blob: 2cf4558daaffb22232b417b1aeea841715feb951 [file] [log] [blame]
/*
* Common board functions for Siemens TAURUS (AT91SAM9G20) based boards
* (C) Copyright 2013 Siemens AG
*
* Based on:
* U-Boot file: include/configs/at91sam9260ek.h
*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* SoC must be defined first, before hardware.h is included.
* In this case SoC is defined in boards.cfg.
*/
#include <asm/hardware.h>
#define CONFIG_SYS_GENERIC_BOARD
#if defined(CONFIG_SPL_BUILD)
#define CONFIG_SYS_THUMB_BUILD
#define CONFIG_SYS_ICACHE_OFF
#define CONFIG_SYS_DCACHE_OFF
#endif
/*
* Warning: changing CONFIG_SYS_TEXT_BASE requires
* adapting the initial boot program.
* Since the linker has to swallow that define, we must use a pure
* hex number here!
*/
#define CONFIG_SYS_TEXT_BASE 0x21000000
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */
/* Misc CPU related */
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_CMD_BOOTZ
#define CONFIG_OF_LIBFDT
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
#define CONFIG_AT91_GPIO
#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_BDI
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_IMI
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_SOURCE
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_NAND
/*
* SDRAM: 1 bank, min 32, max 128 MB
* Initialized before u-boot gets started.
*/
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1
#define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024)
/*
* Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM,
* leaving the correct space for initial global data structure above
* that address while providing maximum stack area below.
*/
# define CONFIG_SYS_INIT_SP_ADDR \
(ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE)
/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
#define CONFIG_SYS_NAND_DBW_8
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13
#endif
/* NOR flash - no real flash on this board */
#define CONFIG_SYS_NO_FLASH 1
/* Ethernet */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_AT91_WANTS_COMMON_PHY
#define CONFIG_AT91SAM9_WATCHDOG
#if !defined(CONFIG_SPL_BUILD)
/* Enable the watchdog */
#define CONFIG_HW_WATCHDOG
#endif
/* USB */
#if defined(CONFIG_BOARD_TAURUS)
#define CONFIG_USB_ATMEL
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
#define CONFIG_USB_STORAGE
#endif
/* SPI EEPROM */
#define CONFIG_SPI
#define CONFIG_CMD_SPI
#define CONFIG_CMD_SF
#define CONFIG_SPI_FLASH
#define CONFIG_ATMEL_SPI
#define CONFIG_SPI_FLASH_STMICRO
#define TAURUS_SPI_MASK (1 << 4)
#define TAURUS_SPI_CS_PIN AT91_PIN_PA3
#if defined(CONFIG_SPL_BUILD)
/* SPL related */
#undef CONFIG_SPL_OS_BOOT /* Not supported by existing map */
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#endif
/* load address */
#define CONFIG_SYS_LOAD_ADDR 0x22000000
/* bootstrap in spi flash , u-boot + env + linux in nandflash */
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0x100000
#define CONFIG_ENV_OFFSET_REDUND 0x180000
#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0x200000 0x300000; bootm"
#define CONFIG_BOOTARGS \
"console=ttyS0,115200 earlyprintk " \
"mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \
"256k(env),256k(env_redundant),256k(spare)," \
"512k(dtb),6M(kernel)ro,-(rootfs) " \
"root=/dev/mtdblock7 rw rootfstype=jffs2"
#define CONFIG_SYS_PROMPT "U-Boot> "
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PBSIZE \
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN \
ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x0
#define CONFIG_SPL_MAX_SIZE (14 * 1024)
#define CONFIG_SPL_STACK (16 * 1024)
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \
CONFIG_SYS_MALLOC_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
#define CONFIG_SPL_BSS_START_ADDR CONFIG_SPL_MAX_SIZE
#define CONFIG_SPL_BSS_MAX_SIZE (3 * 1024)
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SYS_NAND_ENABLE_PIN_SPL (2*32 + 14)
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SYS_USE_NANDFLASH 1
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_NAND_RAW_ONLY
#define CONFIG_SPL_NAND_SOFTECC
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000
#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_SIZE (256*1024*1024)
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
CONFIG_SYS_NAND_PAGE_SIZE)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCSIZE 256
#define CONFIG_SYS_NAND_ECCBYTES 3
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \
48, 49, 50, 51, 52, 53, 54, 55, \
56, 57, 58, 59, 60, 61, 62, 63, }
#define CONFIG_SPL_ATMEL_SIZE
#define CONFIG_SYS_MASTER_CLOCK 132096000
#define AT91_PLL_LOCK_TIMEOUT 1000000
#define CONFIG_SYS_AT91_PLLA 0x202A3F01
#define CONFIG_SYS_MCKR 0x1300
#define CONFIG_SYS_MCKR_CSS (0x02 | CONFIG_SYS_MCKR)
#define CONFIG_SYS_AT91_PLLB 0x10193F05
#endif