| /* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ |
| /* |
| * Copyright (c) 2019 Amlogic, Inc. All rights reserved. |
| */ |
| |
| #ifndef __BOARD_CFG_H__ |
| #define __BOARD_CFG_H__ |
| |
| #include <asm/arch/cpu.h> |
| #include <amlogic/base_env.h> |
| |
| /* |
| * platform power init config |
| */ |
| |
| #define AML_VCCK_A_INIT_VOLTAGE 1009 // VCCK A power up voltage |
| #define AML_VCCK_B_INIT_VOLTAGE 1009 // VCCK B power up voltage |
| #define AML_VDDEE_INIT_VOLTAGE 830 // VDDEE power up voltage |
| #define AML_VDDGPU_INIT_VOLTAGE 830 // VDDGPU power up voltage |
| #define AML_VDDNPU_INIT_VOLTAGE 830 // VDDNPU power up voltage |
| #define AML_VDDDDR_INIT_VOLTAGE 830 // VDDDDR power up voltage |
| /*Distinguish whether to use efuse to adjust vddee*/ |
| #define CONFIG_PDVFS_ENABLE |
| |
| /* SMP Definitions */ |
| #define CPU_RELEASE_ADDR secondary_boot_func |
| |
| /* Bootloader Control Block function |
| That is used for recovery and the bootloader to talk to each other |
| */ |
| #if 0 |
| #define CONFIG_BOOTLOADER_CONTROL_BLOCK |
| #endif |
| |
| /* Serial config */ |
| #define CONFIG_CONS_INDEX 2 |
| #define CONFIG_BAUDRATE 115200 |
| |
| /*low console baudrate*/ |
| #define CONFIG_LOW_CONSOLE_BAUD 0 |
| |
| /* Enable ir remote wake up for bl30 */ |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL1 0xef10fe01 //amlogic tv ir --- power |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL2 0XBB44FB04 //amlogic tv ir --- ch+ |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL3 0xF20DFE01 //amlogic tv ir --- ch- |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL4 0XBA45BD02 //amlogic small ir--- power |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL5 0xe51afb04 |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL6 0xFFFFFFFF |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL7 0xFFFFFFFF |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL8 0xFFFFFFFF |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL9 0xFFFFFFFF |
| |
| /*config the default parameters for adc power key*/ |
| #define AML_ADC_POWER_KEY_CHAN 2 /*channel range: 0-7*/ |
| #define AML_ADC_POWER_KEY_VAL 0 /*sample value range: 0-1023*/ |
| |
| //#define CONFIG_BOOTLOADER_CONTROL_BLOCK |
| |
| /* args/envs */ |
| #define CONFIG_SYS_MAXARGS 64 |
| #ifdef CONFIG_HDMITX_ONLY |
| #define CONFIG_EXTRA_HDMI_ENV_SETTINGS \ |
| "panel_type=edp_0\0" \ |
| "outputmode=1080p60hz\0" \ |
| "storeargs_hdmitx="\ |
| "setenv bootargs ${bootargs} powermode=${powermode} "\ |
| "lcd_ctrl=${lcd_ctrl} lcd_debug=${lcd_debug} "\ |
| "outputmode=${outputmode} hdmitx=${cecconfig},${colorattribute};"\ |
| "\0"\ |
| "init_display_hdmitx="\ |
| "hdmitx hpd;hdmitx get_preferred_mode;hdmitx get_parse_edid;dovi process;"\ |
| "osd open;osd clear;run load_bmp_logo;bmp scale;vout output ${outputmode};"\ |
| "dovi set;dovi pkg;vpp hdrpkt;"\ |
| "\0" |
| #else |
| #define CONFIG_EXTRA_HDMI_ENV_SETTINGS \ |
| "panel_type=vbyone_0\0" \ |
| "panel1_type=vbyone_2\0" \ |
| "panel2_type=lvds_1\0" \ |
| "lcd1_ctrl=0x00000000\0" \ |
| "lcd2_ctrl=0x00000000\0" \ |
| "outputmode=panel1\0" \ |
| "outputmode2=1080p60hz\0" \ |
| "cvbsmode=576cvbs\0" \ |
| "storeargs_hdmitx="\ |
| "setenv bootargs ${bootargs} powermode=${powermode} "\ |
| "lcd_ctrl=${lcd_ctrl} lcd_debug=${lcd_debug} "\ |
| "outputmode=${outputmode} hdmitx=${cecconfig},${colorattribute} "\ |
| "vout2=${outputmode2},enable panel1_type=${panel1_type} "\ |
| "lcd1_ctrl=${lcd1_ctrl} panel2_type=${panel2_type} lcd2_ctrl=${lcd2_ctrl} "\ |
| "hdr_policy=${hdr_policy} hdr_priority=${hdr_priority};"\ |
| "\0"\ |
| "init_display_hdmitx="\ |
| "hdmitx hpd;hdmitx get_preferred_mode;hdmitx get_parse_edid;dovi process;"\ |
| "setenv outputmode2 ${hdmimode};"\ |
| "osd dual_logo;"\ |
| "\0" |
| #endif |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_EXTRA_ENV_SETTINGS_BASE \ |
| "silent=1\0"\ |
| "loadaddr_kernel=0x01080000\0"\ |
| "dv_fw_addr=0xa00000\0"\ |
| "otg_device=1\0" \ |
| "lcd_ctrl=0x00000000\0" \ |
| "lcd_debug=0x00000000\0" \ |
| "hdmimode=none\0" \ |
| "cvbsmode=dummy_l\0" \ |
| "colorattribute=444,8bit\0"\ |
| "vout_init=enable\0" \ |
| "display_width=1920\0" \ |
| "display_height=1080\0" \ |
| "hdmichecksum=0x00000000\0" \ |
| "dv_fw_dir=/reserved/firmware/dovi_fw.bin\0" \ |
| "display_bpp=16\0" \ |
| "display_color_index=16\0" \ |
| "display_layer=osd0\0" \ |
| "display_color_fg=0xffff\0" \ |
| "display_color_bg=0\0" \ |
| "dtb_mem_addr=0x01000000\0" \ |
| "fb_addr=0x00300000\0" \ |
| "fb_width=1920\0" \ |
| "fb_height=1080\0" \ |
| "frac_rate_policy=1\0" \ |
| "hdr_policy=0\0" \ |
| "usb_burning=" CONFIG_USB_TOOL_ENTRY "\0" \ |
| "fdt_high=0x20000000\0"\ |
| "sdcburncfg=aml_sdc_burn.ini\0"\ |
| "EnableSelinux=permissive\0" \ |
| "recovery_part=recovery\0"\ |
| "lock=10101000\0"\ |
| "board=t7_an400\0"\ |
| "cvbs_drv=0\0"\ |
| "osd_reverse=0\0"\ |
| "video_reverse=0\0"\ |
| "suspend=off\0"\ |
| "powermode=on\0"\ |
| "ffv_wake=off\0"\ |
| "ffv_freeze=off\0"\ |
| "edid_14_dir=/odm/etc/tvconfig/hdmi/port1_14.bin\0" \ |
| "edid_20_dir=/odm/etc/tvconfig/hdmi/port1_20.bin\0" \ |
| "edid_select=0\0" \ |
| "port_map=0x4321\0" \ |
| "cec_fun=0x2F\0" \ |
| "logic_addr=0x0\0" \ |
| "cec_ac_wakeup=1\0" \ |
| "check_connector_type="\ |
| "setenv bootconfig ${bootconfig} androidboot.connector_type=" \ |
| "${connector_type};\0"\ |
| "check_connector1_type="\ |
| "setenv bootconfig ${bootconfig} androidboot.connector1_type=" \ |
| "${connector1_type};\0"\ |
| "check_connector2_type="\ |
| "setenv bootconfig ${bootconfig} androidboot.connector2_type=" \ |
| "${connector2_type};\0"\ |
| CONFIG_EXTRA_HDMI_ENV_SETTINGS \ |
| "initargs="\ |
| "init=/init" CONFIG_KNL_LOG_LEVEL "console=ttyS0,921600 no_console_suspend "\ |
| "earlycon=aml-uart,0xfe078000 ramoops.pstore_en=1 ramoops.record_size=0x8000 "\ |
| "ramoops.console_size=0x4000 loop.max_part=4 scsi_mod.scan=async "\ |
| "xhci_hcd.quirks=0x800000 loglevel=4 scramble_reg=0xfe02e030 "\ |
| "\0"\ |
| "upgrade_check="\ |
| "run upgrade_check_base;"\ |
| "\0"\ |
| "storeargs="\ |
| "get_bootloaderversion;" \ |
| "run storeargs_base;"\ |
| "setenv bootargs ${bootargs} kvm-arm.mode=none init_on_alloc=0 "\ |
| "nn_adj_vol=${nn_adj_vol};"\ |
| "run storeargs_hdmitx;"\ |
| "run cmdline_keys;"\ |
| "run check_connector_type; " \ |
| "run check_connector1_type; " \ |
| "run check_connector2_type; " \ |
| "\0"\ |
| "cec_init="\ |
| "echo cec_ac_wakeup=${cec_ac_wakeup}; "\ |
| "if test ${cec_ac_wakeup} = 1; then "\ |
| "cec ${logic_addr} ${cec_fun}; "\ |
| "if test ${edid_select} = 1111; then "\ |
| "hdmirx init ${port_map} ${edid_20_dir}; "\ |
| "else "\ |
| "hdmirx init ${port_map} ${edid_14_dir}; "\ |
| "fi;"\ |
| "fi;"\ |
| "\0"\ |
| "ffv_freeze_action="\ |
| "run cec_init;"\ |
| "setenv ffv_freeze on;"\ |
| "setenv bootargs ${bootargs} ffv_freeze=on"\ |
| "\0"\ |
| "cold_boot_normal_check="\ |
| "setenv bootargs ${bootargs} ffv_freeze=off; "\ |
| /*"run try_auto_burn;uboot wake up "*/\ |
| "if test ${powermode} = on; then "\ |
| /*"run try_auto_burn; "*/\ |
| "else if test ${powermode} = standby; then "\ |
| "run cec_init;"\ |
| "systemoff; "\ |
| "else if test ${powermode} = last; then "\ |
| "echo suspend=${suspend}; "\ |
| "if test ${suspend} = off; then "\ |
| /*"run try_auto_burn; "*/\ |
| "else if test ${suspend} = on; then "\ |
| "run cec_init;"\ |
| "systemoff; "\ |
| "else if test ${suspend} = shutdown; then "\ |
| "run cec_init;"\ |
| "systemoff; "\ |
| "fi; fi; fi; "\ |
| "fi; fi; fi; "\ |
| "\0"\ |
| "switch_bootmode="\ |
| "get_rebootmode;"\ |
| "setenv ffv_freeze off;"\ |
| "echo reboot_mode : ${reboot_mode};"\ |
| "if test ${reboot_mode} = factory_reset; then "\ |
| "run recovery_from_flash;"\ |
| "else if test ${reboot_mode} = update; then "\ |
| "run update;"\ |
| "else if test ${reboot_mode} = quiescent; then "\ |
| "setenv bootconfig ${bootconfig} androidboot.quiescent=1;"\ |
| "else if test ${reboot_mode} = recovery_quiescent; then "\ |
| "setenv bootconfig ${bootconfig} androidboot.quiescent=1;"\ |
| "run recovery_from_flash;"\ |
| "else if test ${reboot_mode} = cold_boot; then "\ |
| "echo cold boot: ffv_wake=${ffv_wake} "\ |
| "powermode=${powermode} suspend=${suspend};"\ |
| "if test ${ffv_wake} = on; then "\ |
| "if test ${powermode} = on; then "\ |
| "setenv bootargs ${bootargs} ffv_freeze=off; "\ |
| "else if test ${powermode} = standby; then "\ |
| "run ffv_freeze_action; "\ |
| "else if test ${powermode} = last; then "\ |
| "if test ${suspend} = off; then "\ |
| "setenv bootargs ${bootargs} ffv_freeze=off; "\ |
| "else if test ${suspend} = on; then "\ |
| "run ffv_freeze_action; "\ |
| "else if test ${suspend} = shutdown; then "\ |
| "run ffv_freeze_action; "\ |
| "fi; fi; fi; "\ |
| "fi; fi; fi; "\ |
| "else "\ |
| "run cold_boot_normal_check;"\ |
| "fi; "\ |
| "else if test ${reboot_mode} = ffv_reboot; then "\ |
| "if test ${ffv_wake} = on; then "\ |
| "run ffv_freeze_action; "\ |
| "fi; "\ |
| "else if test ${reboot_mode} = fastboot; then "\ |
| "fastboot 1;"\ |
| "fi;fi;fi;fi;fi;fi;fi;"\ |
| "\0" \ |
| "reset_suspend="\ |
| "if test ${ffv_freeze} != on; then "\ |
| "if test ${suspend} = on || test ${suspend} = shutdown; then "\ |
| "setenv suspend off;"\ |
| "saveenv;"\ |
| "fi;"\ |
| "fi;"\ |
| "\0" \ |
| "storeboot="\ |
| "run storeboot_base;"\ |
| "\0"\ |
| "update="\ |
| "run update_base;"\ |
| "\0"\ |
| "enter_fastboot="\ |
| "fastboot 1;"\ |
| "\0"\ |
| "recovery_from_fat_dev="\ |
| "run recovery_from_fat_dev_base;"\ |
| "\0"\ |
| "recovery_from_udisk="\ |
| "run recovery_from_udisk_base;"\ |
| "\0"\ |
| "recovery_from_sdcard="\ |
| "run recovery_from_sdcard_base;"\ |
| "\0"\ |
| "recovery_from_flash="\ |
| "run recovery_from_flash_base;"\ |
| "\0"\ |
| "bcb_cmd="\ |
| "run bcb_cmd_base;"\ |
| "\0"\ |
| "load_bmp_logo="\ |
| "run load_bmp_logo_base;"\ |
| "\0"\ |
| "init_display="\ |
| "run init_display_hdmitx;"\ |
| "\0"\ |
| "check_display="\ |
| "if test ${reboot_mode} = cold_boot; then "\ |
| "if test ${powermode} = standby; then "\ |
| "echo not init_display; "\ |
| "else if test ${powermode} = last; then "\ |
| "echo suspend=${suspend}; "\ |
| "if test ${suspend} = off; then "\ |
| "run init_display; "\ |
| "else if test ${suspend} = on; then "\ |
| "echo not init_display; "\ |
| "else if test ${suspend} = shutdown; then "\ |
| "echo not init_display; "\ |
| "fi; fi; fi; "\ |
| "else "\ |
| "run init_display; "\ |
| "fi; fi; "\ |
| "else if test ${reboot_mode} = ffv_reboot; then "\ |
| "if test ${ffv_wake} = on; then "\ |
| "echo ffv reboot no display; "\ |
| "else "\ |
| "run init_display; "\ |
| "fi; "\ |
| "else "\ |
| "run init_display; "\ |
| "fi;fi; "\ |
| "\0"\ |
| "cmdline_keys="\ |
| "setenv usid an400${cpu_id};"\ |
| "run cmdline_keys_base;"\ |
| "\0"\ |
| "upgrade_key="\ |
| "if gpio input GPIOD_3; then "\ |
| "echo detect upgrade key;"\ |
| "if test ${boot_flag} = 0; then "\ |
| "echo enter fastboot; setenv boot_flag 1; saveenv; fastboot 1;"\ |
| "else if test ${boot_flag} = 1; then "\ |
| "echo enter update; setenv boot_flag 2; saveenv; run update;"\ |
| "else "\ |
| "echo enter recovery; setenv boot_flag 0; saveenv; "\ |
| "run recovery_from_flash;"\ |
| "fi;fi;"\ |
| "fi;"\ |
| "\0" |
| |
| |
| #define CONFIG_PREBOOT \ |
| "run upgrade_check;"\ |
| "run check_display;"\ |
| "run storeargs;"\ |
| "run upgrade_key;" \ |
| "bcb uboot-command;" \ |
| "run switch_bootmode;" \ |
| "run reset_suspend;" |
| |
| #ifndef CONFIG_HDMITX_ONLY |
| /* dual logo, normal boot */ |
| #define CONFIG_DUAL_LOGO \ |
| "setenv outputmode2 ${hdmimode};"\ |
| "setenv display_layer viu2_osd0;vout2 prepare ${outputmode2};"\ |
| "osd open;osd clear;run load_bmp_logo;vout2 output ${outputmode2};bmp scale;"\ |
| "if test ${outputmode2} = ${hmdimode}; then "\ |
| "dovi set;dovi pkg;vpp hdrpkt;"\ |
| "fi; "\ |
| "setenv display_layer osd0;osd open;osd clear;"\ |
| "run load_bmp_logo;bmp scale;vout output ${outputmode};"\ |
| "if test ${outputmode} = ${hmdimode}; then "\ |
| "dovi set;dovi pkg;vpp hdrpkt;"\ |
| "fi; "\ |
| "\0"\ |
| |
| /* dual logo, factory_reset boot, recovery always displays on panel */ |
| #define CONFIG_RECOVERY_DUAL_LOGO \ |
| "setenv outputmode2 ${hdmimode};"\ |
| "setenv display_layer viu2_osd0;vout2 prepare ${outputmode2};"\ |
| "osd open;osd clear;run load_bmp_logo;vout2 output ${outputmode2};bmp scale;"\ |
| "if test ${outputmode2} = ${hmdimode}; then "\ |
| "dovi set;dovi pkg;vpp hdrpkt;"\ |
| "fi; "\ |
| "setenv display_layer osd0;osd open;osd clear;"\ |
| "run load_bmp_logo;bmp scale;vout output ${outputmode};"\ |
| "if test ${outputmode} = ${hmdimode}; then "\ |
| "dovi set;dovi pkg;vpp hdrpkt;"\ |
| "fi; "\ |
| "\0"\ |
| |
| /* single logo */ |
| #define CONFIG_SINGLE_LOGO \ |
| "setenv display_layer osd0;osd open;osd clear;"\ |
| "run load_bmp_logo;bmp scale;vout output ${outputmode};"\ |
| "if test ${outputmode} = ${hmdimode}; then "\ |
| "dovi set;dovi pkg;vpp hdrpkt;"\ |
| "fi; "\ |
| "\0" |
| #endif |
| |
| /* #define CONFIG_ENV_IS_NOWHERE 1 */ |
| #define CONFIG_ENV_SIZE (64*1024) |
| #define CONFIG_FIT 1 |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_ANDROID_BOOT_IMAGE 1 |
| #define CONFIG_SYS_BOOTM_LEN (64<<20) /* Increase max gunzip size*/ |
| |
| /* ATTENTION */ |
| /* DDR configs move to board/amlogic/[board]/firmware/timing.c */ |
| |
| /* running in sram */ |
| //#define UBOOT_RUN_IN_SRAM |
| #ifdef UBOOT_RUN_IN_SRAM |
| #define CONFIG_SYS_INIT_SP_ADDR (0x00300000) |
| /* Size of malloc() pool */ |
| #define CONFIG_SYS_MALLOC_LEN (256*1024) |
| #else |
| #define CONFIG_SYS_INIT_SP_ADDR (0x00300000) |
| #define CONFIG_SYS_MALLOC_LEN (96*1024*1024) |
| #endif |
| |
| //#define CONFIG_NR_DRAM_BANKS 1 |
| /* ddr functions */ |
| #define DDR_FULL_TEST 0 //0:disable, 1:enable. ddr full test |
| #define DDR_LOW_POWER 0 //0:disable, 1:enable. ddr clk gate for lp |
| #define DDR_ZQ_PD 0 //0:disable, 1:enable. ddr zq power down |
| #define DDR_USE_EXT_VREF 0 //0:disable, 1:enable. ddr use external vref |
| #define DDR4_TIMING_TEST 0 //0:disable, 1:enable. ddr4 timing test function |
| #define DDR_PLL_BYPASS 0 //0:disable, 1:enable. ddr pll bypass function |
| |
| /* storage: emmc/nand/sd */ |
| #define CONFIG_ENV_OVERWRITE |
| /* #define CONFIG_CMD_SAVEENV */ |
| /* fixme, need fix*/ |
| |
| #if (defined(CONFIG_ENV_IS_IN_AMLNAND) || defined(CONFIG_ENV_IS_IN_MMC)) && defined(CONFIG_STORE_COMPATIBLE) |
| #error env in amlnand/mmc already be compatible; |
| #endif |
| |
| /* |
| * storage |
| * |---------|---------| |
| * | | |
| * emmc<--Compatible-->nand |
| * |-------|-------| |
| * | | |
| * MTD<-Exclusive->NFTL |
| * | |
| * |***************|***************| |
| * slc-nand SPI-nand SPI-nor |
| * (raw nand) |
| */ |
| /* axg only support slc nand */ |
| /* swither for mtd nand which is for slc only. */ |
| |
| |
| #if defined(CONFIG_AML_NAND) && defined(CONFIG_MESON_NFC) |
| #error CONFIG_AML_NAND/CONFIG_MESON_NFC can not support at the sametime; |
| #endif |
| |
| #if (defined(CONFIG_AML_NAND) || defined(CONFIG_MESON_NFC)) && defined(CONFIG_MESON_FBOOT) |
| #error CONFIG_AML_NAND/CONFIG_MESON_NFC CONFIG _MESON_FBOOT can not support at the sametime; |
| #endif |
| |
| #if defined(CONFIG_SPI_NAND) && defined(CONFIG_MTD_SPI_NAND) && defined(CONFIG_MESON_NFC) |
| #error CONFIG_SPI_NAND/CONFIG_MTD_SPI_NAND/CONFIG_MESON_NFC can not support at the sametime; |
| #endif |
| |
| /* #define CONFIG_AML_SD_EMMC 1 */ |
| #ifdef CONFIG_AML_SD_EMMC |
| #define CONFIG_GENERIC_MMC 1 |
| #define CONFIG_CMD_MMC 1 |
| #define CONFIG_CMD_GPT 1 |
| #define CONFIG_SYS_MMC_ENV_DEV 1 |
| #define CONFIG_EMMC_DDR52_EN 0 |
| #define CONFIG_EMMC_DDR52_CLK 35000000 |
| #endif |
| #define CONFIG_PARTITIONS 1 |
| #if 0 |
| #define CONFIG_SYS_NO_FLASH 1 |
| #endif |
| |
| #if defined CONFIG_MESON_NFC || defined CONFIG_SPI_NAND || defined CONFIG_MTD_SPI_NAND |
| #define CONFIG_SYS_MAX_NAND_DEVICE 2 |
| #endif |
| |
| /* vpu */ |
| #define AML_VPU_CLK_LEVEL_DFT 7 |
| /* LCD */ |
| |
| /* osd */ |
| #define OSD_SCALE_ENABLE |
| #define AML_OSD_HIGH_VERSION |
| #define AML_T7_DISPLAY |
| #define VEHICLE_CONFIG |
| |
| /* USB |
| * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard |
| * Enable CONFIG_MUSB_UDD for Device functionalities. |
| */ |
| /* #define CONFIG_MUSB_UDC 1 */ |
| /* #define CONFIG_CMD_USB 1 */ |
| |
| #define USB_PHY2_PLL_PARAMETER_1 0x09400414 |
| #define USB_PHY2_PLL_PARAMETER_2 0x927e0000 |
| #define USB_PHY2_PLL_PARAMETER_3 0xAC5F49E5 |
| |
| #define USB_G12x_PHY_PLL_SETTING_1 (0xfe18) |
| #define USB_G12x_PHY_PLL_SETTING_2 (0xfff) |
| #define USB_G12x_PHY_PLL_SETTING_3 (0x78000) |
| #define USB_G12x_PHY_PLL_SETTING_4 (0xe0004) |
| #define USB_G12x_PHY_PLL_SETTING_5 (0xe000c) |
| |
| #define AML_TXLX_USB 1 |
| #define AML_USB_V2 1 |
| #define USB_GENERAL_BIT 3 |
| #define USB_PHY21_BIT 4 |
| |
| /* UBOOT fastboot config */ |
| |
| |
| /* UBOOT factory usb/sdcard burning config */ |
| |
| /* net */ |
| #define CONFIG_CMD_NET 1 |
| #define CONFIG_ETH_DESIGNWARE |
| #if defined(CONFIG_CMD_NET) |
| #define CONFIG_DESIGNWARE_ETH 1 |
| #define CONFIG_PHYLIB 1 |
| #define CONFIG_NET_MULTI 1 |
| #define CONFIG_CMD_PING 1 |
| #define CONFIG_CMD_DHCP 1 |
| #define CONFIG_CMD_RARP 1 |
| #define CONFIG_HOSTNAME "arm_gxbb" |
| #if 0 |
| #define CONFIG_RANDOM_ETHADDR 1 /* use random eth addr, or default */ |
| #endif |
| #define CONFIG_ETHADDR 00:15:18:01:81:31 /* Ethernet address */ |
| #define CONFIG_IPADDR 10.18.9.97 /* Our ip address */ |
| #define CONFIG_GATEWAYIP 10.18.9.1 /* Our getway ip address */ |
| #define CONFIG_SERVERIP 10.18.9.113 /* Tftp server ip address */ |
| #define CONFIG_NETMASK 255.255.255.0 |
| #endif /* (CONFIG_CMD_NET) */ |
| |
| #define MAC_ADDR_NEW 1 |
| |
| /* other devices */ |
| #define CONFIG_SHA1 1 |
| #define CONFIG_MD5 1 |
| |
| /* commands */ |
| #define CONFIG_CMD_PLLTEST 1 |
| |
| /*file system*/ |
| #define CONFIG_DOS_PARTITION 1 |
| #define CONFIG_EFI_PARTITION 1 |
| /* #define CONFIG_MMC 1 */ |
| #define CONFIG_FS_FAT 1 |
| #define CONFIG_FS_EXT4 1 |
| #define CONFIG_LZO 1 |
| |
| #define CONFIG_FAT_WRITE 1 |
| #define CONFIG_AML_FACTORY_PROVISION 1 |
| |
| /* Cache Definitions */ |
| /* #define CONFIG_SYS_DCACHE_OFF */ |
| /* #define CONFIG_SYS_ICACHE_OFF */ |
| |
| /* other functions */ |
| #define CONFIG_LIBAVB 1 |
| |
| /* define CONFIG_SYS_MEM_TOP_HIDE 8M space for free buffer */ |
| #define CONFIG_SYS_MEM_TOP_HIDE 0x00800000 |
| |
| #define CONFIG_CPU_ARMV8 |
| |
| //use sha2 command |
| #define CONFIG_CMD_SHA2 |
| |
| //use startdsp command |
| #define CONFIG_CMD_STARTDSP |
| |
| //use cache command |
| #define CONFIG_CMD_CACHE |
| |
| //use remapset command |
| #define CONFIG_CMD_REMAPSET |
| |
| //use hardware sha2 |
| //#define CONFIG_AML_HW_SHA2 |
| |
| //Replace avb2 software SHA256 to utilize armce |
| #define CONFIG_AVB2_UBOOT_SHA256 |
| |
| #define CONFIG_MULTI_DTB 1 |
| // use auto select DTB table |
| #ifdef CONFIG_MULTI_DTB |
| #define CONFIG_T7_3G_SIZE 0xC0000000 |
| #define CONFIG_T7_4G_SIZE 0x100000000 |
| #define CONFIG_T7_6G_SIZE 0x180000000 |
| #define CONFIG_T7_8G_SIZE 0x200000000 |
| #endif |
| |
| #define CONFIG_RX_RTERM 1 |
| #define CONFIG_CMD_HDMIRX 1 |
| #define CONFIG_CMD_CEC 1 |
| /* define CONFIG_UPDATE_MMU_TABLE for need update mmu */ |
| #define CONFIG_UPDATE_MMU_TABLE |
| |
| /* support secure boot */ |
| #define CONFIG_AML_SECURE_UBOOT 1 |
| |
| #if defined(CONFIG_AML_SECURE_UBOOT) |
| |
| /* unify build for generate encrypted bootloader "u-boot.bin.encrypt" */ |
| #define CONFIG_AML_CRYPTO_UBOOT 1 |
| //#define CONFIG_AML_SIGNED_UBOOT 1 |
| /* unify build for generate encrypted kernel image |
| SRC : "board/amlogic/(board)/boot.img" |
| DST : "fip/boot.img.encrypt" */ |
| /* #define CONFIG_AML_CRYPTO_IMG 1 */ |
| |
| #endif /* CONFIG_AML_SECURE_UBOOT */ |
| |
| #define CONFIG_FIP_IMG_SUPPORT 1 |
| |
| /* config ramdump to debug kernel panic */ |
| #define CONFIG_FULL_RAMDUMP |
| |
| #define BL32_SHARE_MEM_SIZE 0x800000 |
| #define CONFIG_AML_KASLR_SEED |
| |
| #endif |
