| config RC_CORE | |
| tristate | |
| depends on MEDIA_RC_SUPPORT | |
| depends on INPUT | |
| default y | |
| source "drivers/media/rc/keymaps/Kconfig" | |
| menuconfig RC_DECODERS | |
| bool "Remote controller decoders" | |
| depends on RC_CORE | |
| default y | |
| if RC_DECODERS | |
| config LIRC | |
| tristate "LIRC interface driver" | |
| depends on RC_CORE | |
| ---help--- | |
| Enable this option to build the Linux Infrared Remote | |
| Control (LIRC) core device interface driver. The LIRC | |
| interface passes raw IR to and from userspace, where the | |
| LIRC daemon handles protocol decoding for IR reception and | |
| encoding for IR transmitting (aka "blasting"). | |
| config IR_LIRC_CODEC | |
| tristate "Enable IR to LIRC bridge" | |
| depends on RC_CORE | |
| depends on LIRC | |
| default y | |
| ---help--- | |
| Enable this option to pass raw IR to and from userspace via | |
| the LIRC interface. | |
| config IR_NEC_DECODER | |
| tristate "Enable IR raw decoder for the NEC protocol" | |
| depends on RC_CORE | |
| select BITREVERSE | |
| default y | |
| ---help--- | |
| Enable this option if you have IR with NEC protocol, and | |
| if the IR is decoded in software | |
| config IR_RC5_DECODER | |
| tristate "Enable IR raw decoder for the RC-5 protocol" | |
| depends on RC_CORE | |
| select BITREVERSE | |
| default y | |
| ---help--- | |
| Enable this option if you have IR with RC-5 protocol, and | |
| if the IR is decoded in software | |
| config IR_RC6_DECODER | |
| tristate "Enable IR raw decoder for the RC6 protocol" | |
| depends on RC_CORE | |
| select BITREVERSE | |
| default y | |
| ---help--- | |
| Enable this option if you have an infrared remote control which | |
| uses the RC6 protocol, and you need software decoding support. | |
| config IR_JVC_DECODER | |
| tristate "Enable IR raw decoder for the JVC protocol" | |
| depends on RC_CORE | |
| select BITREVERSE | |
| default y | |
| ---help--- | |
| Enable this option if you have an infrared remote control which | |
| uses the JVC protocol, and you need software decoding support. | |
| config IR_SONY_DECODER | |
| tristate "Enable IR raw decoder for the Sony protocol" | |
| depends on RC_CORE | |
| select BITREVERSE | |
| default y | |
| ---help--- | |
| Enable this option if you have an infrared remote control which | |
| uses the Sony protocol, and you need software decoding support. | |
| config IR_RC5_SZ_DECODER | |
| tristate "Enable IR raw decoder for the RC-5 (streamzap) protocol" | |
| depends on RC_CORE | |
| select BITREVERSE | |
| default y | |
| ---help--- | |
| Enable this option if you have IR with RC-5 (streamzap) protocol, | |
| and if the IR is decoded in software. (The Streamzap PC Remote | |
| uses an IR protocol that is almost standard RC-5, but not quite, | |
| as it uses an additional bit). | |
| config IR_SANYO_DECODER | |
| tristate "Enable IR raw decoder for the Sanyo protocol" | |
| depends on RC_CORE | |
| default y | |
| ---help--- | |
| Enable this option if you have an infrared remote control which | |
| uses the Sanyo protocol (Sanyo, Aiwa, Chinon remotes), | |
| and you need software decoding support. | |
| config IR_MCE_KBD_DECODER | |
| tristate "Enable IR raw decoder for the MCE keyboard/mouse protocol" | |
| depends on RC_CORE | |
| select BITREVERSE | |
| default y | |
| ---help--- | |
| Enable this option if you have a Microsoft Remote Keyboard for | |
| Windows Media Center Edition, which you would like to use with | |
| a raw IR receiver in your system. | |
| endif #RC_DECODERS | |
| menuconfig RC_DEVICES | |
| bool "Remote Controller devices" | |
| depends on RC_CORE | |
| if RC_DEVICES | |
| config RC_ATI_REMOTE | |
| tristate "ATI / X10 based USB RF remote controls" | |
| depends on USB_ARCH_HAS_HCD | |
| depends on RC_CORE | |
| select USB | |
| help | |
| Say Y here if you want to use an X10 based USB remote control. | |
| These are RF remotes with USB receivers. | |
| Such devices include the ATI remote that comes with many of ATI's | |
| All-In-Wonder video cards, the X10 "Lola" remote, NVIDIA RF remote, | |
| Medion RF remote, and SnapStream FireFly remote. | |
| This driver provides mouse pointer, left and right mouse buttons, | |
| and maps all the other remote buttons to keypress events. | |
| To compile this driver as a module, choose M here: the module will be | |
| called ati_remote. | |
| config IR_ENE | |
| tristate "ENE eHome Receiver/Transceiver (pnp id: ENE0100/ENE02xxx)" | |
| depends on PNP | |
| depends on RC_CORE | |
| ---help--- | |
| Say Y here to enable support for integrated infrared receiver | |
| /transceiver made by ENE. | |
| You can see if you have it by looking at lspnp output. | |
| Output should include ENE0100 ENE0200 or something similar. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ene_ir. | |
| config IR_IMON | |
| tristate "SoundGraph iMON Receiver and Display" | |
| depends on USB_ARCH_HAS_HCD | |
| depends on RC_CORE | |
| select USB | |
| ---help--- | |
| Say Y here if you want to use a SoundGraph iMON (aka Antec Veris) | |
| IR Receiver and/or LCD/VFD/VGA display. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imon. | |
| config IR_MCEUSB | |
| tristate "Windows Media Center Ed. eHome Infrared Transceiver" | |
| depends on USB_ARCH_HAS_HCD | |
| depends on RC_CORE | |
| select USB | |
| ---help--- | |
| Say Y here if you want to use a Windows Media Center Edition | |
| eHome Infrared Transceiver. | |
| To compile this driver as a module, choose M here: the | |
| module will be called mceusb. | |
| config IR_ITE_CIR | |
| tristate "ITE Tech Inc. IT8712/IT8512 Consumer Infrared Transceiver" | |
| depends on PNP | |
| depends on RC_CORE | |
| ---help--- | |
| Say Y here to enable support for integrated infrared receivers | |
| /transceivers made by ITE Tech Inc. These are found in | |
| several ASUS devices, like the ASUS Digimatrix or the ASUS | |
| EEEBox 1501U. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ite-cir. | |
| config IR_FINTEK | |
| tristate "Fintek Consumer Infrared Transceiver" | |
| depends on PNP | |
| depends on RC_CORE | |
| ---help--- | |
| Say Y here to enable support for integrated infrared receiver | |
| /transciever made by Fintek. This chip is found on assorted | |
| Jetway motherboards (and of course, possibly others). | |
| To compile this driver as a module, choose M here: the | |
| module will be called fintek-cir. | |
| config IR_NUVOTON | |
| tristate "Nuvoton w836x7hg Consumer Infrared Transceiver" | |
| depends on PNP | |
| depends on RC_CORE | |
| ---help--- | |
| Say Y here to enable support for integrated infrared receiver | |
| /transciever made by Nuvoton (formerly Winbond). This chip is | |
| found in the ASRock ION 330HT, as well as assorted Intel | |
| DP55-series motherboards (and of course, possibly others). | |
| To compile this driver as a module, choose M here: the | |
| module will be called nuvoton-cir. | |
| config IR_REDRAT3 | |
| tristate "RedRat3 IR Transceiver" | |
| depends on USB_ARCH_HAS_HCD | |
| depends on RC_CORE | |
| select USB | |
| ---help--- | |
| Say Y here if you want to use a RedRat3 Infrared Transceiver. | |
| To compile this driver as a module, choose M here: the | |
| module will be called redrat3. | |
| config IR_STREAMZAP | |
| tristate "Streamzap PC Remote IR Receiver" | |
| depends on USB_ARCH_HAS_HCD | |
| depends on RC_CORE | |
| select USB | |
| ---help--- | |
| Say Y here if you want to use a Streamzap PC Remote | |
| Infrared Receiver. | |
| To compile this driver as a module, choose M here: the | |
| module will be called streamzap. | |
| config IR_WINBOND_CIR | |
| tristate "Winbond IR remote control" | |
| depends on X86 && PNP | |
| depends on RC_CORE | |
| select NEW_LEDS | |
| select LEDS_CLASS | |
| select LEDS_TRIGGERS | |
| select BITREVERSE | |
| ---help--- | |
| Say Y here if you want to use the IR remote functionality found | |
| in some Winbond SuperI/O chips. Currently only the WPCD376I | |
| chip is supported (included in some Intel Media series | |
| motherboards). | |
| To compile this driver as a module, choose M here: the module will | |
| be called winbond_cir. | |
| config IR_IGUANA | |
| tristate "IguanaWorks USB IR Transceiver" | |
| depends on USB_ARCH_HAS_HCD | |
| depends on RC_CORE | |
| select USB | |
| ---help--- | |
| Say Y here if you want to use the IguanaWorks USB IR Transceiver. | |
| Both infrared receive and send are supported. If you want to | |
| change the ID or the pin config, use the user space driver from | |
| IguanaWorks. | |
| Only firmware 0x0205 and later is supported. | |
| To compile this driver as a module, choose M here: the module will | |
| be called iguanair. | |
| config IR_TTUSBIR | |
| tristate "TechnoTrend USB IR Receiver" | |
| depends on USB_ARCH_HAS_HCD | |
| depends on RC_CORE | |
| select USB | |
| select NEW_LEDS | |
| select LEDS_CLASS | |
| ---help--- | |
| Say Y here if you want to use the TechnoTrend USB IR Receiver. The | |
| driver can control the led. | |
| To compile this driver as a module, choose M here: the module will | |
| be called ttusbir. | |
| config IR_RX51 | |
| tristate "Nokia N900 IR transmitter diode" | |
| depends on OMAP_DM_TIMER && ARCH_OMAP2PLUS && LIRC && !ARCH_MULTIPLATFORM | |
| ---help--- | |
| Say Y or M here if you want to enable support for the IR | |
| transmitter diode built in the Nokia N900 (RX51) device. | |
| The driver uses omap DM timers for generating the carrier | |
| wave and pulses. | |
| config RC_LOOPBACK | |
| tristate "Remote Control Loopback Driver" | |
| depends on RC_CORE | |
| ---help--- | |
| Say Y here if you want support for the remote control loopback | |
| driver which allows TX data to be sent back as RX data. | |
| This is mostly useful for debugging purposes. | |
| If you're not sure, select N here. | |
| To compile this driver as a module, choose M here: the module will | |
| be called rc_loopback. | |
| config IR_GPIO_CIR | |
| tristate "GPIO IR remote control" | |
| depends on RC_CORE | |
| ---help--- | |
| Say Y if you want to use GPIO based IR Receiver. | |
| To compile this driver as a module, choose M here: the module will | |
| be called gpio-ir-recv. | |
| endif #RC_DEVICES |