blob: 6a8c5f71787add631e3eda29529104ceca778bfb [file] [log] [blame]
/*
* Copyright (c) 2005-2011 Atheros Communications Inc.
* Copyright (c) 2011-2013 Qualcomm Atheros, Inc.
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
#ifndef _HW_H_
#define _HW_H_
#include "targaddrs.h"
#define ATH10K_FW_DIR "ath10k"
#define QCA988X_2_0_DEVICE_ID (0x003c)
#define QCA6164_2_1_DEVICE_ID (0x0041)
#define QCA6174_2_1_DEVICE_ID (0x003e)
#define QCA99X0_2_0_DEVICE_ID (0x0040)
#define QCA9888_2_0_DEVICE_ID (0x0056)
#define QCA9984_1_0_DEVICE_ID (0x0046)
#define QCA9377_1_0_DEVICE_ID (0x0042)
#define QCA9887_1_0_DEVICE_ID (0x0050)
/* QCA988X 1.0 definitions (unsupported) */
#define QCA988X_HW_1_0_CHIP_ID_REV 0x0
/* QCA988X 2.0 definitions */
#define QCA988X_HW_2_0_VERSION 0x4100016c
#define QCA988X_HW_2_0_CHIP_ID_REV 0x2
#define QCA988X_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA988X/hw2.0"
#define QCA988X_HW_2_0_BOARD_DATA_FILE "board.bin"
#define QCA988X_HW_2_0_PATCH_LOAD_ADDR 0x1234
/* QCA9887 1.0 definitions */
#define QCA9887_HW_1_0_VERSION 0x4100016d
#define QCA9887_HW_1_0_CHIP_ID_REV 0
#define QCA9887_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9887/hw1.0"
#define QCA9887_HW_1_0_BOARD_DATA_FILE "board.bin"
#define QCA9887_HW_1_0_PATCH_LOAD_ADDR 0x1234
/* QCA6174 target BMI version signatures */
#define QCA6174_HW_1_0_VERSION 0x05000000
#define QCA6174_HW_1_1_VERSION 0x05000001
#define QCA6174_HW_1_3_VERSION 0x05000003
#define QCA6174_HW_2_1_VERSION 0x05010000
#define QCA6174_HW_3_0_VERSION 0x05020000
#define QCA6174_HW_3_2_VERSION 0x05030000
/* QCA9377 target BMI version signatures */
#define QCA9377_HW_1_0_DEV_VERSION 0x05020000
#define QCA9377_HW_1_1_DEV_VERSION 0x05020001
enum qca6174_pci_rev {
QCA6174_PCI_REV_1_1 = 0x11,
QCA6174_PCI_REV_1_3 = 0x13,
QCA6174_PCI_REV_2_0 = 0x20,
QCA6174_PCI_REV_3_0 = 0x30,
};
enum qca6174_chip_id_rev {
QCA6174_HW_1_0_CHIP_ID_REV = 0,
QCA6174_HW_1_1_CHIP_ID_REV = 1,
QCA6174_HW_1_3_CHIP_ID_REV = 2,
QCA6174_HW_2_1_CHIP_ID_REV = 4,
QCA6174_HW_2_2_CHIP_ID_REV = 5,
QCA6174_HW_3_0_CHIP_ID_REV = 8,
QCA6174_HW_3_1_CHIP_ID_REV = 9,
QCA6174_HW_3_2_CHIP_ID_REV = 10,
};
enum qca9377_chip_id_rev {
QCA9377_HW_1_0_CHIP_ID_REV = 0x0,
QCA9377_HW_1_1_CHIP_ID_REV = 0x1,
};
#define QCA6174_HW_2_1_FW_DIR "ath10k/QCA6174/hw2.1"
#define QCA6174_HW_2_1_BOARD_DATA_FILE "board.bin"
#define QCA6174_HW_2_1_PATCH_LOAD_ADDR 0x1234
#define QCA6174_HW_3_0_FW_DIR "ath10k/QCA6174/hw3.0"
#define QCA6174_HW_3_0_BOARD_DATA_FILE "board.bin"
#define QCA6174_HW_3_0_PATCH_LOAD_ADDR 0x1234
/* QCA99X0 1.0 definitions (unsupported) */
#define QCA99X0_HW_1_0_CHIP_ID_REV 0x0
/* QCA99X0 2.0 definitions */
#define QCA99X0_HW_2_0_DEV_VERSION 0x01000000
#define QCA99X0_HW_2_0_CHIP_ID_REV 0x1
#define QCA99X0_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA99X0/hw2.0"
#define QCA99X0_HW_2_0_BOARD_DATA_FILE "board.bin"
#define QCA99X0_HW_2_0_PATCH_LOAD_ADDR 0x1234
/* QCA9984 1.0 defines */
#define QCA9984_HW_1_0_DEV_VERSION 0x1000000
#define QCA9984_HW_DEV_TYPE 0xa
#define QCA9984_HW_1_0_CHIP_ID_REV 0x0
#define QCA9984_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9984/hw1.0"
#define QCA9984_HW_1_0_BOARD_DATA_FILE "board.bin"
#define QCA9984_HW_1_0_PATCH_LOAD_ADDR 0x1234
/* QCA9888 2.0 defines */
#define QCA9888_HW_2_0_DEV_VERSION 0x1000000
#define QCA9888_HW_DEV_TYPE 0xc
#define QCA9888_HW_2_0_CHIP_ID_REV 0x0
#define QCA9888_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA9888/hw2.0"
#define QCA9888_HW_2_0_BOARD_DATA_FILE "board.bin"
#define QCA9888_HW_2_0_PATCH_LOAD_ADDR 0x1234
/* QCA9377 1.0 definitions */
#define QCA9377_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9377/hw1.0"
#define QCA9377_HW_1_0_BOARD_DATA_FILE "board.bin"
#define QCA9377_HW_1_0_PATCH_LOAD_ADDR 0x1234
/* QCA4019 1.0 definitions */
#define QCA4019_HW_1_0_DEV_VERSION 0x01000000
#define QCA4019_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA4019/hw1.0"
#define QCA4019_HW_1_0_BOARD_DATA_FILE "board.bin"
#define QCA4019_HW_1_0_PATCH_LOAD_ADDR 0x1234
#define ATH10K_FW_FILE_BASE "firmware"
#define ATH10K_FW_API_MAX 6
#define ATH10K_FW_API_MIN 2
#define ATH10K_FW_API2_FILE "firmware-2.bin"
#define ATH10K_FW_API3_FILE "firmware-3.bin"
/* added support for ATH10K_FW_IE_WMI_OP_VERSION */
#define ATH10K_FW_API4_FILE "firmware-4.bin"
/* HTT id conflict fix for management frames over HTT */
#define ATH10K_FW_API5_FILE "firmware-5.bin"
/* the firmware-6.bin blob */
#define ATH10K_FW_API6_FILE "firmware-6.bin"
#define ATH10K_FW_UTF_FILE "utf.bin"
#define ATH10K_FW_UTF_API2_FILE "utf-2.bin"
/* includes also the null byte */
#define ATH10K_FIRMWARE_MAGIC "QCA-ATH10K"
#define ATH10K_BOARD_MAGIC "QCA-ATH10K-BOARD"
#define ATH10K_BOARD_API2_FILE "board-2.bin"
#define REG_DUMP_COUNT_QCA988X 60
struct ath10k_fw_ie {
__le32 id;
__le32 len;
u8 data[0];
};
enum ath10k_fw_ie_type {
ATH10K_FW_IE_FW_VERSION = 0,
ATH10K_FW_IE_TIMESTAMP = 1,
ATH10K_FW_IE_FEATURES = 2,
ATH10K_FW_IE_FW_IMAGE = 3,
ATH10K_FW_IE_OTP_IMAGE = 4,
/* WMI "operations" interface version, 32 bit value. Supported from
* FW API 4 and above.
*/
ATH10K_FW_IE_WMI_OP_VERSION = 5,
/* HTT "operations" interface version, 32 bit value. Supported from
* FW API 5 and above.
*/
ATH10K_FW_IE_HTT_OP_VERSION = 6,
/* Code swap image for firmware binary */
ATH10K_FW_IE_FW_CODE_SWAP_IMAGE = 7,
};
enum ath10k_fw_wmi_op_version {
ATH10K_FW_WMI_OP_VERSION_UNSET = 0,
ATH10K_FW_WMI_OP_VERSION_MAIN = 1,
ATH10K_FW_WMI_OP_VERSION_10_1 = 2,
ATH10K_FW_WMI_OP_VERSION_10_2 = 3,
ATH10K_FW_WMI_OP_VERSION_TLV = 4,
ATH10K_FW_WMI_OP_VERSION_10_2_4 = 5,
ATH10K_FW_WMI_OP_VERSION_10_4 = 6,
/* keep last */
ATH10K_FW_WMI_OP_VERSION_MAX,
};
enum ath10k_fw_htt_op_version {
ATH10K_FW_HTT_OP_VERSION_UNSET = 0,
ATH10K_FW_HTT_OP_VERSION_MAIN = 1,
/* also used in 10.2 and 10.2.4 branches */
ATH10K_FW_HTT_OP_VERSION_10_1 = 2,
ATH10K_FW_HTT_OP_VERSION_TLV = 3,
ATH10K_FW_HTT_OP_VERSION_10_4 = 4,
/* keep last */
ATH10K_FW_HTT_OP_VERSION_MAX,
};
enum ath10k_bd_ie_type {
/* contains sub IEs of enum ath10k_bd_ie_board_type */
ATH10K_BD_IE_BOARD = 0,
};
enum ath10k_bd_ie_board_type {
ATH10K_BD_IE_BOARD_NAME = 0,
ATH10K_BD_IE_BOARD_DATA = 1,
};
enum ath10k_hw_rev {
ATH10K_HW_QCA988X,
ATH10K_HW_QCA6174,
ATH10K_HW_QCA99X0,
ATH10K_HW_QCA9888,
ATH10K_HW_QCA9984,
ATH10K_HW_QCA9377,
ATH10K_HW_QCA4019,
ATH10K_HW_QCA9887,
ATH10K_HW_WCN3990,
};
struct ath10k_hw_regs {
u32 rtc_soc_base_address;
u32 rtc_wmac_base_address;
u32 soc_core_base_address;
u32 wlan_mac_base_address;
u32 ce_wrapper_base_address;
u32 ce0_base_address;
u32 ce1_base_address;
u32 ce2_base_address;
u32 ce3_base_address;
u32 ce4_base_address;
u32 ce5_base_address;
u32 ce6_base_address;
u32 ce7_base_address;
u32 ce8_base_address;
u32 ce9_base_address;
u32 ce10_base_address;
u32 ce11_base_address;
u32 soc_reset_control_si0_rst_mask;
u32 soc_reset_control_ce_rst_mask;
u32 soc_chip_id_address;
u32 scratch_3_address;
u32 fw_indicator_address;
u32 pcie_local_base_address;
u32 ce_wrap_intr_sum_host_msi_lsb;
u32 ce_wrap_intr_sum_host_msi_mask;
u32 pcie_intr_fw_mask;
u32 pcie_intr_ce_mask_all;
u32 pcie_intr_clr_address;
u32 cpu_pll_init_address;
u32 cpu_speed_address;
u32 core_clk_div_address;
};
extern const struct ath10k_hw_regs qca988x_regs;
extern const struct ath10k_hw_regs qca6174_regs;
extern const struct ath10k_hw_regs qca99x0_regs;
extern const struct ath10k_hw_regs qca4019_regs;
extern const struct ath10k_hw_regs wcn3990_regs;
struct ath10k_hw_ce_regs_addr_map {
u32 msb;
u32 lsb;
u32 mask;
};
struct ath10k_hw_ce_ctrl1 {
u32 addr;
u32 hw_mask;
u32 sw_mask;
u32 hw_wr_mask;
u32 sw_wr_mask;
u32 reset_mask;
u32 reset;
struct ath10k_hw_ce_regs_addr_map *src_ring;
struct ath10k_hw_ce_regs_addr_map *dst_ring;
struct ath10k_hw_ce_regs_addr_map *dmax; };
struct ath10k_hw_ce_cmd_halt {
u32 status_reset;
u32 msb;
u32 mask;
struct ath10k_hw_ce_regs_addr_map *status; };
struct ath10k_hw_ce_host_ie {
u32 copy_complete_reset;
struct ath10k_hw_ce_regs_addr_map *copy_complete; };
struct ath10k_hw_ce_host_wm_regs {
u32 dstr_lmask;
u32 dstr_hmask;
u32 srcr_lmask;
u32 srcr_hmask;
u32 cc_mask;
u32 wm_mask;
u32 addr;
};
struct ath10k_hw_ce_misc_regs {
u32 axi_err;
u32 dstr_add_err;
u32 srcr_len_err;
u32 dstr_mlen_vio;
u32 dstr_overflow;
u32 srcr_overflow;
u32 err_mask;
u32 addr;
};
struct ath10k_hw_ce_dst_src_wm_regs {
u32 addr;
u32 low_rst;
u32 high_rst;
struct ath10k_hw_ce_regs_addr_map *wm_low;
struct ath10k_hw_ce_regs_addr_map *wm_high; };
struct ath10k_hw_ce_regs {
u32 sr_base_addr;
u32 sr_size_addr;
u32 dr_base_addr;
u32 dr_size_addr;
u32 ce_cmd_addr;
u32 misc_ie_addr;
u32 sr_wr_index_addr;
u32 dst_wr_index_addr;
u32 current_srri_addr;
u32 current_drri_addr;
u32 ddr_addr_for_rri_low;
u32 ddr_addr_for_rri_high;
u32 ce_rri_low;
u32 ce_rri_high;
u32 host_ie_addr;
struct ath10k_hw_ce_host_wm_regs *wm_regs;
struct ath10k_hw_ce_misc_regs *misc_regs;
struct ath10k_hw_ce_ctrl1 *ctrl1_regs;
struct ath10k_hw_ce_cmd_halt *cmd_halt;
struct ath10k_hw_ce_host_ie *host_ie;
struct ath10k_hw_ce_dst_src_wm_regs *wm_srcr;
struct ath10k_hw_ce_dst_src_wm_regs *wm_dstr; };
struct ath10k_hw_values {
u32 rtc_state_val_on;
u8 ce_count;
u8 msi_assign_ce_max;
u8 num_target_ce_config_wlan;
u16 ce_desc_meta_data_mask;
u8 ce_desc_meta_data_lsb;
};
extern const struct ath10k_hw_values qca988x_values;
extern const struct ath10k_hw_values qca6174_values;
extern const struct ath10k_hw_values qca99x0_values;
extern const struct ath10k_hw_values qca9888_values;
extern const struct ath10k_hw_values qca4019_values;
extern const struct ath10k_hw_values wcn3990_values;
extern struct ath10k_hw_ce_regs wcn3990_ce_regs;
extern struct ath10k_hw_ce_regs qcax_ce_regs;
void ath10k_hw_fill_survey_time(struct ath10k *ar, struct survey_info *survey,
u32 cc, u32 rcc, u32 cc_prev, u32 rcc_prev);
#define QCA_REV_988X(ar) ((ar)->hw_rev == ATH10K_HW_QCA988X)
#define QCA_REV_9887(ar) ((ar)->hw_rev == ATH10K_HW_QCA9887)
#define QCA_REV_6174(ar) ((ar)->hw_rev == ATH10K_HW_QCA6174)
#define QCA_REV_99X0(ar) ((ar)->hw_rev == ATH10K_HW_QCA99X0)
#define QCA_REV_9888(ar) ((ar)->hw_rev == ATH10K_HW_QCA9888)
#define QCA_REV_9984(ar) ((ar)->hw_rev == ATH10K_HW_QCA9984)
#define QCA_REV_9377(ar) ((ar)->hw_rev == ATH10K_HW_QCA9377)
#define QCA_REV_40XX(ar) ((ar)->hw_rev == ATH10K_HW_QCA4019)
#define QCA_REV_WCN3990(ar) ((ar)->hw_rev == ATH10K_HW_WCN3990)
/* Known peculiarities:
* - raw appears in nwifi decap, raw and nwifi appear in ethernet decap
* - raw have FCS, nwifi doesn't
* - ethernet frames have 802.11 header decapped and parts (base hdr, cipher
* param, llc/snap) are aligned to 4byte boundaries each
*/
enum ath10k_hw_txrx_mode {
ATH10K_HW_TXRX_RAW = 0,
/* Native Wifi decap mode is used to align IP frames to 4-byte
* boundaries and avoid a very expensive re-alignment in mac80211.
*/
ATH10K_HW_TXRX_NATIVE_WIFI = 1,
ATH10K_HW_TXRX_ETHERNET = 2,
/* Valid for HTT >= 3.0. Used for management frames in TX_FRM. */
ATH10K_HW_TXRX_MGMT = 3,
};
enum ath10k_mcast2ucast_mode {
ATH10K_MCAST2UCAST_DISABLED = 0,
ATH10K_MCAST2UCAST_ENABLED = 1,
};
enum ath10k_hw_rate_ofdm {
ATH10K_HW_RATE_OFDM_48M = 0,
ATH10K_HW_RATE_OFDM_24M,
ATH10K_HW_RATE_OFDM_12M,
ATH10K_HW_RATE_OFDM_6M,
ATH10K_HW_RATE_OFDM_54M,
ATH10K_HW_RATE_OFDM_36M,
ATH10K_HW_RATE_OFDM_18M,
ATH10K_HW_RATE_OFDM_9M,
};
enum ath10k_hw_rate_cck {
ATH10K_HW_RATE_CCK_LP_11M = 0,
ATH10K_HW_RATE_CCK_LP_5_5M,
ATH10K_HW_RATE_CCK_LP_2M,
ATH10K_HW_RATE_CCK_LP_1M,
ATH10K_HW_RATE_CCK_SP_11M,
ATH10K_HW_RATE_CCK_SP_5_5M,
ATH10K_HW_RATE_CCK_SP_2M,
};
enum ath10k_hw_rate_rev2_cck {
ATH10K_HW_RATE_REV2_CCK_LP_1M = 1,
ATH10K_HW_RATE_REV2_CCK_LP_2M,
ATH10K_HW_RATE_REV2_CCK_LP_5_5M,
ATH10K_HW_RATE_REV2_CCK_LP_11M,
ATH10K_HW_RATE_REV2_CCK_SP_2M,
ATH10K_HW_RATE_REV2_CCK_SP_5_5M,
ATH10K_HW_RATE_REV2_CCK_SP_11M,
};
enum ath10k_hw_cc_wraparound_type {
ATH10K_HW_CC_WRAP_DISABLED = 0,
/* This type is when the HW chip has a quirky Cycle Counter
* wraparound which resets to 0x7fffffff instead of 0. All
* other CC related counters (e.g. Rx Clear Count) are divided
* by 2 so they never wraparound themselves.
*/
ATH10K_HW_CC_WRAP_SHIFTED_ALL = 1,
/* Each hw counter wrapsaround independently. When the
* counter overflows the repestive counter is right shifted
* by 1, i.e reset to 0x7fffffff, and other counters will be
* running unaffected. In this type of wraparound, it should
* be possible to report accurate Rx busy time unlike the
* first type.
*/
ATH10K_HW_CC_WRAP_SHIFTED_EACH = 2,
};
enum ath10k_hw_refclk_speed {
ATH10K_HW_REFCLK_UNKNOWN = -1,
ATH10K_HW_REFCLK_48_MHZ = 0,
ATH10K_HW_REFCLK_19_2_MHZ = 1,
ATH10K_HW_REFCLK_24_MHZ = 2,
ATH10K_HW_REFCLK_26_MHZ = 3,
ATH10K_HW_REFCLK_37_4_MHZ = 4,
ATH10K_HW_REFCLK_38_4_MHZ = 5,
ATH10K_HW_REFCLK_40_MHZ = 6,
ATH10K_HW_REFCLK_52_MHZ = 7,
/* must be the last one */
ATH10K_HW_REFCLK_COUNT,
};
struct ath10k_hw_clk_params {
u32 refclk;
u32 div;
u32 rnfrac;
u32 settle_time;
u32 refdiv;
u32 outdiv;
};
struct ath10k_hw_params {
u32 id;
u16 dev_id;
const char *name;
u32 patch_load_addr;
int uart_pin;
u32 otp_exe_param;
/* Type of hw cycle counter wraparound logic, for more info
* refer enum ath10k_hw_cc_wraparound_type.
*/
enum ath10k_hw_cc_wraparound_type cc_wraparound_type;
/* Some of chip expects fragment descriptor to be continuous
* memory for any TX operation. Set continuous_frag_desc flag
* for the hardware which have such requirement.
*/
bool continuous_frag_desc;
/* CCK hardware rate table mapping for the newer chipsets
* like QCA99X0, QCA4019 got revised. The CCK h/w rate values
* are in a proper order with respect to the rate/preamble
*/
bool cck_rate_map_rev2;
u32 channel_counters_freq_hz;
/* Mgmt tx descriptors threshold for limiting probe response
* frames.
*/
u32 max_probe_resp_desc_thres;
u32 tx_chain_mask;
u32 rx_chain_mask;
u32 max_spatial_stream;
u32 cal_data_len;
struct ath10k_hw_params_fw {
const char *dir;
const char *board;
size_t board_size;
size_t board_ext_size;
} fw;
/* qca99x0 family chips deliver broadcast/multicast management
* frames encrypted and expect software do decryption.
*/
bool sw_decrypt_mcast_mgmt;
const struct ath10k_hw_ops *hw_ops;
/* Number of bytes used for alignment in rx_hdr_status of rx desc. */
int decap_align_bytes;
/* hw specific clock control parameters */
const struct ath10k_hw_clk_params *hw_clk;
int target_cpu_freq;
/* Number of bytes to be discarded for each FFT sample */
int spectral_bin_discard;
/* The board may have a restricted NSS for 160 or 80+80 vs what it
* can do for 80Mhz.
*/
int vht160_mcs_rx_highest;
int vht160_mcs_tx_highest;
};
struct htt_rx_desc;
/* Defines needed for Rx descriptor abstraction */
struct ath10k_hw_ops {
int (*rx_desc_get_l3_pad_bytes)(struct htt_rx_desc *rxd);
void (*set_coverage_class)(struct ath10k *ar, s16 value);
int (*enable_pll_clk)(struct ath10k *ar);
};
extern const struct ath10k_hw_ops qca988x_ops;
extern const struct ath10k_hw_ops qca99x0_ops;
extern const struct ath10k_hw_ops qca6174_ops;
extern const struct ath10k_hw_clk_params qca6174_clk[];
static inline int
ath10k_rx_desc_get_l3_pad_bytes(struct ath10k_hw_params *hw,
struct htt_rx_desc *rxd)
{
if (hw->hw_ops->rx_desc_get_l3_pad_bytes)
return hw->hw_ops->rx_desc_get_l3_pad_bytes(rxd);
return 0;
}
/* Target specific defines for MAIN firmware */
#define TARGET_NUM_VDEVS 8
#define TARGET_NUM_PEER_AST 2
#define TARGET_NUM_WDS_ENTRIES 32
#define TARGET_DMA_BURST_SIZE 0
#define TARGET_MAC_AGGR_DELIM 0
#define TARGET_AST_SKID_LIMIT 16
#define TARGET_NUM_STATIONS 16
#define TARGET_NUM_PEERS ((TARGET_NUM_STATIONS) + \
(TARGET_NUM_VDEVS))
#define TARGET_NUM_OFFLOAD_PEERS 0
#define TARGET_NUM_OFFLOAD_REORDER_BUFS 0
#define TARGET_NUM_PEER_KEYS 2
#define TARGET_NUM_TIDS ((TARGET_NUM_PEERS) * 2)
#define TARGET_TX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2))
#define TARGET_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2))
#define TARGET_RX_TIMEOUT_LO_PRI 100
#define TARGET_RX_TIMEOUT_HI_PRI 40
#define TARGET_SCAN_MAX_PENDING_REQS 4
#define TARGET_BMISS_OFFLOAD_MAX_VDEV 3
#define TARGET_ROAM_OFFLOAD_MAX_VDEV 3
#define TARGET_ROAM_OFFLOAD_MAX_AP_PROFILES 8
#define TARGET_GTK_OFFLOAD_MAX_VDEV 3
#define TARGET_NUM_MCAST_GROUPS 0
#define TARGET_NUM_MCAST_TABLE_ELEMS 0
#define TARGET_MCAST2UCAST_MODE ATH10K_MCAST2UCAST_DISABLED
#define TARGET_TX_DBG_LOG_SIZE 1024
#define TARGET_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 0
#define TARGET_VOW_CONFIG 0
#define TARGET_NUM_MSDU_DESC (1024 + 400)
#define TARGET_MAX_FRAG_ENTRIES 0
/* Target specific defines for 10.X firmware */
#define TARGET_10X_NUM_VDEVS 16
#define TARGET_10X_NUM_PEER_AST 2
#define TARGET_10X_NUM_WDS_ENTRIES 32
#define TARGET_10X_DMA_BURST_SIZE 0
#define TARGET_10X_MAC_AGGR_DELIM 0
#define TARGET_10X_AST_SKID_LIMIT 128
#define TARGET_10X_NUM_STATIONS 128
#define TARGET_10X_TX_STATS_NUM_STATIONS 118
#define TARGET_10X_NUM_PEERS ((TARGET_10X_NUM_STATIONS) + \
(TARGET_10X_NUM_VDEVS))
#define TARGET_10X_TX_STATS_NUM_PEERS ((TARGET_10X_TX_STATS_NUM_STATIONS) + \
(TARGET_10X_NUM_VDEVS))
#define TARGET_10X_NUM_OFFLOAD_PEERS 0
#define TARGET_10X_NUM_OFFLOAD_REORDER_BUFS 0
#define TARGET_10X_NUM_PEER_KEYS 2
#define TARGET_10X_NUM_TIDS_MAX 256
#define TARGET_10X_NUM_TIDS min((TARGET_10X_NUM_TIDS_MAX), \
(TARGET_10X_NUM_PEERS) * 2)
#define TARGET_10X_TX_STATS_NUM_TIDS min((TARGET_10X_NUM_TIDS_MAX), \
(TARGET_10X_TX_STATS_NUM_PEERS) * 2)
#define TARGET_10X_TX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2))
#define TARGET_10X_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2))
#define TARGET_10X_RX_TIMEOUT_LO_PRI 100
#define TARGET_10X_RX_TIMEOUT_HI_PRI 40
#define TARGET_10X_SCAN_MAX_PENDING_REQS 4
#define TARGET_10X_BMISS_OFFLOAD_MAX_VDEV 2
#define TARGET_10X_ROAM_OFFLOAD_MAX_VDEV 2
#define TARGET_10X_ROAM_OFFLOAD_MAX_AP_PROFILES 8
#define TARGET_10X_GTK_OFFLOAD_MAX_VDEV 3
#define TARGET_10X_NUM_MCAST_GROUPS 0
#define TARGET_10X_NUM_MCAST_TABLE_ELEMS 0
#define TARGET_10X_MCAST2UCAST_MODE ATH10K_MCAST2UCAST_DISABLED
#define TARGET_10X_TX_DBG_LOG_SIZE 1024
#define TARGET_10X_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 1
#define TARGET_10X_VOW_CONFIG 0
#define TARGET_10X_NUM_MSDU_DESC (1024 + 400)
#define TARGET_10X_MAX_FRAG_ENTRIES 0
/* 10.2 parameters */
#define TARGET_10_2_DMA_BURST_SIZE 0
/* Target specific defines for WMI-TLV firmware */
#define TARGET_TLV_NUM_VDEVS 4
#define TARGET_TLV_NUM_STATIONS 32
#define TARGET_TLV_NUM_PEERS 33
#define TARGET_TLV_NUM_TDLS_VDEVS 1
#define TARGET_TLV_NUM_TIDS ((TARGET_TLV_NUM_PEERS) * 2)
#define TARGET_TLV_NUM_MSDU_DESC (1024 + 32)
#define TARGET_TLV_NUM_WOW_PATTERNS 22
/* Diagnostic Window */
#define CE_DIAG_PIPE 7
#define NUM_TARGET_CE_CONFIG_WLAN ar->hw_values->num_target_ce_config_wlan
/* Target specific defines for 10.4 firmware */
#define TARGET_10_4_NUM_VDEVS 16
#define TARGET_10_4_NUM_STATIONS 32
#define TARGET_10_4_NUM_PEERS ((TARGET_10_4_NUM_STATIONS) + \
(TARGET_10_4_NUM_VDEVS))
#define TARGET_10_4_ACTIVE_PEERS 0
#define TARGET_10_4_NUM_QCACHE_PEERS_MAX 512
#define TARGET_10_4_QCACHE_ACTIVE_PEERS 50
#define TARGET_10_4_QCACHE_ACTIVE_PEERS_PFC 35
#define TARGET_10_4_NUM_OFFLOAD_PEERS 0
#define TARGET_10_4_NUM_OFFLOAD_REORDER_BUFFS 0
#define TARGET_10_4_NUM_PEER_KEYS 2
#define TARGET_10_4_TGT_NUM_TIDS ((TARGET_10_4_NUM_PEERS) * 2)
#define TARGET_10_4_NUM_MSDU_DESC (1024 + 400)
#define TARGET_10_4_NUM_MSDU_DESC_PFC 2500
#define TARGET_10_4_AST_SKID_LIMIT 32
/* 100 ms for video, best-effort, and background */
#define TARGET_10_4_RX_TIMEOUT_LO_PRI 100
/* 40 ms for voice */
#define TARGET_10_4_RX_TIMEOUT_HI_PRI 40
#define TARGET_10_4_RX_DECAP_MODE ATH10K_HW_TXRX_NATIVE_WIFI
#define TARGET_10_4_SCAN_MAX_REQS 4
#define TARGET_10_4_BMISS_OFFLOAD_MAX_VDEV 3
#define TARGET_10_4_ROAM_OFFLOAD_MAX_VDEV 3
#define TARGET_10_4_ROAM_OFFLOAD_MAX_PROFILES 8
/* Note: mcast to ucast is disabled by default */
#define TARGET_10_4_NUM_MCAST_GROUPS 0
#define TARGET_10_4_NUM_MCAST_TABLE_ELEMS 0
#define TARGET_10_4_MCAST2UCAST_MODE 0
#define TARGET_10_4_TX_DBG_LOG_SIZE 1024
#define TARGET_10_4_NUM_WDS_ENTRIES 32
#define TARGET_10_4_DMA_BURST_SIZE 1
#define TARGET_10_4_MAC_AGGR_DELIM 0
#define TARGET_10_4_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 1
#define TARGET_10_4_VOW_CONFIG 0
#define TARGET_10_4_GTK_OFFLOAD_MAX_VDEV 3
#define TARGET_10_4_11AC_TX_MAX_FRAGS 2
#define TARGET_10_4_MAX_PEER_EXT_STATS 16
#define TARGET_10_4_SMART_ANT_CAP 0
#define TARGET_10_4_BK_MIN_FREE 0
#define TARGET_10_4_BE_MIN_FREE 0
#define TARGET_10_4_VI_MIN_FREE 0
#define TARGET_10_4_VO_MIN_FREE 0
#define TARGET_10_4_RX_BATCH_MODE 1
#define TARGET_10_4_THERMAL_THROTTLING_CONFIG 0
#define TARGET_10_4_ATF_CONFIG 0
#define TARGET_10_4_IPHDR_PAD_CONFIG 1
#define TARGET_10_4_QWRAP_CONFIG 0
/* TDLS config */
#define TARGET_10_4_NUM_TDLS_VDEVS 1
#define TARGET_10_4_NUM_TDLS_BUFFER_STA 1
#define TARGET_10_4_NUM_TDLS_SLEEP_STA 1
/* Maximum number of Copy Engine's supported */
#define CE_COUNT_MAX 12
/* Number of Copy Engines supported */
#define CE_COUNT ar->hw_values->ce_count
/*
* Granted MSIs are assigned as follows:
* Firmware uses the first
* Remaining MSIs, if any, are used by Copy Engines
* This mapping is known to both Target firmware and Host software.
* It may be changed as long as Host and Target are kept in sync.
*/
/* MSI for firmware (errors, etc.) */
#define MSI_ASSIGN_FW 0
/* MSIs for Copy Engines */
#define MSI_ASSIGN_CE_INITIAL 1
#define MSI_ASSIGN_CE_MAX ar->hw_values->msi_assign_ce_max
/* as of IP3.7.1 */
#define RTC_STATE_V_ON ar->hw_values->rtc_state_val_on
#define RTC_STATE_V_LSB 0
#define RTC_STATE_V_MASK 0x00000007
#define RTC_STATE_ADDRESS 0x0000
#define PCIE_SOC_WAKE_V_MASK 0x00000001
#define PCIE_SOC_WAKE_ADDRESS 0x0004
#define PCIE_SOC_WAKE_RESET 0x00000000
#define SOC_GLOBAL_RESET_ADDRESS 0x0008
#define RTC_SOC_BASE_ADDRESS ar->regs->rtc_soc_base_address
#define RTC_WMAC_BASE_ADDRESS ar->regs->rtc_wmac_base_address
#define MAC_COEX_BASE_ADDRESS 0x00006000
#define BT_COEX_BASE_ADDRESS 0x00007000
#define SOC_PCIE_BASE_ADDRESS 0x00008000
#define SOC_CORE_BASE_ADDRESS ar->regs->soc_core_base_address
#define WLAN_UART_BASE_ADDRESS 0x0000c000
#define WLAN_SI_BASE_ADDRESS 0x00010000
#define WLAN_GPIO_BASE_ADDRESS 0x00014000
#define WLAN_ANALOG_INTF_BASE_ADDRESS 0x0001c000
#define WLAN_MAC_BASE_ADDRESS ar->regs->wlan_mac_base_address
#define EFUSE_BASE_ADDRESS 0x00030000
#define FPGA_REG_BASE_ADDRESS 0x00039000
#define WLAN_UART2_BASE_ADDRESS 0x00054c00
#define CE_WRAPPER_BASE_ADDRESS ar->regs->ce_wrapper_base_address
#define CE0_BASE_ADDRESS ar->regs->ce0_base_address
#define CE1_BASE_ADDRESS ar->regs->ce1_base_address
#define CE2_BASE_ADDRESS ar->regs->ce2_base_address
#define CE3_BASE_ADDRESS ar->regs->ce3_base_address
#define CE4_BASE_ADDRESS ar->regs->ce4_base_address
#define CE5_BASE_ADDRESS ar->regs->ce5_base_address
#define CE6_BASE_ADDRESS ar->regs->ce6_base_address
#define CE7_BASE_ADDRESS ar->regs->ce7_base_address
#define DBI_BASE_ADDRESS 0x00060000
#define WLAN_ANALOG_INTF_PCIE_BASE_ADDRESS 0x0006c000
#define PCIE_LOCAL_BASE_ADDRESS ar->regs->pcie_local_base_address
#define SOC_RESET_CONTROL_ADDRESS 0x00000000
#define SOC_RESET_CONTROL_OFFSET 0x00000000
#define SOC_RESET_CONTROL_SI0_RST_MASK ar->regs->soc_reset_control_si0_rst_mask
#define SOC_RESET_CONTROL_CE_RST_MASK ar->regs->soc_reset_control_ce_rst_mask
#define SOC_RESET_CONTROL_CPU_WARM_RST_MASK 0x00000040
#define SOC_CPU_CLOCK_OFFSET 0x00000020
#define SOC_CPU_CLOCK_STANDARD_LSB 0
#define SOC_CPU_CLOCK_STANDARD_MASK 0x00000003
#define SOC_CLOCK_CONTROL_OFFSET 0x00000028
#define SOC_CLOCK_CONTROL_SI0_CLK_MASK 0x00000001
#define SOC_SYSTEM_SLEEP_OFFSET 0x000000c4
#define SOC_LPO_CAL_OFFSET 0x000000e0
#define SOC_LPO_CAL_ENABLE_LSB 20
#define SOC_LPO_CAL_ENABLE_MASK 0x00100000
#define SOC_LF_TIMER_CONTROL0_ADDRESS 0x00000050
#define SOC_LF_TIMER_CONTROL0_ENABLE_MASK 0x00000004
#define SOC_CHIP_ID_ADDRESS ar->regs->soc_chip_id_address
#define SOC_CHIP_ID_REV_LSB 8
#define SOC_CHIP_ID_REV_MASK 0x00000f00
#define WLAN_RESET_CONTROL_COLD_RST_MASK 0x00000008
#define WLAN_RESET_CONTROL_WARM_RST_MASK 0x00000004
#define WLAN_SYSTEM_SLEEP_DISABLE_LSB 0
#define WLAN_SYSTEM_SLEEP_DISABLE_MASK 0x00000001
#define WLAN_GPIO_PIN0_ADDRESS 0x00000028
#define WLAN_GPIO_PIN0_CONFIG_LSB 11
#define WLAN_GPIO_PIN0_CONFIG_MASK 0x00007800
#define WLAN_GPIO_PIN0_PAD_PULL_LSB 5
#define WLAN_GPIO_PIN0_PAD_PULL_MASK 0x00000060
#define WLAN_GPIO_PIN1_ADDRESS 0x0000002c
#define WLAN_GPIO_PIN1_CONFIG_MASK 0x00007800
#define WLAN_GPIO_PIN10_ADDRESS 0x00000050
#define WLAN_GPIO_PIN11_ADDRESS 0x00000054
#define WLAN_GPIO_PIN12_ADDRESS 0x00000058
#define WLAN_GPIO_PIN13_ADDRESS 0x0000005c
#define CLOCK_GPIO_OFFSET 0xffffffff
#define CLOCK_GPIO_BT_CLK_OUT_EN_LSB 0
#define CLOCK_GPIO_BT_CLK_OUT_EN_MASK 0
#define SI_CONFIG_OFFSET 0x00000000
#define SI_CONFIG_ERR_INT_LSB 19
#define SI_CONFIG_ERR_INT_MASK 0x00080000
#define SI_CONFIG_BIDIR_OD_DATA_LSB 18
#define SI_CONFIG_BIDIR_OD_DATA_MASK 0x00040000
#define SI_CONFIG_I2C_LSB 16
#define SI_CONFIG_I2C_MASK 0x00010000
#define SI_CONFIG_POS_SAMPLE_LSB 7
#define SI_CONFIG_POS_SAMPLE_MASK 0x00000080
#define SI_CONFIG_INACTIVE_DATA_LSB 5
#define SI_CONFIG_INACTIVE_DATA_MASK 0x00000020
#define SI_CONFIG_INACTIVE_CLK_LSB 4
#define SI_CONFIG_INACTIVE_CLK_MASK 0x00000010
#define SI_CONFIG_DIVIDER_LSB 0
#define SI_CONFIG_DIVIDER_MASK 0x0000000f
#define SI_CS_OFFSET 0x00000004
#define SI_CS_DONE_ERR_LSB 10
#define SI_CS_DONE_ERR_MASK 0x00000400
#define SI_CS_DONE_INT_LSB 9
#define SI_CS_DONE_INT_MASK 0x00000200
#define SI_CS_START_LSB 8
#define SI_CS_START_MASK 0x00000100
#define SI_CS_RX_CNT_LSB 4
#define SI_CS_RX_CNT_MASK 0x000000f0
#define SI_CS_TX_CNT_LSB 0
#define SI_CS_TX_CNT_MASK 0x0000000f
#define SI_TX_DATA0_OFFSET 0x00000008
#define SI_TX_DATA1_OFFSET 0x0000000c
#define SI_RX_DATA0_OFFSET 0x00000010
#define SI_RX_DATA1_OFFSET 0x00000014
#define CORE_CTRL_CPU_INTR_MASK 0x00002000
#define CORE_CTRL_PCIE_REG_31_MASK 0x00000800
#define CORE_CTRL_ADDRESS 0x0000
#define PCIE_INTR_ENABLE_ADDRESS 0x0008
#define PCIE_INTR_CAUSE_ADDRESS 0x000c
#define PCIE_INTR_CLR_ADDRESS ar->regs->pcie_intr_clr_address
#define SCRATCH_3_ADDRESS ar->regs->scratch_3_address
#define CPU_INTR_ADDRESS 0x0010
#define CCNT_TO_MSEC(ar, x) ((x) / ar->hw_params.channel_counters_freq_hz)
/* Firmware indications to the Host via SCRATCH_3 register. */
#define FW_INDICATOR_ADDRESS ar->regs->fw_indicator_address
#define FW_IND_EVENT_PENDING 1
#define FW_IND_INITIALIZED 2
#define FW_IND_HOST_READY 0x80000000
/* HOST_REG interrupt from firmware */
#define PCIE_INTR_FIRMWARE_MASK ar->regs->pcie_intr_fw_mask
#define PCIE_INTR_CE_MASK_ALL ar->regs->pcie_intr_ce_mask_all
#define DRAM_BASE_ADDRESS 0x00400000
#define PCIE_BAR_REG_ADDRESS 0x40030
#define MISSING 0
#define SYSTEM_SLEEP_OFFSET SOC_SYSTEM_SLEEP_OFFSET
#define WLAN_SYSTEM_SLEEP_OFFSET SOC_SYSTEM_SLEEP_OFFSET
#define WLAN_RESET_CONTROL_OFFSET SOC_RESET_CONTROL_OFFSET
#define CLOCK_CONTROL_OFFSET SOC_CLOCK_CONTROL_OFFSET
#define CLOCK_CONTROL_SI0_CLK_MASK SOC_CLOCK_CONTROL_SI0_CLK_MASK
#define RESET_CONTROL_MBOX_RST_MASK MISSING
#define RESET_CONTROL_SI0_RST_MASK SOC_RESET_CONTROL_SI0_RST_MASK
#define GPIO_BASE_ADDRESS WLAN_GPIO_BASE_ADDRESS
#define GPIO_PIN0_OFFSET WLAN_GPIO_PIN0_ADDRESS
#define GPIO_PIN1_OFFSET WLAN_GPIO_PIN1_ADDRESS
#define GPIO_PIN0_CONFIG_LSB WLAN_GPIO_PIN0_CONFIG_LSB
#define GPIO_PIN0_CONFIG_MASK WLAN_GPIO_PIN0_CONFIG_MASK
#define GPIO_PIN0_PAD_PULL_LSB WLAN_GPIO_PIN0_PAD_PULL_LSB
#define GPIO_PIN0_PAD_PULL_MASK WLAN_GPIO_PIN0_PAD_PULL_MASK
#define GPIO_PIN1_CONFIG_MASK WLAN_GPIO_PIN1_CONFIG_MASK
#define SI_BASE_ADDRESS WLAN_SI_BASE_ADDRESS
#define SCRATCH_BASE_ADDRESS SOC_CORE_BASE_ADDRESS
#define LOCAL_SCRATCH_OFFSET 0x18
#define CPU_CLOCK_OFFSET SOC_CPU_CLOCK_OFFSET
#define LPO_CAL_OFFSET SOC_LPO_CAL_OFFSET
#define GPIO_PIN10_OFFSET WLAN_GPIO_PIN10_ADDRESS
#define GPIO_PIN11_OFFSET WLAN_GPIO_PIN11_ADDRESS
#define GPIO_PIN12_OFFSET WLAN_GPIO_PIN12_ADDRESS
#define GPIO_PIN13_OFFSET WLAN_GPIO_PIN13_ADDRESS
#define CPU_CLOCK_STANDARD_LSB SOC_CPU_CLOCK_STANDARD_LSB
#define CPU_CLOCK_STANDARD_MASK SOC_CPU_CLOCK_STANDARD_MASK
#define LPO_CAL_ENABLE_LSB SOC_LPO_CAL_ENABLE_LSB
#define LPO_CAL_ENABLE_MASK SOC_LPO_CAL_ENABLE_MASK
#define ANALOG_INTF_BASE_ADDRESS WLAN_ANALOG_INTF_BASE_ADDRESS
#define MBOX_BASE_ADDRESS MISSING
#define INT_STATUS_ENABLE_ERROR_LSB MISSING
#define INT_STATUS_ENABLE_ERROR_MASK MISSING
#define INT_STATUS_ENABLE_CPU_LSB MISSING
#define INT_STATUS_ENABLE_CPU_MASK MISSING
#define INT_STATUS_ENABLE_COUNTER_LSB MISSING
#define INT_STATUS_ENABLE_COUNTER_MASK MISSING
#define INT_STATUS_ENABLE_MBOX_DATA_LSB MISSING
#define INT_STATUS_ENABLE_MBOX_DATA_MASK MISSING
#define ERROR_STATUS_ENABLE_RX_UNDERFLOW_LSB MISSING
#define ERROR_STATUS_ENABLE_RX_UNDERFLOW_MASK MISSING
#define ERROR_STATUS_ENABLE_TX_OVERFLOW_LSB MISSING
#define ERROR_STATUS_ENABLE_TX_OVERFLOW_MASK MISSING
#define COUNTER_INT_STATUS_ENABLE_BIT_LSB MISSING
#define COUNTER_INT_STATUS_ENABLE_BIT_MASK MISSING
#define INT_STATUS_ENABLE_ADDRESS MISSING
#define CPU_INT_STATUS_ENABLE_BIT_LSB MISSING
#define CPU_INT_STATUS_ENABLE_BIT_MASK MISSING
#define HOST_INT_STATUS_ADDRESS MISSING
#define CPU_INT_STATUS_ADDRESS MISSING
#define ERROR_INT_STATUS_ADDRESS MISSING
#define ERROR_INT_STATUS_WAKEUP_MASK MISSING
#define ERROR_INT_STATUS_WAKEUP_LSB MISSING
#define ERROR_INT_STATUS_RX_UNDERFLOW_MASK MISSING
#define ERROR_INT_STATUS_RX_UNDERFLOW_LSB MISSING
#define ERROR_INT_STATUS_TX_OVERFLOW_MASK MISSING
#define ERROR_INT_STATUS_TX_OVERFLOW_LSB MISSING
#define COUNT_DEC_ADDRESS MISSING
#define HOST_INT_STATUS_CPU_MASK MISSING
#define HOST_INT_STATUS_CPU_LSB MISSING
#define HOST_INT_STATUS_ERROR_MASK MISSING
#define HOST_INT_STATUS_ERROR_LSB MISSING
#define HOST_INT_STATUS_COUNTER_MASK MISSING
#define HOST_INT_STATUS_COUNTER_LSB MISSING
#define RX_LOOKAHEAD_VALID_ADDRESS MISSING
#define WINDOW_DATA_ADDRESS MISSING
#define WINDOW_READ_ADDR_ADDRESS MISSING
#define WINDOW_WRITE_ADDR_ADDRESS MISSING
#define QCA9887_1_0_I2C_SDA_GPIO_PIN 5
#define QCA9887_1_0_I2C_SDA_PIN_CONFIG 3
#define QCA9887_1_0_SI_CLK_GPIO_PIN 17
#define QCA9887_1_0_SI_CLK_PIN_CONFIG 3
#define QCA9887_1_0_GPIO_ENABLE_W1TS_LOW_ADDRESS 0x00000010
#define QCA9887_EEPROM_SELECT_READ 0xa10000a0
#define QCA9887_EEPROM_ADDR_HI_MASK 0x0000ff00
#define QCA9887_EEPROM_ADDR_HI_LSB 8
#define QCA9887_EEPROM_ADDR_LO_MASK 0x00ff0000
#define QCA9887_EEPROM_ADDR_LO_LSB 16
#define MBOX_RESET_CONTROL_ADDRESS 0x00000000
#define MBOX_HOST_INT_STATUS_ADDRESS 0x00000800
#define MBOX_HOST_INT_STATUS_ERROR_LSB 7
#define MBOX_HOST_INT_STATUS_ERROR_MASK 0x00000080
#define MBOX_HOST_INT_STATUS_CPU_LSB 6
#define MBOX_HOST_INT_STATUS_CPU_MASK 0x00000040
#define MBOX_HOST_INT_STATUS_COUNTER_LSB 4
#define MBOX_HOST_INT_STATUS_COUNTER_MASK 0x00000010
#define MBOX_CPU_INT_STATUS_ADDRESS 0x00000801
#define MBOX_ERROR_INT_STATUS_ADDRESS 0x00000802
#define MBOX_ERROR_INT_STATUS_WAKEUP_LSB 2
#define MBOX_ERROR_INT_STATUS_WAKEUP_MASK 0x00000004
#define MBOX_ERROR_INT_STATUS_RX_UNDERFLOW_LSB 1
#define MBOX_ERROR_INT_STATUS_RX_UNDERFLOW_MASK 0x00000002
#define MBOX_ERROR_INT_STATUS_TX_OVERFLOW_LSB 0
#define MBOX_ERROR_INT_STATUS_TX_OVERFLOW_MASK 0x00000001
#define MBOX_COUNTER_INT_STATUS_ADDRESS 0x00000803
#define MBOX_COUNTER_INT_STATUS_COUNTER_LSB 0
#define MBOX_COUNTER_INT_STATUS_COUNTER_MASK 0x000000ff
#define MBOX_RX_LOOKAHEAD_VALID_ADDRESS 0x00000805
#define MBOX_INT_STATUS_ENABLE_ADDRESS 0x00000828
#define MBOX_INT_STATUS_ENABLE_ERROR_LSB 7
#define MBOX_INT_STATUS_ENABLE_ERROR_MASK 0x00000080
#define MBOX_INT_STATUS_ENABLE_CPU_LSB 6
#define MBOX_INT_STATUS_ENABLE_CPU_MASK 0x00000040
#define MBOX_INT_STATUS_ENABLE_INT_LSB 5
#define MBOX_INT_STATUS_ENABLE_INT_MASK 0x00000020
#define MBOX_INT_STATUS_ENABLE_COUNTER_LSB 4
#define MBOX_INT_STATUS_ENABLE_COUNTER_MASK 0x00000010
#define MBOX_INT_STATUS_ENABLE_MBOX_DATA_LSB 0
#define MBOX_INT_STATUS_ENABLE_MBOX_DATA_MASK 0x0000000f
#define MBOX_CPU_INT_STATUS_ENABLE_ADDRESS 0x00000819
#define MBOX_CPU_INT_STATUS_ENABLE_BIT_LSB 0
#define MBOX_CPU_INT_STATUS_ENABLE_BIT_MASK 0x000000ff
#define MBOX_ERROR_STATUS_ENABLE_ADDRESS 0x0000081a
#define MBOX_ERROR_STATUS_ENABLE_RX_UNDERFLOW_LSB 1
#define MBOX_ERROR_STATUS_ENABLE_RX_UNDERFLOW_MASK 0x00000002
#define MBOX_ERROR_STATUS_ENABLE_TX_OVERFLOW_LSB 0
#define MBOX_ERROR_STATUS_ENABLE_TX_OVERFLOW_MASK 0x00000001
#define MBOX_COUNTER_INT_STATUS_ENABLE_ADDRESS 0x0000081b
#define MBOX_COUNTER_INT_STATUS_ENABLE_BIT_LSB 0
#define MBOX_COUNTER_INT_STATUS_ENABLE_BIT_MASK 0x000000ff
#define MBOX_COUNT_ADDRESS 0x00000820
#define MBOX_COUNT_DEC_ADDRESS 0x00000840
#define MBOX_WINDOW_DATA_ADDRESS 0x00000874
#define MBOX_WINDOW_WRITE_ADDR_ADDRESS 0x00000878
#define MBOX_WINDOW_READ_ADDR_ADDRESS 0x0000087c
#define MBOX_CPU_DBG_SEL_ADDRESS 0x00000883
#define MBOX_CPU_DBG_ADDRESS 0x00000884
#define MBOX_RTC_BASE_ADDRESS 0x00000000
#define MBOX_GPIO_BASE_ADDRESS 0x00005000
#define MBOX_MBOX_BASE_ADDRESS 0x00008000
#define RTC_STATE_V_GET(x) (((x) & RTC_STATE_V_MASK) >> RTC_STATE_V_LSB)
/* Register definitions for first generation ath10k cards. These cards include
* a mac thich has a register allocation similar to ath9k and at least some
* registers including the ones relevant for modifying the coverage class are
* identical to the ath9k definitions.
* These registers are usually managed by the ath10k firmware. However by
* overriding them it is possible to support coverage class modifications.
*/
#define WAVE1_PCU_ACK_CTS_TIMEOUT 0x8014
#define WAVE1_PCU_ACK_CTS_TIMEOUT_MAX 0x00003FFF
#define WAVE1_PCU_ACK_CTS_TIMEOUT_ACK_MASK 0x00003FFF
#define WAVE1_PCU_ACK_CTS_TIMEOUT_ACK_LSB 0
#define WAVE1_PCU_ACK_CTS_TIMEOUT_CTS_MASK 0x3FFF0000
#define WAVE1_PCU_ACK_CTS_TIMEOUT_CTS_LSB 16
#define WAVE1_PCU_GBL_IFS_SLOT 0x1070
#define WAVE1_PCU_GBL_IFS_SLOT_MASK 0x0000FFFF
#define WAVE1_PCU_GBL_IFS_SLOT_MAX 0x0000FFFF
#define WAVE1_PCU_GBL_IFS_SLOT_LSB 0
#define WAVE1_PCU_GBL_IFS_SLOT_RESV0 0xFFFF0000
#define WAVE1_PHYCLK 0x801C
#define WAVE1_PHYCLK_USEC_MASK 0x0000007F
#define WAVE1_PHYCLK_USEC_LSB 0
/* qca6174 PLL offset/mask */
#define SOC_CORE_CLK_CTRL_OFFSET 0x00000114
#define SOC_CORE_CLK_CTRL_DIV_LSB 0
#define SOC_CORE_CLK_CTRL_DIV_MASK 0x00000007
#define EFUSE_OFFSET 0x0000032c
#define EFUSE_XTAL_SEL_LSB 8
#define EFUSE_XTAL_SEL_MASK 0x00000700
#define BB_PLL_CONFIG_OFFSET 0x000002f4
#define BB_PLL_CONFIG_FRAC_LSB 0
#define BB_PLL_CONFIG_FRAC_MASK 0x0003ffff
#define BB_PLL_CONFIG_OUTDIV_LSB 18
#define BB_PLL_CONFIG_OUTDIV_MASK 0x001c0000
#define WLAN_PLL_SETTLE_OFFSET 0x0018
#define WLAN_PLL_SETTLE_TIME_LSB 0
#define WLAN_PLL_SETTLE_TIME_MASK 0x000007ff
#define WLAN_PLL_CONTROL_OFFSET 0x0014
#define WLAN_PLL_CONTROL_DIV_LSB 0
#define WLAN_PLL_CONTROL_DIV_MASK 0x000003ff
#define WLAN_PLL_CONTROL_REFDIV_LSB 10
#define WLAN_PLL_CONTROL_REFDIV_MASK 0x00003c00
#define WLAN_PLL_CONTROL_BYPASS_LSB 16
#define WLAN_PLL_CONTROL_BYPASS_MASK 0x00010000
#define WLAN_PLL_CONTROL_NOPWD_LSB 18
#define WLAN_PLL_CONTROL_NOPWD_MASK 0x00040000
#define RTC_SYNC_STATUS_OFFSET 0x0244
#define RTC_SYNC_STATUS_PLL_CHANGING_LSB 5
#define RTC_SYNC_STATUS_PLL_CHANGING_MASK 0x00000020
/* qca6174 PLL offset/mask end */
#endif /* _HW_H_ */