| /* |
| * Copyright (C) 2016 Nest Labs, Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include "onyx-ffd.dts" |
| |
| / { |
| model = "NestLabs Onyx Proto Board"; |
| compatible = "nestlabs,onyx-proto", "fsl,imx6ul"; |
| |
| aliases { |
| serial-ble0 = &uart2; |
| serial-sensormcu0 = &uart3; |
| }; |
| |
| /* Overlay the magwheel driver instead of the default ADC driver */ |
| soc { |
| aips-bus@02100000 { |
| magwheel: adc@02198000 { |
| compatible = "nestlabs,vf610-adc-magwheel"; |
| pinctrl-0 = <&pinctrl_adc1>; |
| vref-supply = <&adc_ref>; |
| reg = <0x02198000 0x4000>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6UL_CLK_ADC1>; |
| nestlabs,adc-channels-used = <6 7>; |
| nestlabs,adc-channel-midpoints = <1965 2038>; |
| hall-sensor-enable-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| #io-channel-cells = <1>; |
| }; |
| }; |
| }; |
| }; |
| |
| &em35x_gpios { |
| output-gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>, |
| <&gpio2 2 GPIO_ACTIVE_HIGH>; |
| input-gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| &pinctrl_em35x_gpios { |
| fsl,pins = < |
| MX6UL_PAD_SD1_DATA1__GPIO2_IO19 PAD_CONFIG__GPIO /* 6LO_RESET_L */ |
| MX6UL_PAD_SD1_DATA0__GPIO2_IO18 PAD_CONFIG__GPIO /* INT_6LO_TO_AP */ |
| MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02 PAD_CONFIG__GPIO /* INT_AP_TO_6LO */ |
| >; |
| }; |
| |
| &pinctrl_hog_extra { |
| fsl,pins = < |
| MX6UL_PAD_SD1_DATA2__CCM_CLKO1 PAD_CONFIG__DEFAULT /* CLK_32K_AP_OUT_TP */ |
| MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 PAD_CONFIG__GPIO /* RAM_PWR_EN_L */ |
| >; |
| }; |
| |
| &battery { |
| io-channels = <&magwheel 4>; /* GPIO01_IO4 */ |
| io-channel-names = "vbat"; |
| vbatt-adc-input-enable-gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>; |
| divider-r1-ohm = <715>; /* 71.5k */ |
| divider-r2-ohm = <511>; /* 51.1k */ |
| delay-us = <8000>; |
| }; |
| |
| &adc_ref{ |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| &iomuxc { |
| adc1 { |
| pinctrl_adc1: adc1grp { |
| fsl,pins = < |
| MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 PAD_CONFIG__ADC /* ADC_VBAT_AP */ |
| MX6UL_PAD_GPIO1_IO06__GPIO1_IO06 PAD_CONFIG__ADC /* ADC_MAG_1 */ |
| MX6UL_PAD_GPIO1_IO07__GPIO1_IO07 PAD_CONFIG__ADC /* ADC_MAG_2 */ |
| MX6UL_PAD_SD1_DATA3__GPIO2_IO21 PAD_CONFIG__GPIO /* AP_HEF_EN */ |
| >; |
| }; |
| }; |
| }; |
