drivers/net/xilinx_axi_emac.c - manifest_repos/u-boot - Git at Google

 /*
  * Copyright (C) 2011 Michal Simek <monstr@monstr.eu>
  * Copyright (C) 2011 PetaLogix
  * Copyright (C) 2010 Xilinx, Inc. All rights reserved.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #include <config.h>
 #include <common.h>
 #include <net.h>
 #include <malloc.h>
 #include <asm/io.h>
 #include <phy.h>
 #include <miiphy.h>

 #if !defined(CONFIG_PHYLIB)
 # error AXI_ETHERNET requires PHYLIB
 #endif

 /* Link setup */
 #define XAE_EMMC_LINKSPEED_MASK	0xC0000000 /* Link speed */
 #define XAE_EMMC_LINKSPD_10	0x00000000 /* Link Speed mask for 10 Mbit */
 #define XAE_EMMC_LINKSPD_100	0x40000000 /* Link Speed mask for 100 Mbit */
 #define XAE_EMMC_LINKSPD_1000	0x80000000 /* Link Speed mask for 1000 Mbit */

 /* Interrupt Status/Enable/Mask Registers bit definitions */
 #define XAE_INT_RXRJECT_MASK	0x00000008 /* Rx frame rejected */
 #define XAE_INT_MGTRDY_MASK	0x00000080 /* MGT clock Lock */

 /* Receive Configuration Word 1 (RCW1) Register bit definitions */
 #define XAE_RCW1_RX_MASK	0x10000000 /* Receiver enable */

 /* Transmitter Configuration (TC) Register bit definitions */
 #define XAE_TC_TX_MASK		0x10000000 /* Transmitter enable */

 #define XAE_UAW1_UNICASTADDR_MASK	0x0000FFFF

 /* MDIO Management Configuration (MC) Register bit definitions */
 #define XAE_MDIO_MC_MDIOEN_MASK		0x00000040 /* MII management enable*/

 /* MDIO Management Control Register (MCR) Register bit definitions */
 #define XAE_MDIO_MCR_PHYAD_MASK		0x1F000000 /* Phy Address Mask */
 #define XAE_MDIO_MCR_PHYAD_SHIFT	24	   /* Phy Address Shift */
 #define XAE_MDIO_MCR_REGAD_MASK		0x001F0000 /* Reg Address Mask */
 #define XAE_MDIO_MCR_REGAD_SHIFT	16	   /* Reg Address Shift */
 #define XAE_MDIO_MCR_OP_READ_MASK	0x00008000 /* Op Code Read Mask */
 #define XAE_MDIO_MCR_OP_WRITE_MASK	0x00004000 /* Op Code Write Mask */
 #define XAE_MDIO_MCR_INITIATE_MASK	0x00000800 /* Ready Mask */
 #define XAE_MDIO_MCR_READY_MASK		0x00000080 /* Ready Mask */

 #define XAE_MDIO_DIV_DFT	29	/* Default MDIO clock divisor */

 /* DMA macros */
 /* Bitmasks of XAXIDMA_CR_OFFSET register */
 #define XAXIDMA_CR_RUNSTOP_MASK	0x00000001 /* Start/stop DMA channel */
 #define XAXIDMA_CR_RESET_MASK	0x00000004 /* Reset DMA engine */

 /* Bitmasks of XAXIDMA_SR_OFFSET register */
 #define XAXIDMA_HALTED_MASK	0x00000001  /* DMA channel halted */

 /* Bitmask for interrupts */
 #define XAXIDMA_IRQ_IOC_MASK	0x00001000 /* Completion intr */
 #define XAXIDMA_IRQ_DELAY_MASK	0x00002000 /* Delay interrupt */
 #define XAXIDMA_IRQ_ALL_MASK	0x00007000 /* All interrupts */

 /* Bitmasks of XAXIDMA_BD_CTRL_OFFSET register */
 #define XAXIDMA_BD_CTRL_TXSOF_MASK	0x08000000 /* First tx packet */
 #define XAXIDMA_BD_CTRL_TXEOF_MASK	0x04000000 /* Last tx packet */

 #define DMAALIGN	128

 static u8 rxframe[PKTSIZE_ALIGN] __attribute((aligned(DMAALIGN)));

 /* Reflect dma offsets */
 struct axidma_reg {
 	u32 control; /* DMACR */
 	u32 status; /* DMASR */
 	u32 current; /* CURDESC */
 	u32 reserved;
 	u32 tail; /* TAILDESC */
 };

 /* Private driver structures */
 struct axidma_priv {
 	struct axidma_reg *dmatx;
 	struct axidma_reg *dmarx;
 	int phyaddr;

 	struct phy_device *phydev;
 	struct mii_dev *bus;
 };

 /* BD descriptors */
 struct axidma_bd {
 	u32 next;	/* Next descriptor pointer */
 	u32 reserved1;
 	u32 phys;	/* Buffer address */
 	u32 reserved2;
 	u32 reserved3;
 	u32 reserved4;
 	u32 cntrl;	/* Control */
 	u32 status;	/* Status */
 	u32 app0;
 	u32 app1;	/* TX start << 16 | insert */
 	u32 app2;	/* TX csum seed */
 	u32 app3;
 	u32 app4;
 	u32 sw_id_offset;
 	u32 reserved5;
 	u32 reserved6;
 };

 /* Static BDs - driver uses only one BD */
 static struct axidma_bd tx_bd __attribute((aligned(DMAALIGN)));
 static struct axidma_bd rx_bd __attribute((aligned(DMAALIGN)));

 struct axi_regs {
 	u32 reserved[3];
 	u32 is; /* 0xC: Interrupt status */
 	u32 reserved2;
 	u32 ie; /* 0x14: Interrupt enable */
 	u32 reserved3[251];
 	u32 rcw1; /* 0x404: Rx Configuration Word 1 */
 	u32 tc; /* 0x408: Tx Configuration */
 	u32 reserved4;
 	u32 emmc; /* 0x410: EMAC mode configuration */
 	u32 reserved5[59];
 	u32 mdio_mc; /* 0x500: MII Management Config */
 	u32 mdio_mcr; /* 0x504: MII Management Control */
 	u32 mdio_mwd; /* 0x508: MII Management Write Data */
 	u32 mdio_mrd; /* 0x50C: MII Management Read Data */
 	u32 reserved6[124];
 	u32 uaw0; /* 0x700: Unicast address word 0 */
 	u32 uaw1; /* 0x704: Unicast address word 1 */
 };

 /* Use MII register 1 (MII status register) to detect PHY */
 #define PHY_DETECT_REG  1

 /*
  * Mask used to verify certain PHY features (or register contents)
  * in the register above:
  *  0x1000: 10Mbps full duplex support
  *  0x0800: 10Mbps half duplex support
  *  0x0008: Auto-negotiation support
  */
 #define PHY_DETECT_MASK 0x1808

 static inline int mdio_wait(struct eth_device *dev)
 {
 	struct axi_regs *regs = (struct axi_regs *)dev->iobase;
 	u32 timeout = 200;

 	/* Wait till MDIO interface is ready to accept a new transaction. */
 	while (timeout && (!(in_be32(&regs->mdio_mcr)
 						& XAE_MDIO_MCR_READY_MASK))) {
 		timeout--;
 		udelay(1);
 	}
 	if (!timeout) {
 		printf("%s: Timeout\n", __func__);
 		return 1;
 	}
 	return 0;
 }

 static u32 phyread(struct eth_device *dev, u32 phyaddress, u32 registernum,
 								u16 *val)
 {
 	struct axi_regs *regs = (struct axi_regs *)dev->iobase;
 	u32 mdioctrlreg = 0;

 	if (mdio_wait(dev))
 		return 1;

 	mdioctrlreg = ((phyaddress << XAE_MDIO_MCR_PHYAD_SHIFT) &
 			XAE_MDIO_MCR_PHYAD_MASK) |
 			((registernum << XAE_MDIO_MCR_REGAD_SHIFT)
 			& XAE_MDIO_MCR_REGAD_MASK) |
 			XAE_MDIO_MCR_INITIATE_MASK |
 			XAE_MDIO_MCR_OP_READ_MASK;

 	out_be32(&regs->mdio_mcr, mdioctrlreg);

 	if (mdio_wait(dev))
 		return 1;

 	/* Read data */
 	*val = in_be32(&regs->mdio_mrd);
 	return 0;
 }

 static u32 phywrite(struct eth_device *dev, u32 phyaddress, u32 registernum,
 								u32 data)
 {
 	struct axi_regs *regs = (struct axi_regs *)dev->iobase;
 	u32 mdioctrlreg = 0;

 	if (mdio_wait(dev))
 		return 1;

 	mdioctrlreg = ((phyaddress << XAE_MDIO_MCR_PHYAD_SHIFT) &
 			XAE_MDIO_MCR_PHYAD_MASK) |
 			((registernum << XAE_MDIO_MCR_REGAD_SHIFT)
 			& XAE_MDIO_MCR_REGAD_MASK) |
 			XAE_MDIO_MCR_INITIATE_MASK |
 			XAE_MDIO_MCR_OP_WRITE_MASK;

 	/* Write data */
 	out_be32(&regs->mdio_mwd, data);

 	out_be32(&regs->mdio_mcr, mdioctrlreg);

 	if (mdio_wait(dev))
 		return 1;

 	return 0;
 }

 /* Setting axi emac and phy to proper setting */
 static int setup_phy(struct eth_device *dev)
 {
 	u16 phyreg;
 	u32 i, speed, emmc_reg, ret;
 	struct axidma_priv *priv = dev->priv;
 	struct axi_regs *regs = (struct axi_regs *)dev->iobase;
 	struct phy_device *phydev;

 	u32 supported = SUPPORTED_10baseT_Half |
 			SUPPORTED_10baseT_Full |
 			SUPPORTED_100baseT_Half |
 			SUPPORTED_100baseT_Full |
 			SUPPORTED_1000baseT_Half |
 			SUPPORTED_1000baseT_Full;

 	if (priv->phyaddr == -1) {
 		/* Detect the PHY address */
 		for (i = 31; i >= 0; i--) {
 			ret = phyread(dev, i, PHY_DETECT_REG, &phyreg);
 			if (!ret && (phyreg != 0xFFFF) &&
 			((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
 				/* Found a valid PHY address */
 				priv->phyaddr = i;
 				debug("axiemac: Found valid phy address, %x\n",
 									phyreg);
 				break;
 			}
 		}
 	}

 	/* Interface - look at tsec */
 	phydev = phy_connect(priv->bus, priv->phyaddr, dev, 0);

 	phydev->supported &= supported;
 	phydev->advertising = phydev->supported;
 	priv->phydev = phydev;
 	phy_config(phydev);
 	if (phy_startup(phydev)) {
 		printf("axiemac: could not initialize PHY %s\n",
 		       phydev->dev->name);
 		return 0;
 	}
 	if (!phydev->link) {
 		printf("%s: No link.\n", phydev->dev->name);
 		return 0;
 	}

 	switch (phydev->speed) {
 	case 1000:
 		speed = XAE_EMMC_LINKSPD_1000;
 		break;
 	case 100:
 		speed = XAE_EMMC_LINKSPD_100;
 		break;
 	case 10:
 		speed = XAE_EMMC_LINKSPD_10;
 		break;
 	default:
 		return 0;
 	}

 	/* Setup the emac for the phy speed */
 	emmc_reg = in_be32(&regs->emmc);
 	emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK;
 	emmc_reg |= speed;

 	/* Write new speed setting out to Axi Ethernet */
 	out_be32(&regs->emmc, emmc_reg);

 	/*
 	* Setting the operating speed of the MAC needs a delay. There
 	* doesn't seem to be register to poll, so please consider this
 	* during your application design.
 	*/
 	udelay(1);

 	return 1;
 }

 /* STOP DMA transfers */
 static void axiemac_halt(struct eth_device *dev)
 {
 	struct axidma_priv *priv = dev->priv;
 	u32 temp;

 	/* Stop the hardware */
 	temp = in_be32(&priv->dmatx->control);
 	temp &= ~XAXIDMA_CR_RUNSTOP_MASK;
 	out_be32(&priv->dmatx->control, temp);

 	temp = in_be32(&priv->dmarx->control);
 	temp &= ~XAXIDMA_CR_RUNSTOP_MASK;
 	out_be32(&priv->dmarx->control, temp);

 	debug("axiemac: Halted\n");
 }

 static int axi_ethernet_init(struct eth_device *dev)
 {
 	struct axi_regs *regs = (struct axi_regs *)dev->iobase;
 	u32 timeout = 200;

 	/*
 	 * Check the status of the MgtRdy bit in the interrupt status
 	 * registers. This must be done to allow the MGT clock to become stable
 	 * for the Sgmii and 1000BaseX PHY interfaces. No other register reads
 	 * will be valid until this bit is valid.
 	 * The bit is always a 1 for all other PHY interfaces.
 	 */
 	while (timeout && (!(in_be32(&regs->is) & XAE_INT_MGTRDY_MASK))) {
 		timeout--;
 		udelay(1);
 	}
 	if (!timeout) {
 		printf("%s: Timeout\n", __func__);
 		return 1;
 	}

 	/* Stop the device and reset HW */
 	/* Disable interrupts */
 	out_be32(&regs->ie, 0);

 	/* Disable the receiver */
 	out_be32(&regs->rcw1, in_be32(&regs->rcw1) & ~XAE_RCW1_RX_MASK);

 	/*
 	 * Stopping the receiver in mid-packet causes a dropped packet
 	 * indication from HW. Clear it.
 	 */
 	/* Set the interrupt status register to clear the interrupt */
 	out_be32(&regs->is, XAE_INT_RXRJECT_MASK);

 	/* Setup HW */
 	/* Set default MDIO divisor */
 	out_be32(&regs->mdio_mc, XAE_MDIO_DIV_DFT | XAE_MDIO_MC_MDIOEN_MASK);

 	debug("axiemac: InitHw done\n");
 	return 0;
 }

 static int axiemac_setup_mac(struct eth_device *dev)
 {
 	struct axi_regs *regs = (struct axi_regs *)dev->iobase;

 	/* Set the MAC address */
 	int val = ((dev->enetaddr[3] << 24) | (dev->enetaddr[2] << 16) |
 		(dev->enetaddr[1] << 8) | (dev->enetaddr[0]));
 	out_be32(&regs->uaw0, val);

 	val = (dev->enetaddr[5] << 8) | dev->enetaddr[4] ;
 	val |= in_be32(&regs->uaw1) & ~XAE_UAW1_UNICASTADDR_MASK;
 	out_be32(&regs->uaw1, val);
 	return 0;
 }

 /* Reset DMA engine */
 static void axi_dma_init(struct eth_device *dev)
 {
 	struct axidma_priv *priv = dev->priv;
 	u32 timeout = 500;

 	/* Reset the engine so the hardware starts from a known state */
 	out_be32(&priv->dmatx->control, XAXIDMA_CR_RESET_MASK);
 	out_be32(&priv->dmarx->control, XAXIDMA_CR_RESET_MASK);

 	/* At the initialization time, hardware should finish reset quickly */
 	while (timeout--) {
 		/* Check transmit/receive channel */
 		/* Reset is done when the reset bit is low */
 		if (!(in_be32(&priv->dmatx->control) |
 				in_be32(&priv->dmarx->control))
 						& XAXIDMA_CR_RESET_MASK) {
 			break;
 		}
 	}
 	if (!timeout)
 		printf("%s: Timeout\n", __func__);
 }

 static int axiemac_init(struct eth_device *dev, bd_t * bis)
 {
 	struct axidma_priv *priv = dev->priv;
 	struct axi_regs *regs = (struct axi_regs *)dev->iobase;
 	u32 temp;

 	debug("axiemac: Init started\n");
 	/*
 	 * Initialize AXIDMA engine. AXIDMA engine must be initialized before
 	 * AxiEthernet. During AXIDMA engine initialization, AXIDMA hardware is
 	 * reset, and since AXIDMA reset line is connected to AxiEthernet, this
 	 * would ensure a reset of AxiEthernet.
 	 */
 	axi_dma_init(dev);

 	/* Initialize AxiEthernet hardware. */
 	if (axi_ethernet_init(dev))
 		return -1;

 	/* Disable all RX interrupts before RxBD space setup */
 	temp = in_be32(&priv->dmarx->control);
 	temp &= ~XAXIDMA_IRQ_ALL_MASK;
 	out_be32(&priv->dmarx->control, temp);

 	/* Start DMA RX channel. Now it's ready to receive data.*/
 	out_be32(&priv->dmarx->current, (u32)&rx_bd);

 	/* Setup the BD. */
 	memset(&rx_bd, 0, sizeof(rx_bd));
 	rx_bd.next = (u32)&rx_bd;
 	rx_bd.phys = (u32)&rxframe;
 	rx_bd.cntrl = sizeof(rxframe);
 	/* Flush the last BD so DMA core could see the updates */
 	flush_cache((u32)&rx_bd, sizeof(rx_bd));

 	/* It is necessary to flush rxframe because if you don't do it
 	 * then cache can contain uninitialized data */
 	flush_cache((u32)&rxframe, sizeof(rxframe));

 	/* Start the hardware */
 	temp = in_be32(&priv->dmarx->control);
 	temp |= XAXIDMA_CR_RUNSTOP_MASK;
 	out_be32(&priv->dmarx->control, temp);

 	/* Rx BD is ready - start */
 	out_be32(&priv->dmarx->tail, (u32)&rx_bd);

 	/* Enable TX */
 	out_be32(&regs->tc, XAE_TC_TX_MASK);
 	/* Enable RX */
 	out_be32(&regs->rcw1, XAE_RCW1_RX_MASK);

 	/* PHY setup */
 	if (!setup_phy(dev)) {
 		axiemac_halt(dev);
 		return -1;
 	}

 	debug("axiemac: Init complete\n");
 	return 0;
 }

 static int axiemac_send(struct eth_device *dev, void *ptr, int len)
 {
 	struct axidma_priv *priv = dev->priv;
 	u32 timeout;

 	if (len > PKTSIZE_ALIGN)
 		len = PKTSIZE_ALIGN;

 	/* Flush packet to main memory to be trasfered by DMA */
 	flush_cache((u32)ptr, len);

 	/* Setup Tx BD */
 	memset(&tx_bd, 0, sizeof(tx_bd));
 	/* At the end of the ring, link the last BD back to the top */
 	tx_bd.next = (u32)&tx_bd;
 	tx_bd.phys = (u32)ptr;
 	/* Save len */
 	tx_bd.cntrl = len | XAXIDMA_BD_CTRL_TXSOF_MASK |
 						XAXIDMA_BD_CTRL_TXEOF_MASK;

 	/* Flush the last BD so DMA core could see the updates */
 	flush_cache((u32)&tx_bd, sizeof(tx_bd));

 	if (in_be32(&priv->dmatx->status) & XAXIDMA_HALTED_MASK) {
 		u32 temp;
 		out_be32(&priv->dmatx->current, (u32)&tx_bd);
 		/* Start the hardware */
 		temp = in_be32(&priv->dmatx->control);
 		temp |= XAXIDMA_CR_RUNSTOP_MASK;
 		out_be32(&priv->dmatx->control, temp);
 	}

 	/* Start transfer */
 	out_be32(&priv->dmatx->tail, (u32)&tx_bd);

 	/* Wait for transmission to complete */
 	debug("axiemac: Waiting for tx to be done\n");
 	timeout = 200;
 	while (timeout && (!in_be32(&priv->dmatx->status) &
 			(XAXIDMA_IRQ_DELAY_MASK | XAXIDMA_IRQ_IOC_MASK))) {
 		timeout--;
 		udelay(1);
 	}
 	if (!timeout) {
 		printf("%s: Timeout\n", __func__);
 		return 1;
 	}

 	debug("axiemac: Sending complete\n");
 	return 0;
 }

 static int isrxready(struct eth_device *dev)
 {
 	u32 status;
 	struct axidma_priv *priv = dev->priv;

 	/* Read pending interrupts */
 	status = in_be32(&priv->dmarx->status);

 	/* Acknowledge pending interrupts */
 	out_be32(&priv->dmarx->status, status & XAXIDMA_IRQ_ALL_MASK);

 	/*
 	 * If Reception done interrupt is asserted, call RX call back function
 	 * to handle the processed BDs and then raise the according flag.
 	 */
 	if ((status & (XAXIDMA_IRQ_DELAY_MASK | XAXIDMA_IRQ_IOC_MASK)))
 		return 1;

 	return 0;
 }

 static int axiemac_recv(struct eth_device *dev)
 {
 	u32 length;
 	struct axidma_priv *priv = dev->priv;
 	u32 temp;

 	/* Wait for an incoming packet */
 	if (!isrxready(dev))
 		return 0;

 	debug("axiemac: RX data ready\n");

 	/* Disable IRQ for a moment till packet is handled */
 	temp = in_be32(&priv->dmarx->control);
 	temp &= ~XAXIDMA_IRQ_ALL_MASK;
 	out_be32(&priv->dmarx->control, temp);

 	length = rx_bd.app4 & 0xFFFF; /* max length mask */
 #ifdef DEBUG
 	print_buffer(&rxframe, &rxframe[0], 1, length, 16);
 #endif
 	/* Pass the received frame up for processing */
 	if (length)
 		NetReceive(rxframe, length);

 #ifdef DEBUG
 	/* It is useful to clear buffer to be sure that it is consistent */
 	memset(rxframe, 0, sizeof(rxframe));
 #endif
 	/* Setup RxBD */
 	/* Clear the whole buffer and setup it again - all flags are cleared */
 	memset(&rx_bd, 0, sizeof(rx_bd));
 	rx_bd.next = (u32)&rx_bd;
 	rx_bd.phys = (u32)&rxframe;
 	rx_bd.cntrl = sizeof(rxframe);

 	/* Write bd to HW */
 	flush_cache((u32)&rx_bd, sizeof(rx_bd));

 	/* It is necessary to flush rxframe because if you don't do it
 	 * then cache will contain previous packet */
 	flush_cache((u32)&rxframe, sizeof(rxframe));

 	/* Rx BD is ready - start again */
 	out_be32(&priv->dmarx->tail, (u32)&rx_bd);

 	debug("axiemac: RX completed, framelength = %d\n", length);

 	return length;
 }

 static int axiemac_miiphy_read(const char *devname, uchar addr,
 							uchar reg, ushort *val)
 {
 	struct eth_device *dev = eth_get_dev();
 	u32 ret;

 	ret = phyread(dev, addr, reg, val);
 	debug("axiemac: Read MII 0x%x, 0x%x, 0x%x\n", addr, reg, *val);
 	return ret;
 }

 static int axiemac_miiphy_write(const char *devname, uchar addr,
 							uchar reg, ushort val)
 {
 	struct eth_device *dev = eth_get_dev();

 	debug("axiemac: Write MII 0x%x, 0x%x, 0x%x\n", addr, reg, val);
 	return phywrite(dev, addr, reg, val);
 }

 static int axiemac_bus_reset(struct mii_dev *bus)
 {
 	debug("axiemac: Bus reset\n");
 	return 0;
 }

 int xilinx_axiemac_initialize(bd_t *bis, unsigned long base_addr,
 							unsigned long dma_addr)
 {
 	struct eth_device *dev;
 	struct axidma_priv *priv;

 	dev = calloc(1, sizeof(struct eth_device));
 	if (dev == NULL)
 		return -1;

 	dev->priv = calloc(1, sizeof(struct axidma_priv));
 	if (dev->priv == NULL) {
 		free(dev);
 		return -1;
 	}
 	priv = dev->priv;

 	sprintf(dev->name, "aximac.%lx", base_addr);

 	dev->iobase = base_addr;
 	priv->dmatx = (struct axidma_reg *)dma_addr;
 	/* RX channel offset is 0x30 */
 	priv->dmarx = (struct axidma_reg *)(dma_addr + 0x30);
 	dev->init = axiemac_init;
 	dev->halt = axiemac_halt;
 	dev->send = axiemac_send;
 	dev->recv = axiemac_recv;
 	dev->write_hwaddr = axiemac_setup_mac;

 #ifdef CONFIG_PHY_ADDR
 	priv->phyaddr = CONFIG_PHY_ADDR;
 #else
 	priv->phyaddr = -1;
 #endif

 	eth_register(dev);

 #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) || defined(CONFIG_PHYLIB)
 	miiphy_register(dev->name, axiemac_miiphy_read, axiemac_miiphy_write);
 	priv->bus = miiphy_get_dev_by_name(dev->name);
 	priv->bus->reset = axiemac_bus_reset;
 #endif
 	return 1;
 }
	/*
	* Copyright (C) 2011 Michal Simek <monstr@monstr.eu>
	* Copyright (C) 2011 PetaLogix
	* Copyright (C) 2010 Xilinx, Inc. All rights reserved.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#include <config.h>
	#include <common.h>
	#include <net.h>
	#include <malloc.h>
	#include <asm/io.h>
	#include <phy.h>
	#include <miiphy.h>

	#if !defined(CONFIG_PHYLIB)
	# error AXI_ETHERNET requires PHYLIB
	#endif

	/* Link setup */
	#define XAE_EMMC_LINKSPEED_MASK 0xC0000000 /* Link speed */
	#define XAE_EMMC_LINKSPD_10 0x00000000 /* Link Speed mask for 10 Mbit */
	#define XAE_EMMC_LINKSPD_100 0x40000000 /* Link Speed mask for 100 Mbit */
	#define XAE_EMMC_LINKSPD_1000 0x80000000 /* Link Speed mask for 1000 Mbit */

	/* Interrupt Status/Enable/Mask Registers bit definitions */
	#define XAE_INT_RXRJECT_MASK 0x00000008 /* Rx frame rejected */
	#define XAE_INT_MGTRDY_MASK 0x00000080 /* MGT clock Lock */

	/* Receive Configuration Word 1 (RCW1) Register bit definitions */
	#define XAE_RCW1_RX_MASK 0x10000000 /* Receiver enable */

	/* Transmitter Configuration (TC) Register bit definitions */
	#define XAE_TC_TX_MASK 0x10000000 /* Transmitter enable */

	#define XAE_UAW1_UNICASTADDR_MASK 0x0000FFFF

	/* MDIO Management Configuration (MC) Register bit definitions */
	#define XAE_MDIO_MC_MDIOEN_MASK 0x00000040 /* MII management enable*/

	/* MDIO Management Control Register (MCR) Register bit definitions */
	#define XAE_MDIO_MCR_PHYAD_MASK 0x1F000000 /* Phy Address Mask */
	#define XAE_MDIO_MCR_PHYAD_SHIFT 24 /* Phy Address Shift */
	#define XAE_MDIO_MCR_REGAD_MASK 0x001F0000 /* Reg Address Mask */
	#define XAE_MDIO_MCR_REGAD_SHIFT 16 /* Reg Address Shift */
	#define XAE_MDIO_MCR_OP_READ_MASK 0x00008000 /* Op Code Read Mask */
	#define XAE_MDIO_MCR_OP_WRITE_MASK 0x00004000 /* Op Code Write Mask */
	#define XAE_MDIO_MCR_INITIATE_MASK 0x00000800 /* Ready Mask */
	#define XAE_MDIO_MCR_READY_MASK 0x00000080 /* Ready Mask */

	#define XAE_MDIO_DIV_DFT 29 /* Default MDIO clock divisor */

	/* DMA macros */
	/* Bitmasks of XAXIDMA_CR_OFFSET register */
	#define XAXIDMA_CR_RUNSTOP_MASK 0x00000001 /* Start/stop DMA channel */
	#define XAXIDMA_CR_RESET_MASK 0x00000004 /* Reset DMA engine */

	/* Bitmasks of XAXIDMA_SR_OFFSET register */
	#define XAXIDMA_HALTED_MASK 0x00000001 /* DMA channel halted */

	/* Bitmask for interrupts */
	#define XAXIDMA_IRQ_IOC_MASK 0x00001000 /* Completion intr */
	#define XAXIDMA_IRQ_DELAY_MASK 0x00002000 /* Delay interrupt */
	#define XAXIDMA_IRQ_ALL_MASK 0x00007000 /* All interrupts */

	/* Bitmasks of XAXIDMA_BD_CTRL_OFFSET register */
	#define XAXIDMA_BD_CTRL_TXSOF_MASK 0x08000000 /* First tx packet */
	#define XAXIDMA_BD_CTRL_TXEOF_MASK 0x04000000 /* Last tx packet */

	#define DMAALIGN 128

	static u8 rxframe[PKTSIZE_ALIGN] __attribute((aligned(DMAALIGN)));

	/* Reflect dma offsets */
	struct axidma_reg {
	u32 control; /* DMACR */
	u32 status; /* DMASR */
	u32 current; /* CURDESC */
	u32 reserved;
	u32 tail; /* TAILDESC */
	};

	/* Private driver structures */
	struct axidma_priv {
	struct axidma_reg *dmatx;
	struct axidma_reg *dmarx;
	int phyaddr;

	struct phy_device *phydev;
	struct mii_dev *bus;
	};

	/* BD descriptors */
	struct axidma_bd {
	u32 next; /* Next descriptor pointer */
	u32 reserved1;
	u32 phys; /* Buffer address */
	u32 reserved2;
	u32 reserved3;
	u32 reserved4;
	u32 cntrl; /* Control */
	u32 status; /* Status */
	u32 app0;
	u32 app1; /* TX start << 16 \| insert */
	u32 app2; /* TX csum seed */
	u32 app3;
	u32 app4;
	u32 sw_id_offset;
	u32 reserved5;
	u32 reserved6;
	};

	/* Static BDs - driver uses only one BD */
	static struct axidma_bd tx_bd __attribute((aligned(DMAALIGN)));
	static struct axidma_bd rx_bd __attribute((aligned(DMAALIGN)));

	struct axi_regs {
	u32 reserved[3];
	u32 is; /* 0xC: Interrupt status */
	u32 reserved2;
	u32 ie; /* 0x14: Interrupt enable */
	u32 reserved3[251];
	u32 rcw1; /* 0x404: Rx Configuration Word 1 */
	u32 tc; /* 0x408: Tx Configuration */
	u32 reserved4;
	u32 emmc; /* 0x410: EMAC mode configuration */
	u32 reserved5[59];
	u32 mdio_mc; /* 0x500: MII Management Config */
	u32 mdio_mcr; /* 0x504: MII Management Control */
	u32 mdio_mwd; /* 0x508: MII Management Write Data */
	u32 mdio_mrd; /* 0x50C: MII Management Read Data */
	u32 reserved6[124];
	u32 uaw0; /* 0x700: Unicast address word 0 */
	u32 uaw1; /* 0x704: Unicast address word 1 */
	};

	/* Use MII register 1 (MII status register) to detect PHY */
	#define PHY_DETECT_REG 1

	/*
	* Mask used to verify certain PHY features (or register contents)
	* in the register above:
	* 0x1000: 10Mbps full duplex support
	* 0x0800: 10Mbps half duplex support
	* 0x0008: Auto-negotiation support
	*/
	#define PHY_DETECT_MASK 0x1808

	static inline int mdio_wait(struct eth_device *dev)
	{
	struct axi_regs regs = (struct axi_regs )dev->iobase;
	u32 timeout = 200;

	/* Wait till MDIO interface is ready to accept a new transaction. */
	while (timeout && (!(in_be32(&regs->mdio_mcr)
	& XAE_MDIO_MCR_READY_MASK))) {
	timeout--;
	udelay(1);
	}
	if (!timeout) {
	printf("%s: Timeout\n", __func__);
	return 1;
	}
	return 0;
	}

	static u32 phyread(struct eth_device *dev, u32 phyaddress, u32 registernum,
	u16 *val)
	{
	struct axi_regs regs = (struct axi_regs )dev->iobase;
	u32 mdioctrlreg = 0;

	if (mdio_wait(dev))
	return 1;

	mdioctrlreg = ((phyaddress << XAE_MDIO_MCR_PHYAD_SHIFT) &
	XAE_MDIO_MCR_PHYAD_MASK) \|
	((registernum << XAE_MDIO_MCR_REGAD_SHIFT)
	& XAE_MDIO_MCR_REGAD_MASK) \|
	XAE_MDIO_MCR_INITIATE_MASK \|
	XAE_MDIO_MCR_OP_READ_MASK;

	out_be32(&regs->mdio_mcr, mdioctrlreg);

	if (mdio_wait(dev))
	return 1;

	/* Read data */
	*val = in_be32(&regs->mdio_mrd);
	return 0;
	}

	static u32 phywrite(struct eth_device *dev, u32 phyaddress, u32 registernum,
	u32 data)
	{
	struct axi_regs regs = (struct axi_regs )dev->iobase;
	u32 mdioctrlreg = 0;

	if (mdio_wait(dev))
	return 1;

	mdioctrlreg = ((phyaddress << XAE_MDIO_MCR_PHYAD_SHIFT) &
	XAE_MDIO_MCR_PHYAD_MASK) \|
	((registernum << XAE_MDIO_MCR_REGAD_SHIFT)
	& XAE_MDIO_MCR_REGAD_MASK) \|
	XAE_MDIO_MCR_INITIATE_MASK \|
	XAE_MDIO_MCR_OP_WRITE_MASK;

	/* Write data */
	out_be32(&regs->mdio_mwd, data);

	out_be32(&regs->mdio_mcr, mdioctrlreg);

	if (mdio_wait(dev))
	return 1;

	return 0;
	}

	/* Setting axi emac and phy to proper setting */
	static int setup_phy(struct eth_device *dev)
	{
	u16 phyreg;
	u32 i, speed, emmc_reg, ret;
	struct axidma_priv *priv = dev->priv;
	struct axi_regs regs = (struct axi_regs )dev->iobase;
	struct phy_device *phydev;

	u32 supported = SUPPORTED_10baseT_Half \|
	SUPPORTED_10baseT_Full \|
	SUPPORTED_100baseT_Half \|
	SUPPORTED_100baseT_Full \|
	SUPPORTED_1000baseT_Half \|
	SUPPORTED_1000baseT_Full;

	if (priv->phyaddr == -1) {
	/* Detect the PHY address */
	for (i = 31; i >= 0; i--) {
	ret = phyread(dev, i, PHY_DETECT_REG, &phyreg);
	if (!ret && (phyreg != 0xFFFF) &&
	((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
	/* Found a valid PHY address */
	priv->phyaddr = i;
	debug("axiemac: Found valid phy address, %x\n",
	phyreg);
	break;
	}
	}
	}

	/* Interface - look at tsec */
	phydev = phy_connect(priv->bus, priv->phyaddr, dev, 0);

	phydev->supported &= supported;
	phydev->advertising = phydev->supported;
	priv->phydev = phydev;
	phy_config(phydev);
	if (phy_startup(phydev)) {
	printf("axiemac: could not initialize PHY %s\n",
	phydev->dev->name);
	return 0;
	}
	if (!phydev->link) {
	printf("%s: No link.\n", phydev->dev->name);
	return 0;
	}

	switch (phydev->speed) {
	case 1000:
	speed = XAE_EMMC_LINKSPD_1000;
	break;
	case 100:
	speed = XAE_EMMC_LINKSPD_100;
	break;
	case 10:
	speed = XAE_EMMC_LINKSPD_10;
	break;
	default:
	return 0;
	}

	/* Setup the emac for the phy speed */
	emmc_reg = in_be32(&regs->emmc);
	emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK;
	emmc_reg \|= speed;

	/* Write new speed setting out to Axi Ethernet */
	out_be32(&regs->emmc, emmc_reg);

	/*
	* Setting the operating speed of the MAC needs a delay. There
	* doesn't seem to be register to poll, so please consider this
	* during your application design.
	*/
	udelay(1);

	return 1;
	}

	/* STOP DMA transfers */
	static void axiemac_halt(struct eth_device *dev)
	{
	struct axidma_priv *priv = dev->priv;
	u32 temp;

	/* Stop the hardware */
	temp = in_be32(&priv->dmatx->control);
	temp &= ~XAXIDMA_CR_RUNSTOP_MASK;
	out_be32(&priv->dmatx->control, temp);

	temp = in_be32(&priv->dmarx->control);
	temp &= ~XAXIDMA_CR_RUNSTOP_MASK;
	out_be32(&priv->dmarx->control, temp);

	debug("axiemac: Halted\n");
	}

	static int axi_ethernet_init(struct eth_device *dev)
	{
	struct axi_regs regs = (struct axi_regs )dev->iobase;
	u32 timeout = 200;

	/*
	* Check the status of the MgtRdy bit in the interrupt status
	* registers. This must be done to allow the MGT clock to become stable
	* for the Sgmii and 1000BaseX PHY interfaces. No other register reads
	* will be valid until this bit is valid.
	* The bit is always a 1 for all other PHY interfaces.
	*/
	while (timeout && (!(in_be32(&regs->is) & XAE_INT_MGTRDY_MASK))) {
	timeout--;
	udelay(1);
	}
	if (!timeout) {
	printf("%s: Timeout\n", __func__);
	return 1;
	}

	/* Stop the device and reset HW */
	/* Disable interrupts */
	out_be32(&regs->ie, 0);

	/* Disable the receiver */
	out_be32(&regs->rcw1, in_be32(&regs->rcw1) & ~XAE_RCW1_RX_MASK);

	/*
	* Stopping the receiver in mid-packet causes a dropped packet
	* indication from HW. Clear it.
	*/
	/* Set the interrupt status register to clear the interrupt */
	out_be32(&regs->is, XAE_INT_RXRJECT_MASK);

	/* Setup HW */
	/* Set default MDIO divisor */
	out_be32(&regs->mdio_mc, XAE_MDIO_DIV_DFT \| XAE_MDIO_MC_MDIOEN_MASK);

	debug("axiemac: InitHw done\n");
	return 0;
	}

	static int axiemac_setup_mac(struct eth_device *dev)
	{
	struct axi_regs regs = (struct axi_regs )dev->iobase;

	/* Set the MAC address */
	int val = ((dev->enetaddr[3] << 24) \| (dev->enetaddr[2] << 16) \|
	(dev->enetaddr[1] << 8) \| (dev->enetaddr[0]));
	out_be32(&regs->uaw0, val);

	val = (dev->enetaddr[5] << 8) \| dev->enetaddr[4] ;
	val \|= in_be32(&regs->uaw1) & ~XAE_UAW1_UNICASTADDR_MASK;
	out_be32(&regs->uaw1, val);
	return 0;
	}

	/* Reset DMA engine */
	static void axi_dma_init(struct eth_device *dev)
	{
	struct axidma_priv *priv = dev->priv;
	u32 timeout = 500;

	/* Reset the engine so the hardware starts from a known state */
	out_be32(&priv->dmatx->control, XAXIDMA_CR_RESET_MASK);
	out_be32(&priv->dmarx->control, XAXIDMA_CR_RESET_MASK);

	/* At the initialization time, hardware should finish reset quickly */
	while (timeout--) {
	/* Check transmit/receive channel */
	/* Reset is done when the reset bit is low */
	if (!(in_be32(&priv->dmatx->control) \|
	in_be32(&priv->dmarx->control))
	& XAXIDMA_CR_RESET_MASK) {
	break;
	}
	}
	if (!timeout)
	printf("%s: Timeout\n", __func__);
	}

	static int axiemac_init(struct eth_device dev, bd_t bis)
	{
	struct axidma_priv *priv = dev->priv;
	struct axi_regs regs = (struct axi_regs )dev->iobase;
	u32 temp;

	debug("axiemac: Init started\n");
	/*
	* Initialize AXIDMA engine. AXIDMA engine must be initialized before
	* AxiEthernet. During AXIDMA engine initialization, AXIDMA hardware is
	* reset, and since AXIDMA reset line is connected to AxiEthernet, this
	* would ensure a reset of AxiEthernet.
	*/
	axi_dma_init(dev);

	/* Initialize AxiEthernet hardware. */
	if (axi_ethernet_init(dev))
	return -1;

	/* Disable all RX interrupts before RxBD space setup */
	temp = in_be32(&priv->dmarx->control);
	temp &= ~XAXIDMA_IRQ_ALL_MASK;
	out_be32(&priv->dmarx->control, temp);

	/* Start DMA RX channel. Now it's ready to receive data.*/
	out_be32(&priv->dmarx->current, (u32)&rx_bd);

	/* Setup the BD. */
	memset(&rx_bd, 0, sizeof(rx_bd));
	rx_bd.next = (u32)&rx_bd;
	rx_bd.phys = (u32)&rxframe;
	rx_bd.cntrl = sizeof(rxframe);
	/* Flush the last BD so DMA core could see the updates */
	flush_cache((u32)&rx_bd, sizeof(rx_bd));

	/* It is necessary to flush rxframe because if you don't do it
	* then cache can contain uninitialized data */
	flush_cache((u32)&rxframe, sizeof(rxframe));

	/* Start the hardware */
	temp = in_be32(&priv->dmarx->control);
	temp \|= XAXIDMA_CR_RUNSTOP_MASK;
	out_be32(&priv->dmarx->control, temp);

	/* Rx BD is ready - start */
	out_be32(&priv->dmarx->tail, (u32)&rx_bd);

	/* Enable TX */
	out_be32(&regs->tc, XAE_TC_TX_MASK);
	/* Enable RX */
	out_be32(&regs->rcw1, XAE_RCW1_RX_MASK);

	/* PHY setup */
	if (!setup_phy(dev)) {
	axiemac_halt(dev);
	return -1;
	}

	debug("axiemac: Init complete\n");
	return 0;
	}

	static int axiemac_send(struct eth_device dev, void ptr, int len)
	{
	struct axidma_priv *priv = dev->priv;
	u32 timeout;

	if (len > PKTSIZE_ALIGN)
	len = PKTSIZE_ALIGN;

	/* Flush packet to main memory to be trasfered by DMA */
	flush_cache((u32)ptr, len);

	/* Setup Tx BD */
	memset(&tx_bd, 0, sizeof(tx_bd));
	/* At the end of the ring, link the last BD back to the top */
	tx_bd.next = (u32)&tx_bd;
	tx_bd.phys = (u32)ptr;
	/* Save len */
	tx_bd.cntrl = len \| XAXIDMA_BD_CTRL_TXSOF_MASK \|
	XAXIDMA_BD_CTRL_TXEOF_MASK;

	/* Flush the last BD so DMA core could see the updates */
	flush_cache((u32)&tx_bd, sizeof(tx_bd));

	if (in_be32(&priv->dmatx->status) & XAXIDMA_HALTED_MASK) {
	u32 temp;
	out_be32(&priv->dmatx->current, (u32)&tx_bd);
	/* Start the hardware */
	temp = in_be32(&priv->dmatx->control);
	temp \|= XAXIDMA_CR_RUNSTOP_MASK;
	out_be32(&priv->dmatx->control, temp);
	}

	/* Start transfer */
	out_be32(&priv->dmatx->tail, (u32)&tx_bd);

	/* Wait for transmission to complete */
	debug("axiemac: Waiting for tx to be done\n");
	timeout = 200;
	while (timeout && (!in_be32(&priv->dmatx->status) &
	(XAXIDMA_IRQ_DELAY_MASK \| XAXIDMA_IRQ_IOC_MASK))) {
	timeout--;
	udelay(1);
	}
	if (!timeout) {
	printf("%s: Timeout\n", __func__);
	return 1;
	}

	debug("axiemac: Sending complete\n");
	return 0;
	}

	static int isrxready(struct eth_device *dev)
	{
	u32 status;
	struct axidma_priv *priv = dev->priv;

	/* Read pending interrupts */
	status = in_be32(&priv->dmarx->status);

	/* Acknowledge pending interrupts */
	out_be32(&priv->dmarx->status, status & XAXIDMA_IRQ_ALL_MASK);

	/*
	* If Reception done interrupt is asserted, call RX call back function
	* to handle the processed BDs and then raise the according flag.
	*/
	if ((status & (XAXIDMA_IRQ_DELAY_MASK \| XAXIDMA_IRQ_IOC_MASK)))
	return 1;

	return 0;
	}

	static int axiemac_recv(struct eth_device *dev)
	{
	u32 length;
	struct axidma_priv *priv = dev->priv;
	u32 temp;

	/* Wait for an incoming packet */
	if (!isrxready(dev))
	return 0;

	debug("axiemac: RX data ready\n");

	/* Disable IRQ for a moment till packet is handled */
	temp = in_be32(&priv->dmarx->control);
	temp &= ~XAXIDMA_IRQ_ALL_MASK;
	out_be32(&priv->dmarx->control, temp);

	length = rx_bd.app4 & 0xFFFF; /* max length mask */
	#ifdef DEBUG
	print_buffer(&rxframe, &rxframe[0], 1, length, 16);
	#endif
	/* Pass the received frame up for processing */
	if (length)
	NetReceive(rxframe, length);

	#ifdef DEBUG
	/* It is useful to clear buffer to be sure that it is consistent */
	memset(rxframe, 0, sizeof(rxframe));
	#endif
	/* Setup RxBD */
	/* Clear the whole buffer and setup it again - all flags are cleared */
	memset(&rx_bd, 0, sizeof(rx_bd));
	rx_bd.next = (u32)&rx_bd;
	rx_bd.phys = (u32)&rxframe;
	rx_bd.cntrl = sizeof(rxframe);

	/* Write bd to HW */
	flush_cache((u32)&rx_bd, sizeof(rx_bd));

	/* It is necessary to flush rxframe because if you don't do it
	* then cache will contain previous packet */
	flush_cache((u32)&rxframe, sizeof(rxframe));

	/* Rx BD is ready - start again */
	out_be32(&priv->dmarx->tail, (u32)&rx_bd);

	debug("axiemac: RX completed, framelength = %d\n", length);

	return length;
	}

	static int axiemac_miiphy_read(const char *devname, uchar addr,
	uchar reg, ushort *val)
	{
	struct eth_device *dev = eth_get_dev();
	u32 ret;

	ret = phyread(dev, addr, reg, val);
	debug("axiemac: Read MII 0x%x, 0x%x, 0x%x\n", addr, reg, *val);
	return ret;
	}

	static int axiemac_miiphy_write(const char *devname, uchar addr,
	uchar reg, ushort val)
	{
	struct eth_device *dev = eth_get_dev();

	debug("axiemac: Write MII 0x%x, 0x%x, 0x%x\n", addr, reg, val);
	return phywrite(dev, addr, reg, val);
	}

	static int axiemac_bus_reset(struct mii_dev *bus)
	{
	debug("axiemac: Bus reset\n");
	return 0;
	}

	int xilinx_axiemac_initialize(bd_t *bis, unsigned long base_addr,
	unsigned long dma_addr)
	{
	struct eth_device *dev;
	struct axidma_priv *priv;

	dev = calloc(1, sizeof(struct eth_device));
	if (dev == NULL)
	return -1;

	dev->priv = calloc(1, sizeof(struct axidma_priv));
	if (dev->priv == NULL) {
	free(dev);
	return -1;
	}
	priv = dev->priv;

	sprintf(dev->name, "aximac.%lx", base_addr);

	dev->iobase = base_addr;
	priv->dmatx = (struct axidma_reg *)dma_addr;
	/* RX channel offset is 0x30 */
	priv->dmarx = (struct axidma_reg *)(dma_addr + 0x30);
	dev->init = axiemac_init;
	dev->halt = axiemac_halt;
	dev->send = axiemac_send;
	dev->recv = axiemac_recv;
	dev->write_hwaddr = axiemac_setup_mac;

	#ifdef CONFIG_PHY_ADDR
	priv->phyaddr = CONFIG_PHY_ADDR;
	#else
	priv->phyaddr = -1;
	#endif

	eth_register(dev);

	#if defined(CONFIG_MII) \|\| defined(CONFIG_CMD_MII) \|\| defined(CONFIG_PHYLIB)
	miiphy_register(dev->name, axiemac_miiphy_read, axiemac_miiphy_write);
	priv->bus = miiphy_get_dev_by_name(dev->name);
	priv->bus->reset = axiemac_bus_reset;
	#endif
	return 1;
	}