blob: ef81b49cfc8a35886b3def4e5d39a2a22ea03b87 [file] [log] [blame] [edit]
/*
* Copyright (C) 2005 Texas Instruments.
* Jian Zhang <jzhang@ti.com>
* Richard Woodruff <r-woodruff2@ti.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/arch/omap2420.h>
#include <asm/arch/bits.h>
#include <asm/arch/mem.h>
#include <asm/arch/sys_info.h>
#include <asm/arch/clocks.h>
static void wait_for_command_complete(unsigned int wd_base);
static void watchdog_init(void);
static void peripheral_enable(void);
static void muxSetupUART1(void);
static u32 get_cpu_rev(void);
/*******************************************************
* Routine: delay
* Description: spinning delay to use before udelay works
******************************************************/
static inline void delay (unsigned long loops)
{
__asm__ volatile ("1:\n"
"subs %0, %1, #1\n"
"bne 1b":"=r" (loops):"0" (loops));
}
/*****************************************
* Routine: board_init
* Description: Early hardware init.
*****************************************/
int board_init (void)
{
return 0;
}
#ifdef CFG_SDRAM_DDR
void
config_sdram_ddr(u32 rev)
{
/* ball D11, mode 0 */
__raw_writeb(0x08, 0x48000032);
/* SDRC_CS0 Configuration */
if (rev == CPU_2420_2422_ES1) {
__raw_writel(H4_2422_SDRC_MDCFG_0_DDR, SDRC_MCFG_0);
__raw_writel(H4_2422_SDRC_SHARING, SDRC_SHARING);
} else {
__raw_writel(H4_2420_SDRC_MDCFG_0_DDR, SDRC_MCFG_0);
__raw_writel(H4_2420_SDRC_SHARING, SDRC_SHARING);
}
__raw_writel(H4_242x_SDRC_RFR_CTRL_ES1, SDRC_RFR_CTRL);
__raw_writel(H4_242x_SDRC_ACTIM_CTRLA_0_ES1, SDRC_ACTIM_CTRLA_0);
__raw_writel(H4_242x_SDRC_ACTIM_CTRLB_0_ES1, SDRC_ACTIM_CTRLB_0);
/* Manual Command sequence */
__raw_writel(CMD_NOP, SDRC_MANUAL_0);
__raw_writel(CMD_PRECHARGE, SDRC_MANUAL_0);
__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0);
__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0);
/*
* CS0 SDRC Mode Register
* Burst length = 4 - DDR memory
* Serial mode
* CAS latency = 3
*/
__raw_writel(0x00000032, SDRC_MR_0);
/* SDRC DLLA control register */
/* Delay is 90 degrees */
if (rev == CPU_2420_2422_ES1) {
/* Enable DLL, Load counter with 115 (middle of range) */
__raw_writel(0x00000002, SDRC_DLLA_CTRL);
/* Enable DLL, Load counter with 128 (middle of range) */
__raw_writel(0x00000002, SDRC_DLLB_CTRL);
} else {
/* Enable DLL, Load counter with 115 (middle of range) */
__raw_writel(0x00000008, SDRC_DLLA_CTRL); // ES2.x
/* Enable DLL, Load counter with 128 (middle of range) */
__raw_writel(0x00000008, SDRC_DLLB_CTRL); // ES2.x
}
}
#endif // CFG_SDRAM_DDR
#ifdef CFG_SDRAM_COMBO
void
config_sdram_combo(u32 rev)
{
u32 dllctrl=0;
/* ball C12, mode 0 */
__raw_writeb(0x00, 0x480000a1);
/* ball D11, mode 0 */
__raw_writeb(0x00, 0x48000032);
/* ball B13, mode 0 - for CKE1 (not needed rkw for combo) */
__raw_writeb(0x00, 0x480000a3);
/*configure sdrc 32 bit for COMBO ddr sdram. Issue soft reset */
__raw_writel(0x00000012, SDRC_SYSCONFIG);
delay(200000);
__raw_writel(0x00000010, SDRC_SYSCONFIG);
/* SDRCTriState: no Tris */
/* CS0MuxCfg: 000 (32-bit SDRAM on D31..0) */
__raw_writel(H4_2420_SDRC_SHARING, SDRC_SHARING);
/* CS0 SDRC Memory Configuration, */
/* DDR-SDRAM, External SDRAM is x32bit, */
/* Configure to MUX9: 1x8Mbx32 */
__raw_writel(H4_2420_COMBO_MDCFG_0_DDR, SDRC_MCFG_0);
__raw_writel(H4_2420_SDRC_ACTIM_CTRLA_0, SDRC_ACTIM_CTRLA_0);
__raw_writel(H4_2420_SDRC_ACTIM_CTRLB_0, SDRC_ACTIM_CTRLB_0);
__raw_writel(H4_242x_SDRC_RFR_CTRL_ES1, SDRC_RFR_CTRL);
/* Manual Command sequence */
__raw_writel(CMD_NOP, SDRC_MANUAL_0);
__raw_writel(CMD_PRECHARGE, SDRC_MANUAL_0);
__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0);
__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0);
/* CS0 SDRC Mode Register */
/* Burst length = 4 - DDR memory */
/* Serial mode */
/* CAS latency = 3 */
__raw_writel(H4_2422_SDRC_MR_0_DDR, SDRC_MR_0);
/* CS1 SDRC Memory Configuration, */
/* DDR-SDRAM, External SDRAM is x32bit, */
/* Configure to MUX9: 1x8Mbx32 */
__raw_writel(H4_2420_COMBO_MDCFG_0_DDR, SDRC_MCFG_1);
__raw_writel(H4_242X_SDRC_ACTIM_CTRLA_0_100MHz, SDRC_ACTIM_CTRLA_1);
__raw_writel(H4_2420_SDRC_ACTIM_CTRLB_0, SDRC_ACTIM_CTRLB_1);
__raw_writel(H4_242x_SDRC_RFR_CTRL_ES1, 0x680090d4);
/* Manual Command sequence */
__raw_writel(CMD_NOP, SDRC_MANUAL_1);
__raw_writel(CMD_PRECHARGE, SDRC_MANUAL_1);
__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_1);
__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_1);
/* CS1 SDRC Mode Register */
/* Burst length = 4 - DDR memory */
/* Serial mode */
/* CAS latency = 3 */
__raw_writel(H4_2422_SDRC_MR_0_DDR, SDRC_MR_1);
/* SDRC DLLA control register */
/* Delay is 90 degrees */
if (rev == CPU_242X_ES1)
dllctrl = (BIT0|BIT3);
else
dllctrl = BIT0;
if (rev == CPU_2420_2422_ES1) {
/* Enable DLL, Load counter with 115 (middle of range) */
__raw_writel(0x00007306, SDRC_DLLA_CTRL);
__raw_writel(0x00007302, SDRC_DLLA_CTRL);
/* Enable DLL, Load counter with 128 (middle of range) */
__raw_writel(0x00007306, SDRC_DLLB_CTRL); /* load ctr value */
__raw_writel(0x00007302, SDRC_DLLB_CTRL); /* lock and go */
}
else {
/* Enable DLL, Load counter with 115 (middle of range) */
__raw_writel(H4_2420_SDRC_DLLAB_CTRL, SDRC_DLLA_CTRL); // ES2.x
__raw_writel(H4_2420_SDRC_DLLAB_CTRL & ~(LOADDLL|dllctrl), SDRC_DLLA_CTRL); // ES2.x
__raw_writel(H4_2420_SDRC_DLLAB_CTRL, SDRC_DLLB_CTRL); // ES2.x ?
__raw_writel(H4_2420_SDRC_DLLAB_CTRL & ~(LOADDLL|dllctrl), SDRC_DLLB_CTRL); // ES2.x
}
}
#endif // CFG_SDRAM_COMBO
#ifdef CFG_SDRAM_SDR
void
config_sdram_sdr(u32 rev)
{
u32 dllctrl=0;
/* ball D11, mode 0 */
__raw_writeb(0x00, 0x48000032);
__raw_writel(0x00000012, SDRC_SYSCONFIG);
delay(200000);
__raw_writel(0x00000010, SDRC_SYSCONFIG);
/* Chip-level shared interface management */
/* SDRCTriState: no Tris */
/* CS0MuxCfg: 000 (32-bit SDRAM on D31..0) */
/* CS1MuxCfg: 000 (32-bit SDRAM on D31..0) */
if (rev == CPU_2420_2422_ES1)
__raw_writel(H4_2422_SDRC_SHARING, SDRC_SHARING);
else
__raw_writel(H4_2420_SDRC_SHARING, SDRC_SHARING);
/* CS0 SDRC Memory Configuration, */
/* DDR-SDRAM, External SDRAM is x32bit, */
/* Configure to MUX14: 32Mbx32 */
__raw_writel(H4_2420_SDRC_MDCFG_0_SDR, SDRC_MCFG_0); /* diff from combo case */
__raw_writel(H4_2420_SDRC_ACTIM_CTRLA_0, SDRC_ACTIM_CTRLA_0);
__raw_writel(H4_2420_SDRC_ACTIM_CTRLB_0, SDRC_ACTIM_CTRLB_0);
__raw_writel(H4_242x_SDRC_RFR_CTRL_ES1, SDRC_RFR_CTRL);
/* Manual Command sequence */
__raw_writel(CMD_NOP, SDRC_MANUAL_0);
__raw_writel(CMD_PRECHARGE, SDRC_MANUAL_0);
__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0);
__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0);
/* CS0 SDRC Mode Register */
/* Burst length = 2 - SDR memory */
/* Serial mode */
/* CAS latency = 3 */
__raw_writel(H4_2420_SDRC_MR_0_SDR, SDRC_MR_0); /* diff from combo case */
/* SDRC DLLA control register */
/* Enable DLL, Load counter with 115 (middle of range) */
/* Delay is 90 degrees */
if (rev == CPU_242X_ES1)
dllctrl = (BIT0|BIT3);
else
dllctrl = BIT0;
if (rev == CPU_2420_2422_ES1) {
__raw_writel(0x00007306, SDRC_DLLA_CTRL);
__raw_writel(0x00007302, SDRC_DLLA_CTRL);
/* Enable DLL, Load counter with 128 (middle of range) */
__raw_writel(0x00007306, SDRC_DLLB_CTRL); /* load ctr value */
__raw_writel(0x00007302, SDRC_DLLB_CTRL); /* lock and go */
}
else {
__raw_writel(H4_2420_SDRC_DLLAB_CTRL, SDRC_DLLA_CTRL); // ES2.x
__raw_writel(H4_2420_SDRC_DLLAB_CTRL & ~(LOADDLL|dllctrl), SDRC_DLLA_CTRL); // ES2.x
/* Enable DLL, Load counter with 128 (middle of range) */
__raw_writel(H4_2420_SDRC_DLLAB_CTRL, SDRC_DLLB_CTRL); // ES2.x
__raw_writel(H4_2420_SDRC_DLLAB_CTRL & ~(LOADDLL|dllctrl), SDRC_DLLB_CTRL); // ES2.x
}
}
#endif // CFG_SDRAM_SDR
#ifdef CFG_SDRAM_STACKED
void
config_sdram_stacked(u32 rev)
{
/* Pin Muxing for SDRC */
__raw_writeb(0x00, 0x480000a1); /* mux mode 0 (CS1) */
__raw_writeb(0x00, 0x480000a3); /* mux mode 0 (CKE1) */
__raw_writeb(0x00, 0x48000032); /* connect sdrc_a12 */
__raw_writeb(0x00, 0x48000031); /* connect sdrc_a13 */
/* configure sdrc 32 bit for COMBO ddr sdram */
__raw_writel(0x00000010, SDRC_SYSCONFIG); /* no idle ack and RESET enable */
delay(200000);
__raw_writel(0x00000010, SDRC_SYSCONFIG); /* smart idle mode */
/* SDRC_SHARING */
/* U-boot is writing 0x00000100 though (H4_2420_SDRC_SHARING ) */
//__raw_writel(H4_2420_SDRC_SHARING, SDRC_SHARING);
__raw_writel(0x00004900, SDRC_SHARING);
/* SDRC_CS0 Configuration */
/* None for ES2.1 */
/* SDRC_CS1 Configuration */
__raw_writel(0x00000000, SDRC_CS_CFG); /* Remap CS1 to 0x80000000 */
/* Disable power down of CKE */
__raw_writel(0x00000085, SDRC_POWER);
__raw_writel(0x01A02019, SDRC_MCFG_1); /* SDRC_MCFG1 */
__raw_writel(0x0003DD03, SDRC_RFR_CTRL1); /* SDRC_RFR_CTRL1 */
__raw_writel(0x92DDC485, SDRC_ACTIM_CTRLA_1); /* SDRC_ACTIM_CTRLA0 */
__raw_writel(0x00000014, SDRC_ACTIM_CTRLB_1); /* SDRC_ACTIM_CTRLB0 */
/*Manual Command sequence */
__raw_writel(CMD_NOP, SDRC_MANUAL_1);
__raw_writel(CMD_PRECHARGE, SDRC_MANUAL_1);
__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_1);
__raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_1);
/* CS0 SDRC Mode Register */
/* Burst length = 4 - DDR memory */
/* Serial mode */
/* CAS latency = 3 */
__raw_writel(0x00000032, SDRC_MR_1);
__raw_writel(0x00000020, SDRC_EMR2_1); /* weak-strength driver */
/* SDRC DLLA control register */
/* Delay is 90 degrees */
if (rev == CPU_2420_2422_ES1) {
/* Enable DLL, Load counter with 115 (middle of range) */
__raw_writel(0x00007302, SDRC_DLLA_CTRL);
/* Enable DLL, Load counter with 128 (middle of range) */
__raw_writel(0x00007302, SDRC_DLLB_CTRL);
}
else {
/* Enable DLL, Load counter with 115 (middle of range) */
__raw_writel(0x00003108, SDRC_DLLA_CTRL); // ES2.x
/* Enable DLL, Load counter with 128 (middle of range) */
__raw_writel(0x00003108, SDRC_DLLB_CTRL); // ES2.x
}
}
#endif // CFG_SDRAM_STACKED
/**********************************************************
* Routine: s_init
* Description: Does early system init of muxing and clocks.
* - Called at time when only stack is available.
**********************************************************/
int s_init(int skip)
{
u32 rev;
rev = get_cpu_rev();
watchdog_init();
muxSetupUART1();
delay(100);
/*DPLL out = 2x DPLL --> core clock */
__raw_writel(DPLL_OUT, CM_CLKSEL2_PLL);
/*DPLL into low power bypass (others off) */
__raw_writel(0x00000001, CM_CLKEN_PLL);
/*MPU core clock = Core /2 = 300 */
__raw_writel(MPU_DIV, CM_CLKSEL_MPU);
/*DSPif=200, DSPif=100, IVA=200 */
__raw_writel(DSP_DIV, CM_CLKSEL_DSP);
/*GFX clock (L3/2) 50MHz */
__raw_writel(GFX_DIV, CM_CLKSEL_GFX);
/*L3=100, L4=100, DisplaySS=50 Vlync=96Mhz,ssi=100, usb=50 */
__raw_writel(BUS_DIV, CM_CLKSEL1_CORE);
/*12MHz apll src, 12/(1+1)*50=300 */
__raw_writel(DPLL_VAL, CM_CLKSEL1_PLL);
/*Valid the configuration */
__raw_writel(0x00000001, PRCM_CLKCFG_CTRL);
delay(1000);
/*Enable DPLL=300, 96MHz APLL locked. */
__raw_writel(0x0000000F, CM_CLKEN_PLL);
delay(200000);
#ifdef CFG_SDRAM_DDR
config_sdram_ddr(rev);
#elif defined(CFG_SDRAM_COMBO)
config_sdram_combo(rev);
#elif defined(CFG_SDRAM_SDR)
config_sdram_sdr(rev);
#elif defined(CFG_SDRAM_STACKED)
config_sdram_stacked(rev);
#else
#error SDRAM type not supported
#endif
delay(20000);
peripheral_enable();
return(0);
}
/*******************************************************
* Routine: misc_init_r
* Description: Init ethernet (done here so udelay works)
********************************************************/
int misc_init_r (void)
{
return(0);
}
/****************************************
* Routine: watchdog_init
* Description: Shut down watch dogs
*****************************************/
static void watchdog_init(void)
{
#define GP (BIT8|BIT9)
/* There are 4 watch dogs. 1 secure, and 3 general purpose.
* I would expect that the ROM takes care of the secure one,
* but we will try also. Of the 3 GP ones, 1 can reset us
* directly, the other 2 only generate MPU interrupts.
*/
__raw_writel(WD_UNLOCK1 ,WD2_BASE+WSPR);
wait_for_command_complete(WD2_BASE);
__raw_writel(WD_UNLOCK2 ,WD2_BASE+WSPR);
#if MPU_WD_CLOCKED /* value 0x10 stick on aptix, BIT4 polarity seems oppsite*/
__raw_writel(WD_UNLOCK1 ,WD3_BASE+WSPR);
wait_for_command_complete(WD3_BASE);
__raw_writel(WD_UNLOCK2 ,WD3_BASE+WSPR);
__raw_writel(WD_UNLOCK1 ,WD4_BASE+WSPR);
wait_for_command_complete(WD4_BASE);
__raw_writel(WD_UNLOCK2 ,WD4_BASE+WSPR);
#endif
}
/******************************************************
* Routine: wait_for_command_complete
* Description: Wait for posting to finish on watchdog
******************************************************/
static void wait_for_command_complete(unsigned int wd_base)
{
int pending = 1;
do {
pending = __raw_readl(wd_base+WWPS);
} while (pending);
}
/**********************************************
* Routine: dram_init
* Description: sets uboots idea of sdram size
**********************************************/
int dram_init (void)
{
return 0;
}
/*****************************************************************
* Routine: peripheral_enable
* Description: Enable the clks & power for perifs (GPT2, UART1,...)
******************************************************************/
static void peripheral_enable(void)
{
unsigned int v, if_clks=0, func_clks=0;
/* Enable GP2 timer.*/
if_clks |= BIT4;
func_clks |= BIT4;
v = __raw_readl(CM_CLKSEL2_CORE) | 0x4; /* Sys_clk input OMAP2420_GPT2 */
__raw_writel(v, CM_CLKSEL2_CORE);
__raw_writel(0x1, CM_CLKSEL_WKUP);
#ifdef CFG_NS16550
/* Enable UART1 clock */
func_clks |= BIT21;
if_clks |= BIT21;
#endif
v = __raw_readl(CM_ICLKEN1_CORE) | if_clks; /* Interface clocks on */
__raw_writel(v,CM_ICLKEN1_CORE );
v = __raw_readl(CM_FCLKEN1_CORE) | func_clks; /* Functional Clocks on */
__raw_writel(v, CM_FCLKEN1_CORE);
delay(1000);
#ifndef KERNEL_UPDATED
{
#define V1 0xffffffff
#define V2 0x00000007
__raw_writel(V1, CM_FCLKEN1_CORE);
__raw_writel(V2, CM_FCLKEN2_CORE);
__raw_writel(V1, CM_ICLKEN1_CORE);
__raw_writel(V1, CM_ICLKEN2_CORE);
}
#endif
}
/* Pin Muxing registers used for UART1 */
#define CONTROL_PADCONF_UART1_CTS ((volatile unsigned char *)0x480000C5)
#define CONTROL_PADCONF_UART1_RTS ((volatile unsigned char *)0x480000C6)
#define CONTROL_PADCONF_UART1_TX ((volatile unsigned char *)0x480000C7)
#define CONTROL_PADCONF_UART1_RX ((volatile unsigned char *)0x480000C8)
/****************************************
* Routine: muxSetupUART1 (ostboot)
* Description: Set up uart1 muxing
*****************************************/
static void muxSetupUART1(void)
{
volatile unsigned char *MuxConfigReg;
/* UART1_CTS pin configuration, PIN = D21 */
MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_CTS;
*MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
/* UART1_RTS pin configuration, PIN = H21 */
MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RTS;
*MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
/* UART1_TX pin configuration, PIN = L20 */
MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_TX;
*MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
/* UART1_RX pin configuration, PIN = T21 */
MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RX;
*MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
}
int nand_init(void)
{
u32 rev;
rev = get_cpu_rev();
/* GPMC pin muxing */
(*(volatile int*)0x48000070) &= 0x000000FF;
(*(volatile int*)0x48000074) &= 0x00000000;
(*(volatile int*)0x48000078) &= 0x00000000;
(*(volatile int*)0x4800007C) &= 0x00000000;
(*(volatile int*)0x48000080) &= 0xFF000000;
/* GPMC_IO_DIR */
(*(volatile int*)0x4800008C) = 0x19000000;
/* GPMC Configuration */
(*(volatile int*)0x6800A010) = 0x0000000A;
while (((*(volatile int *)0x6800A014) & 0x00000001) == 0);
(*(volatile int*)0x6800A050) = 0x00000001;
(*(volatile int*)0x6800A060) = 0x00001800;
(*(volatile int*)0x6800A064) = 0x00141400;
(*(volatile int*)0x6800A068) = 0x00141400;
(*(volatile int*)0x6800A06C) = 0x0F010F01;
(*(volatile int*)0x6800A070) = 0x010C1414;
(*(volatile int*)0x6800A074) = 0x00000A80;
(*(volatile int*)0x6800A078) = 0x00000C44; //base 0x04000000
(*(volatile int*)0x6800A0A8) = 0x00000000;
delay(1000);
#ifdef CFG_SDRAM_STACKED
(*(volatile int*)0x6800A090) = 0x00011000;
#else
(*(volatile int*)0x6800A090) = 0x00011200;
#endif
(*(volatile int*)0x6800A094) = 0x001f1f00;
(*(volatile int*)0x6800A098) = 0x00080802;
(*(volatile int*)0x6800A09C) = 0x1C091C09;
(*(volatile int*)0x6800A0A0) = 0x031A1F1F;
(*(volatile int*)0x6800A0A4) = 0x000003C2;
(*(volatile int*)0x6800A0A8) = 0x00000F48;
if (rev != CPU_2420_2422_ES1)
(*(volatile int*)0x6800A040) = 0x1FF0; // es2.x
if (nand_chip()){
printf("Unsupported Chip!\n");
return 1;
}
return 0;
}
/******************************************
* get_cpu_rev(void) - extract version info
******************************************/
u32 get_cpu_rev(void)
{
u32 v;
v = __raw_readl(TAP_IDCODE_REG);
v = v >> 28;
return(v+1); /* currently 2422 and 2420 match up */
}
/* optionally do something like blinking LED */
void board_hang (void)
{}