blob: 17f230f4a1e50448fdb91a73c965da3201ec6a85 [file] [log] [blame]
/*
* (C) Copyright 2006-2010
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* mpc8349emds board configuration file
*
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_BOARDINFO
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 Family */
#define CONFIG_MPC834x 1 /* MPC834x family */
#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_MPC8349EMDS 1 /* MPC8349EMDS board specific */
#define CONFIG_SYS_TEXT_BASE 0xFE000000
#define CONFIG_PCI_66M
#ifdef CONFIG_PCI_66M
#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
#else
#define CONFIG_83XX_CLKIN 33000000 /* in Hz */
#endif
#ifdef CONFIG_PCISLAVE
#define CONFIG_PCI
#define CONFIG_83XX_PCICLK 66666666 /* in Hz */
#endif /* CONFIG_PCISLAVE */
#ifndef CONFIG_SYS_CLK_FREQ
#ifdef CONFIG_PCI_66M
#define CONFIG_SYS_CLK_FREQ 66000000
#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
#else
#define CONFIG_SYS_CLK_FREQ 33000000
#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1
#endif
#endif
#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
#define CONFIG_SYS_IMMR 0xE0000000
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x00100000
/*
* DDR Setup
*/
#define CONFIG_DDR_ECC /* support DDR ECC function */
#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
/*
* define CONFIG_SYS_FSL_DDR2 to use unified DDR driver
* undefine it to use old spd_sdram.c
*/
#define CONFIG_SYS_FSL_DDR2
#ifdef CONFIG_SYS_FSL_DDR2
#define CONFIG_SYS_FSL_DDRC_GEN2
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS1 0x52
#define SPD_EEPROM_ADDRESS2 0x51
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#endif
/*
* 32-bit data path mode.
*
* Please note that using this mode for devices with the real density of 64-bit
* effectively reduces the amount of available memory due to the effect of
* wrapping around while translating address to row/columns, for example in the
* 256MB module the upper 128MB get aliased with contents of the lower
* 128MB); normally this define should be used for devices with real 32-bit
* data path.
*/
#undef CONFIG_DDR_32BIT
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
#undef CONFIG_DDR_2T_TIMING
/*
* DDRCDR - DDR Control Driver Register
*/
#define CONFIG_SYS_DDRCDR_VALUE 0x80080001
#if defined(CONFIG_SPD_EEPROM)
/*
* Determine DDR configuration from I2C interface.
*/
#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
#else
/*
* Manually set up DDR parameters
*/
#define CONFIG_SYS_DDR_SIZE 256 /* MB */
#if defined(CONFIG_DDR_II)
#define CONFIG_SYS_DDRCDR 0x80080001
#define CONFIG_SYS_DDR_CS2_BNDS 0x0000000f
#define CONFIG_SYS_DDR_CS2_CONFIG 0x80330102
#define CONFIG_SYS_DDR_TIMING_0 0x00220802
#define CONFIG_SYS_DDR_TIMING_1 0x38357322
#define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
#define CONFIG_SYS_DDR_CLK_CNTL 0x02000000
#define CONFIG_SYS_DDR_MODE 0x47d00432
#define CONFIG_SYS_DDR_MODE2 0x8000c000
#define CONFIG_SYS_DDR_INTERVAL 0x03cf0080
#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
#else
#define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \
| CSCONFIG_ROW_BIT_13 \
| CSCONFIG_COL_BIT_10)
#define CONFIG_SYS_DDR_TIMING_1 0x36332321
#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
#define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */
#if defined(CONFIG_DDR_32BIT)
/* set burst length to 8 for 32-bit data path */
/* DLL,normal,seq,4/2.5, 8 burst len */
#define CONFIG_SYS_DDR_MODE 0x00000023
#else
/* the default burst length is 4 - for 64-bit data path */
/* DLL,normal,seq,4/2.5, 4 burst len */
#define CONFIG_SYS_DDR_MODE 0x00000022
#endif
#endif
#endif
/*
* SDRAM on the Local Bus
*/
#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */
#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
/*
* FLASH on the Local Bus
*/
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */
#define CONFIG_SYS_FLASH_SIZE 32 /* max flash size in MB */
#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
| BR_PS_16 /* 16 bit port */ \
| BR_MS_GPCM /* MSEL = GPCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
| OR_UPM_XAM \
| OR_GPCM_CSNT \
| OR_GPCM_ACS_DIV2 \
| OR_GPCM_XACS \
| OR_GPCM_SCY_15 \
| OR_GPCM_TRLX_SET \
| OR_GPCM_EHTR_SET \
| OR_GPCM_EAD)
/* window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB)
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef CONFIG_SYS_RAMBOOT
#endif
/*
* BCSR register on local bus 32KB, 8-bit wide for MDS config reg
*/
#define CONFIG_SYS_BCSR 0xE2400000
/* Access window base at BCSR base */
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \
| BR_PS_8 \
| BR_MS_GPCM \
| BR_V)
/* 0x00000801 */
#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \
| OR_GPCM_XAM \
| OR_GPCM_CSNT \
| OR_GPCM_SCY_15 \
| OR_GPCM_TRLX_CLEAR \
| OR_GPCM_EHTR_CLEAR)
/* 0xFFFFE8F0 */
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
#define CONFIG_SYS_GBL_DATA_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
/*
* Local Bus LCRR and LBCR regs
* LCRR: DLL bypass, Clock divider is 4
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
* The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory.
* if board has SRDAM on local bus, you can define CONFIG_SYS_LB_SDRAM
*/
#undef CONFIG_SYS_LB_SDRAM
#ifdef CONFIG_SYS_LB_SDRAM
/* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */
/*
* Base Register 2 and Option Register 2 configure SDRAM.
* The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
*
* For BR2, need:
* Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
* port-size = 32-bits = BR2[19:20] = 11
* no parity checking = BR2[21:22] = 00
* SDRAM for MSEL = BR2[24:26] = 011
* Valid = BR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
*/
#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_LBC_SDRAM_BASE \
| BR_PS_32 /* 32-bit port */ \
| BR_MS_SDRAM /* MSEL = SDRAM */ \
| BR_V) /* Valid */
/* 0xF0001861 */
#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE
#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB)
/*
* The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
*
* For OR2, need:
* 64MB mask for AM, OR2[0:7] = 1111 1100
* XAM, OR2[17:18] = 11
* 9 columns OR2[19-21] = 010
* 13 rows OR2[23-25] = 100
* EAD set for extra time OR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
*/
#define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB \
| OR_SDRAM_XAM \
| ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \
| ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \
| OR_SDRAM_EAD)
/* 0xFC006901 */
/* LB sdram refresh timer, about 6us */
#define CONFIG_SYS_LBC_LSRT 0x32000000
/* LB refresh timer prescal, 266MHz/32 */
#define CONFIG_SYS_LBC_MRTPR 0x20000000
#define CONFIG_SYS_LBC_LSDMR_COMMON (LSDMR_RFEN \
| LSDMR_BSMA1516 \
| LSDMR_RFCR8 \
| LSDMR_PRETOACT6 \
| LSDMR_ACTTORW3 \
| LSDMR_BL8 \
| LSDMR_WRC3 \
| LSDMR_CL3)
/*
* SDRAM Controller configuration sequence.
*/
#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
#endif
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* SPI */
#define CONFIG_MPC8XXX_SPI
#undef CONFIG_SOFT_SPI /* SPI bit-banged */
/* GPIOs. Used as SPI chip selects */
#define CONFIG_SYS_GPIO1_PRELIM
#define CONFIG_SYS_GPIO1_DIR 0xC0000000 /* SPI CS on 0, LED on 1 */
#define CONFIG_SYS_GPIO1_DAT 0xC0000000 /* Both are active LOW */
/* TSEC */
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
/* USB */
#define CONFIG_SYS_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
#define PCI_ONE_PCI1
#if defined(PCI_64BIT)
#undef PCI_ALL_PCI1
#undef PCI_TWO_PCI1
#undef PCI_ONE_PCI1
#endif
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_83XX_PCI_STREAMING
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xFIXME
#define PCI_ENET0_MEMADDR 0xFIXME
#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#endif /* CONFIG_PCI */
/*
* TSEC configuration
*/
#define CONFIG_TSEC_ENET /* TSEC ethernet support */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_GMII 1 /* MII PHY management */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "TSEC1"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC1_FLAGS TSEC_GIGABIT
#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#endif /* CONFIG_TSEC_ENET */
/*
* Configure on-board RTC
*/
#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
/*
* Environment
*/
#ifndef CONFIG_SYS_RAMBOOT
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR \
(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
#define CONFIG_ENV_SIZE 0x2000
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#else
#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_DATE
#define CONFIG_CMD_MII
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
#if defined(CONFIG_SYS_RAMBOOT)
#undef CONFIG_CMD_SAVEENV
#undef CONFIG_CMD_LOADS
#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
/* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
#if 1 /*528/264*/
#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
HRCWL_CSB_TO_CLKIN |\
HRCWL_VCO_1X2 |\
HRCWL_CORE_TO_CSB_2X1)
#elif 0 /*396/132*/
#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
HRCWL_CSB_TO_CLKIN |\
HRCWL_VCO_1X4 |\
HRCWL_CORE_TO_CSB_3X1)
#elif 0 /*264/132*/
#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
HRCWL_CSB_TO_CLKIN |\
HRCWL_VCO_1X4 |\
HRCWL_CORE_TO_CSB_2X1)
#elif 0 /*132/132*/
#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
HRCWL_CSB_TO_CLKIN |\
HRCWL_VCO_1X4 |\
HRCWL_CORE_TO_CSB_1X1)
#elif 0 /*264/264 */
#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
HRCWL_CSB_TO_CLKIN |\
HRCWL_VCO_1X4 |\
HRCWL_CORE_TO_CSB_1X1)
#endif
#ifdef CONFIG_PCISLAVE
#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_AGENT |\
HRCWH_64_BIT_PCI |\
HRCWH_PCI1_ARBITER_DISABLE |\
HRCWH_PCI2_ARBITER_DISABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_FROM_0X00000100 |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_TSEC1M_IN_GMII |\
HRCWH_TSEC2M_IN_GMII)
#else
#if defined(PCI_64BIT)
#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_64_BIT_PCI |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_PCI2_ARBITER_DISABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_FROM_0X00000100 |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_TSEC1M_IN_GMII |\
HRCWH_TSEC2M_IN_GMII)
#else
#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_32_BIT_PCI |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_PCI2_ARBITER_ENABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_FROM_0X00000100 |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_TSEC1M_IN_GMII |\
HRCWH_TSEC2M_IN_GMII)
#endif /* PCI_64BIT */
#endif /* CONFIG_PCISLAVE */
/*
* System performance
*/
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
#define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */
#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
#define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */
#define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */
/* System IO Config */
#define CONFIG_SYS_SICRH 0
#define CONFIG_SYS_SICRL SICRL_LDP_A
#define CONFIG_SYS_HID0_INIT 0x000000000
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \
| HID0_ENABLE_INSTRUCTION_CACHE)
/* #define CONFIG_SYS_HID0_FINAL (\
HID0_ENABLE_INSTRUCTION_CACHE |\
HID0_ENABLE_M_BIT |\
HID0_ENABLE_ADDRESS_BROADCAST) */
#define CONFIG_SYS_HID2 HID2_HBE
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR @ 0x00000000 */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
| BATL_PP_RW \
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
/* PCI @ 0x80000000 */
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \
| BATL_PP_RW \
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#else
#define CONFIG_SYS_IBAT1L (0)
#define CONFIG_SYS_IBAT1U (0)
#define CONFIG_SYS_IBAT2L (0)
#define CONFIG_SYS_IBAT2U (0)
#endif
#ifdef CONFIG_MPC83XX_PCI2
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \
| BATL_PP_RW \
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#else
#define CONFIG_SYS_IBAT3L (0)
#define CONFIG_SYS_IBAT3U (0)
#define CONFIG_SYS_IBAT4L (0)
#define CONFIG_SYS_IBAT4U (0)
#endif
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
#define CONFIG_SYS_IBAT6L (0xF0000000 \
| BATL_PP_RW \
| BATL_MEMCOHERENCE \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xF0000000 \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_IBAT7L (0)
#define CONFIG_SYS_IBAT7U (0)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#endif
/*
* Environment Configuration
*/
#define CONFIG_ENV_OVERWRITE
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH0
#endif
#define CONFIG_HOSTNAME mpc8349emds
#define CONFIG_ROOTPATH "/nfsroot/rootfs"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
#define CONFIG_PREBOOT "echo;" \
"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=mpc8349emds\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_nfs=run nfsargs addip addtty;" \
"bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
"load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0" \
"update=protect off fe000000 fe03ffff; " \
"era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\
"upd=run load update\0" \
"fdtaddr=780000\0" \
"fdtfile=mpc834x_mds.dtb\0" \
""
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
"$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND "run flash_self"
#endif /* __CONFIG_H */