle <michael@walle.cc> |
| # |
| # SPDX-License-Identifier: GPL-2.0+ |
| # |
| # Refer doc/README.kwbimage for more details about how-to configure |
| # and create kirkwood boot image |
| # |
| |
| # Boot Media configurations |
| BOOT_FROM spi |
| |
| # SOC registers configuration using bootrom header extension |
| # Maximum KWBIMAGE_MAX_CONFIG configurations allowed |
| |
| # Configure RGMII-0/1 interface pad voltage to 1.8V |
| DATA 0xFFD100E0 0x1B1B9B9B |
| |
| # L2 RAM Timing 0 |
| DATA 0xFFD20134 0xBBBBBBBB |
| # not further specified in HW manual, timing taken from original vendor port |
| |
| # L2 RAM Timing 1 |
| DATA 0xFFD20138 0x00BBBBBB |
| # not further specified in HW manual, timing taken from original vendor port |
| |
| # DDR Configuration register |
| DATA 0xFFD01400 0x43000618 |
| # bit13-0: 0x618, 1560 DDR2 clks refresh rate |
| # bit23-14: 0 required |
| # bit24: 1, enable exit self refresh mode on DDR access |
| # bit25: 1 required |
| # bit29-26: 0 required |
| # bit31-30: 0b01 required |
| |
| # DDR Controller Control Low |
| DATA 0xFFD01404 0x39543010 |
| # bit3-0: 0 required |
| # bit4: 1, T2 mode, addr/cmd are driven for two cycles |
| # bit5: 0, clk is driven during self refresh, we don't care for APX |
| # bit6: 0, use recommended falling edge of clk for addr/cmd |
| # bit11-7: 0 required |
| # bit12: 1 required |
| # bit13: 1 required |
| # bit14: 0, input buffer always powered up |
| # bit17-15: 0 required |
| # bit18: 1, cpu lock transaction enabled |
| # bit19: 0 required |
| # bit23-20: 5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 |
| # bit27-24: 9, CL+4, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM |
| # bit30-28: 3 required |
| # bit31: 0, no additional STARTBURST delay |
| |
| # DDR Timing (Low) |
| DATA 0xFFD01408 0x22125441 |
| # bit3-0: 0x1, 18 cycle tRAS (tRAS[3-0]) |
| # bit7-4: 4, 5 cycle tRCD |
| # bit11-8: 4, 5 cyle tRP |
| # bit15-12: 5, 6 cyle tWR |
| # bit19-16: 2, 3 cyle tWTR |
| # bit20: 1, 18 cycle tRAS (tRAS[4]) |
| # bit23-21: 0 required |
| # bit27-24: 2, 3 cycle tRRD |
| # bit31-28: 2, 3 cyle tRTP |
| |
| # DDR Timing (High) |
| DATA 0xFFD0140C 0x00000832 |
| # bit6-0: 0x32, 50 cycle tRFC |
| # bit8-7: 0, 1 cycle tR2R |
| # bit10-9: 0, 1 cyle tR2W |
| # bit12-11: 1, 2 cylce tW2W |
| # bit31-13: 0 required |
| |
| # DDR Address Control |
| DATA 0xFFD01410 0x0000000C |
| # bit1-0: 0, Cs0width=x8 |
| # bit3-2: 3, Cs0size=1Gbit |
| # bit5-4: 0, Cs1width=nonexistent |
| # bit7-6: 0, Cs1size=nonexistent |
| # bit9-8: 0, Cs2width=nonexistent |
| # bit11-10: 0, Cs2size=nonexistent |
| # bit13-12: 0, Cs3width=nonexistent |
| # bit15-14: 0, Cs3size=nonexistent |
| # bit16: 0, Cs0AddrSel |
| # bit17: 0, Cs1AddrSel |
| # bit18: 0, Cs2AddrSel |
| # bit19: 0, Cs3AddrSel |
| # bit31-20: 0 required |
| |
| # DDR Open Pages Control |
| DATA 0xFFD01414 0x00000000 |
| # bit0: 0, OPEn=OpenPage enabled |
| # bit31-1: 0 required |
| |
| # DDR Operation |
| DATA 0xFFD01418 0x00000000 |
| # bit3-0: 0, Cmd=Normal SDRAM Mode |
| # bit31-4: 0 required |
| |
| # DDR Mode |
| DATA 0xFFD0141C 0x00000652 |
| # bit2-0: 2, Burst Length (2 required) |
| # bit3: 0, Burst Type (0 required) |
| # bit6-4: 5, CAS Latency (CL) 5 |
| # bit7: 0, (Test Mode) Normal operation |
| # bit8: 0, (Reset DLL) Normal operation |
| # bit11-9: 3, Write recovery for auto-precharge (3 required) |
| # bit12: 0, Fast Active power down exit time (0 required) |
| # bit31-13: 0 required |
| |
| # DDR Extended Mode |
| DATA 0xFFD01420 0x00000006 |
| # bit0: 0, DRAM DLL enabled |
| # bit1: 1, DRAM drive strength reduced |
| # bit2: 1, ODT control Rtt[0] (Rtt=1, 75 ohm termination) |
| # bit5-3: 0 required |
| # bit6: 0, ODT control Rtt[1] (Rtt=1, 75 ohm termination) |
| # bit9-7: 0 required |
| # bit10: 0, differential DQS enabled |
| # bit11: 0 required |
| # bit12: 0, DRAM output buffer enabled |
| # bit31-13: 0 required |
| |
| # DDR Controller Control High |
| DATA 0xFFD01424 0x0000F17F |
| # bit2-0: 0x7 required |
| # bit3: 1, MBUS Burst Chop disabled |
| # bit6-4: 0x7 required |
| # bit7: 0 required (???) |
| # bit8: 1, add writepath sample stage, must be 1 for DDR freq >= 300MHz |
| # bit9: 0, no half clock cycle addition to dataout |
| # bit10: 0, 1/4 clock cycle skew enabled for addr/ctl signals |
| # bit11: 0, 1/4 clock cycle skew disabled for write mesh |
| # bit15-12: 0xf required |
| # bit31-16: 0 required |
| |
| # DDR2 ODT Read Timing (default values) |
| DATA 0xFFD01428 0x00085520 |
| # bit3-0: 0 required |
| # bit7-4: 2, 2 cycles from read command to assertion of M_ODT signal |
| # bit11-8: 5, 5 cycles from read command to de-assertion of M_ODT signal |
| # bit15-12: 5, 5 cycles from read command to assertion of internal ODT signal |
| # bit19-16: 8, 8 cycles from read command to de-assertion of internal ODT signal |
| # bit31-20: 0 required |
| |
| # DDR2 ODT Write Timing (default values) |
| DATA 0xFFD0147C 0x00008552 |
| # bit3-0: 2, 2 cycles from write comand to assertion of M_ODT signal |
| # bit7-4: 5, 5 cycles from write command to de-assertion of M_ODT signal |
| # bit15-12: 5, 5 cycles from write command to assertion of internal ODT signal |
| # bit19-16: 8, 8 cycles from write command to de-assertion of internal ODT signal |
| # bit31-16: 0 required |
| |
| # CS[0]n Base address |
| DATA 0xFFD01500 0x00000000 |
| # at 0x0 |
| |
| # CS[0]n Size |
| DATA 0xFFD01504 0x0FFFFFF1 |
| # bit0: 1, Window enabled |
| # bit1: 0, Write Protect disabled |
| # bit3-2: 0x0, CS0 hit selected |
| # bit23-4: 0xfffff required |
| # bit31-24: 0x0f, Size (i.e. 256MB) |
| |
| # CS[1]n Size |
| DATA 0xFFD0150C 0x00000000 |
| # window disabled |
| |
| # CS[2]n Size |
| DATA 0xFFD01514 0x00000000 |
| # window disabled |
| |
| # CS[3]n Size |
| DATA 0xFFD0151C 0x00000000 |
| # window disabled |
| |
| # DDR ODT Control (Low) |
| DATA 0xFFD01494 0x00010000 |
| # bit3-0: 0b0000, (read) M_ODT[0] is not asserted during read from DRAM |
| # bit7-4: 0b0000, (read) M_ODT[1] is not asserted during read from DRAM |
| # bit15-8: 0 required |
| # bit19-16: 0b0001, (write) M_ODT[0] is asserted during write to DRAM CS0 |
| # bit23-20: 0b0000, (write) M_ODT[1] is not asserted during write to DRAM |
| # bit31-24: 0 required |
| |
| # DDR ODT Control (High) |
| DATA 0xFFD01498 0x00000000 |
| # bit1-0: 0, M_ODT[0] assertion is controlled by ODT Control Low register |
| # bit3-2: 0, M_ODT[1] assertion is controlled by ODT Control Low register |
| # bit31-4 0 required |
| |
| # CPU ODT Control |
| DATA 0xFFD0149C 0x0000E80F |
| # bit3-0: 0b1111, internal ODT is asserted during read from DRAM bank 0-3 |
| # bit7-4: 0b0000, internal ODT is not asserted during write to DRAM bank 0-3 |
| # bit9-8: 0, Internal ODT assertion is controlled by fiels |
| # bit11-10: 2, M_DQ, M_DM, and M_DQS I/O buffer ODT 75 ohm |
| # bit13-12: 2, M_STARTBURST_IN I/O buffer ODT 75 ohm |
| # bit14: 1, M_STARTBURST_IN ODT enabled |
| # bit15: 1, DDR IO ODT Unit: Drive ODT calibration values |
| # bit20-16: 0, Pad N channel driving strength for ODT |
| # bit25-21: 0, Pad P channel driving strength for ODT |
| # bit31-26: 0 required |
| |
| # DDR Initialization Control |
| DATA 0xFFD01480 0x00000001 |
| # bit0: 1, enable DDR init upon this register write |
| # bit31-1: 0, required |
| |
| # End of Header extension |
| DATA 0x0 0x0 |
