blob: 7265d7072b5cb7156ecca1945eab44a34a637211 [file] [log] [blame]
/*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <dt-bindings/input/input.h>
/ {
chosen {
stdout-path = &uart1;
};
cpus {
cpu@0 {
cpu0-supply = <&vcc>;
};
};
memory@80000000 {
device_type = "memory";
reg = <0x80000000 0>;
};
leds {
compatible = "gpio-leds";
user0 {
label = "user0";
gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* LEDA */
linux,default-trigger = "none";
};
};
wl12xx_vmmc: wl12xx_vmmc {
compatible = "regulator-fixed";
regulator-name = "vwl1271";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&gpio5 29 0>; /* gpio157 */
startup-delay-us = <70000>;
enable-active-high;
vin-supply = <&vmmc2>;
};
};
&gpmc {
ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
nand@0,0 {
compatible = "ti,omap2-nand";
reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
interrupt-parent = <&gpmc>;
interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
<1 IRQ_TYPE_NONE>; /* termcount */
linux,mtd-name = "micron,mt29f4g16abbda3w";
nand-bus-width = <16>;
ti,nand-ecc-opt = "bch8";
rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
gpmc,sync-clk-ps = <0>;
gpmc,cs-on-ns = <0>;
gpmc,cs-rd-off-ns = <44>;
gpmc,cs-wr-off-ns = <44>;
gpmc,adv-on-ns = <6>;
gpmc,adv-rd-off-ns = <34>;
gpmc,adv-wr-off-ns = <44>;
gpmc,we-off-ns = <40>;
gpmc,oe-off-ns = <54>;
gpmc,access-ns = <64>;
gpmc,rd-cycle-ns = <82>;
gpmc,wr-cycle-ns = <82>;
gpmc,wr-access-ns = <40>;
gpmc,wr-data-mux-bus-ns = <0>;
gpmc,device-width = <2>;
#address-cells = <1>;
#size-cells = <1>;
/* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */
x-loader@0 {
label = "x-loader";
reg = <0 0x80000>;
};
bootloaders@80000 {
label = "u-boot";
reg = <0x80000 0x1e0000>;
};
bootloaders_env@260000 {
label = "u-boot-env";
reg = <0x260000 0x20000>;
};
kernel@280000 {
label = "kernel";
reg = <0x280000 0x400000>;
};
filesystem@680000 {
label = "fs";
reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */
};
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <2600000>;
twl: twl@48 {
reg = <0x48>;
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
interrupt-parent = <&intc>;
twl_audio: audio {
compatible = "ti,twl4030-audio";
codec {
};
};
};
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
clock-frequency = <400000>;
};
&i2c3 {
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins>;
clock-frequency = <400000>;
at24@50 {
compatible = "atmel,24c64";
readonly;
reg = <0x50>;
};
};
/*
* Only found on the wireless SOM. For the SOM without wireless, the pins for
* MMC3 can be routed with jumpers to the second MMC slot on the devkit and
* gpio157 is not connected. So this should be OK to keep common for now,
* probably device tree overlays is the way to go with the various SOM and
* jumpering combinations for the long run.
*/
&mmc3 {
interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
pinctrl-names = "default";
vmmc-supply = <&wl12xx_vmmc>;
non-removable;
bus-width = <4>;
cap-power-off-card;
#address-cells = <1>;
#size-cells = <0>;
wlcore: wlcore@2 {
compatible = "ti,wl1283";
reg = <2>;
interrupt-parent = <&gpio5>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
ref-clock-frequency = <26000000>;
tcxo-clock-frequency = <26000000>;
};
};
&omap3_pmx_core {
mmc3_pins: pinmux_mm3_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */
>;
};
mcbsp2_pins: pinmux_mcbsp2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */
OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */
OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */
>;
};
uart2_pins: pinmux_uart2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */
OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/
OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
>;
};
mcspi1_pins: pinmux_mcspi1_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
>;
};
hsusb_otg_pins: pinmux_hsusb_otg_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
>;
};
i2c1_pins: pinmux_i2c1_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */
OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */
>;
};
i2c2_pins: pinmux_i2c2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
>;
};
i2c3_pins: pinmux_i2c3_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */
OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */
>;
};
};
&uart2 {
interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
};
&mcspi1 {
pinctrl-names = "default";
pinctrl-0 = <&mcspi1_pins>;
};
&omap3_pmx_core2 {
mmc3_core2_pins: pinmux_mmc3_core2_pins {
pinctrl-single,pins = <
OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */
OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */
>;
};
};
#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"
&twl {
twl_power: power {
compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
ti,use_poweroff;
};
};
&twl_gpio {
ti,use-leds;
};
&twl_keypad {
status = "disabled";
};